Search Documents

THE morning session on non-metallic minerals was opened briefly by the chairman, Oliver Bowles, giving the usual instructions and then turning immediately to the introduction of the speakers. "Min-ing and Preparation of the St. Peter Sandstone in' Arkansas" by D. D. Dunkin was first presented by W. M. Weigel, mining technologist for the Missouri Pacific R. R. The paper covered a discussion of the geology of the sandstone, correlating it with the sand-stones at Klondike, Mo., and at Ottawa, III. Its physical appearance, structural characteristics and thickness; the mining methods, blasting, loading, haulage and classification were taken up. A series of slides aided in clarifying the details. The discussion consisted of questioning Mr. Weigel on operating details. The second paper, "Geology and Mining of Diaspore and Flint Fire-Clays of Missouri," written by H. S. McQueen, geologist with the Missouri Bureau of Geology and Mines, and C. R. Forbes, professor of mining, Missouri School of Mines and Metallurgy, was presented by Mr. Forbes. It thoroughly covered the geology, stressing the peculiar sink formations in which all diaspore clay deposits of the region occur. The crudeness of the mining methods was mentioned and believed justifiable because of the small size of the indi-vidual deposits. It was stated that the diaspore and flint clay deposits of Missouri were confined to an area 60 mi. square and it was found in a survey that the average deposit had dimensions comparable to the fol-lowing: 100 ft. long, 75 ft. wide and 50 ft. deep. The largest deposit found was 800 ft. long. 500 ft. wide and 20 ft. deep. It is estimated that the known reserve of clays is from 750.000 to 1,500,000 tons. Mr. Forbes stressed the fact that in mining clays the major problem is entirely one of sorting. This is done under the supervision of a pit foreman trained to make this classification by eye. The mine-run clays are sepa-rated into diaspore clay ranging in alumina content from 70 to about 85 per cent, first grade Burly clay 00 to 70 per cent, and Flint clay 52 to 60 per cent. Discussion of the paper consisted in questioning Pro-fessor Forbes on labor. cost, haulage, drilling, and geology.

Jan 3, 1928

By E. E. Gardner, P. A. Schumann

A description of a new four-point probe configuration which permits measurement of epitaxial layer resistivity is given. An analytic solution to the potential distribution due to a point current source on a multilayered structure is briefly described. Typical solutions for this probe configuration are presented. Probe spacing, layer thickness, substrate resistivity, and substrate thickness enter into the calculation. Correction factors for typical cases are given. A brief description of the construction of a probe which can achieve a small spacing of 15 is presented. The prohe is constructed so that all points are adjustable by micrometers and the probe spacing and configuration can be easily altered. Measurements of layer resistivity with the four-point probe are compared with those taken with the three-Point probe and diode-capacitance techniques. TWO techniques of obtaining profiles of N/N+ epitaxial structures are given. The reproducihility of the probe spacing and resistivity measurement is discussed. The effects upon the resistivity measurement of errors in the measurement of the lager thickness, substrate resistil)itv, and substrate thickness are presented. SINCE its introduction by valdes' in 1954, the four-point probe has been the most widely used tool for determining semiconductor resistivity. Its usefulness ranges from the evaluation of bulk semiconductor ingots to the characterization of impurity profiles in diffused structures. In general the four points, two current probes and two potential probes, are placed on one surface of the material being tested either in an in-line array or in a square array. Numerous correction factors1 8 have been worked out for these configurations which are dictated by the finite geometry of the sample being tested. One method of evaluating thin wafers has been proposed which has two probesg on each side of the wafer. Further modifications have added a fifth'' and a sixth" probe. One paper1' has discussed the accuracy of the four-point probe and the precautions necessary in its use. With the exception of the method where two points are placed on opposite sides of the wafer, the four-point probe is restricted to evaluation of wafers with a homogeneous resistivity or to the case where an isolating junction exists between the substrate and the layer (epitaxial or diffused) being evaluated. Due to the relative resistivities and thickness, the resistance of the epitaxial layer is much greater than that of the substrate, and consequently a majority of the current flows through the substrate. The potential distribution at relatively large distances from the current sources is determined by the substrate resistance, and hence the AV/I value is a measure of the substrate resistivity and not that of the epitaxial-layer resistivity. In the immediate vicinity of a current source the potential distribution is determined by the layer resistivity among other factors. Consequently, if the potential probe is placed very close to the current source, then with appropriate correction factors it is possible to determine the layer resistivity. This was the theoretical basis for using two closely spaced probes on opposite sides of an epitaxial wafer. However, due to mechanical problems, it is desirable to place the four probes on the same side of the wafer. This paper discusses the potential distribution in

Jan 1, 1965

C W. ROLFE, Professor of Geology, Emeritus, has of-fered a prize of $250 for the most valuable contribu-tion toward a new, better, or increased use of any mineral resource of the State of Illinois. The prize is open to anyone engaged in research, either privately, commercially, or in connection with any univer-sity or college staff, or any state or national bureau or sur-vey. The work must have been done, or at least completed, curing the year named. Three copies of the paper or books must be in the hands of the chairman of the committee on or before 6 p. m., May 1, 1928. If an unpublished paper is submitted, it should be typewritten, double spaced, on 8 1/2 by 11-in. paper. Unpublished results of study, or papers or books pub-lished since May 1, 1927, and before May 1, 1928, may be offered in the competition; but the results of the study must show real present or prospective economic value. Address all contributions and correspondence to Rolfe Prize Committee, 209 Transportation Building, University of Illinois, Urbana, Ill.

Jan 3, 1928

Engineering Council has been elected to membership in the Chamber of Commerce of the United States. Its representative will be Mr. Harold W. Buck, of Viele, Blackwell & Buck, Consulting Engineers, New York City, Past-president of the American Institute of Electrical Engineers, his alternate being Mr. Irving E. Moultrop, of the Edison Electric Illum-inating Co., Boston, member of American Society of Mechanical Engin-eers and American Institute of Electrical Engineers. The Chamber of Commerce of the United States was formed in 1912 and now consists of more than 1100 organizations in every state of the union, in the out-lying possessions, and of all the principal American chambers of commerce abroad. One of the chief aims is to obtain the best business thought on national questions that concern business. Members of the National Chamber have the privilege of using all the facilities of the Chamber's offices in Washington when information is desired.

Jan 12, 1919

By G. A. Stamboltzis, N. Arbiter, C. C. Harris

Fracture under low-velocity free-fall and double impact and under slow compression have been investigated. The pattern of breakage and the size distribution of resulting fragments of sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of maximum compression as determined by mathematical analysis. Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low-velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments. This work had its origin in a desire to understand three fundamental processes involved in autogenous comminution: namely; free-fall impact, double impact, and slow compression. To simplify the investigation, it is preferable to reduce the entire multi-stage fracture process to its most elementary form; that is, to study products resulting from a single-stage operation, such as the breakage of a specimen under single fracture conditions. The goal of this research is to study the energy utilization in the single fracture of brittle specimens and to relate the pattern of breakage and the resultant fragment size distribution with the nature of the material, the specimen size, the manner of load application, and the rate of loading. Published works on single fracture have mainly been concerned with tests on large (> 1-in.) irregular mineral pieces, especially coal and coke. These were mainly friability tests employing a single blow on closely sized pieces. More recently, small mineral specimens in the sieve range and glass spheres have been investigated.5-7 Kick8 has reported free-fall and double impact tests with large large cast-iron, cement, and clay spheres. The establishment of a minimum breaking height independent of size in the free-fall impact tests, and the direct proportionality between the minimum work required for fracture and the volume of the specimen in double impact tests were used by Kick as an experimental proof of his classical law of "Proportional Resistances." In the present work, spherical shapes were chosen because of their simple body geometry and consequent impact and stress field symmetry. Because the study involves several physical principles in connection with brittle-fracture, it may be of interest in fields where the strength of materials is of importance. APPARATUS The equipment for the free-fall impact testing is illustrated in Figs. 1 and 2. This consisted of a massive (17 x 17 x 3-in.) hard steel plate onto which specimens were dropped and a specimen release mechanism which could be set at any desired height up to 10 ft above the plate so that the impact velocity could be varied up to about 25 ft per sec. Double impact breakage is characterized by two points of loading situated at opposite poles. For this mode of breakage the apparatus was modified (Figs. 3, 4 and 5) so that a falling mass provided an impact of predetermined magnitude on a specimen resting on the plate. A spring-loaded device operated immediately after fracture to arrest the falling mass and to record its residual kinetic energy. Precautions were taken to avoid secondary breakage. Slow compression tests were performed on a conventional hydraulic testing machine, the specimen being held between two hardened parallel bearing blocks. In the case of glass spheres, carbide bits were used. Photoelasticity studies were performed on two-dimensional models held in a loading frame equipped with a force gauge (Fig. 6). The models were viewed in a polariscope and isochromatic fringe patterns were recorded photographically. SPECIMENS Sand-Cement Spheres: A series of sand-cement spheres were prepared by molding in spherical glass flasks.

Jan 1, 1970

THE late steel strike resulted in an unusual reversal of field when Brazilian interests shipped steel to the United States to assure completion of a blast furnace under construction in Cleveland for the national Volta Redonda mill. The furnace is one of the key factors in an expansion program scheduled to raise Brazilian steel production by 280,000 tons, bringing annual output to 1 million tons. The first consignment shipped to Cleveland included 500 tons of slab and plate steel, and was followed later by another 300 tons. Brazil wants to blow in the furnace by July 1, 1953, and the restricted allocation system brought about by the steel shortage offered a real threat to the deadline. Volta Redonda, established during World War II by Brazilian and American financing, accounts for more than half of Brazil's steel production.

Jan 1, 1952

By W. H. Howard

As the result of a series of analyses and volume determinations of gases discharged from the converters at the Garfield Smelting Co.'s. smelter at Garfield, Utah, it was found that a considerable amount of lead fume was escaping from the stacks of the converter plant, and `that if this lead could be recovered at a reasonable expense an attempt should be made to collect it. Two methods suggested themselves: (1) filtration through bags; (2) electrical precipitation of the condensed fume by a Cottrell plant. Filtration through Bags Tests were made in filtering converter gases through the ordinary woolen bags of lead-smelter bag houses to determine how long such material could withstand the corrosive action of the gases. While blowing on white metal only, the fabric was usually destroyed in 10 to 14 hr. In tests conducted in filtering gases when blowing on matte or slagging stage exclusively and when relatively considerable lead was being volatilized, bags in one instance lasted 60.5 hr. It therefore was evident that the Garfield converter gases did not contain in themselves sufficient neutralizing elements for the purpose of direct bag filtration, even during the slagging stage. Such results were more or less anticipated, but it was thus proved that under all conditions of blowing Garfield mattes a very considerable amount of neutralizing agent, zinc oxide or lime, or both combined, as in the Sprague process, would be required to render bag filtration possible. Again, owing to the constantly changing quantities of SO3 from a given battery of converters, depending on the number blowing at a given time and on the stages of the blow, it would be practically impossible to feed automatically the required amount of neutralizer. In order to safeguard the bags sufficient neutralizer would have to be continuously added to meet the maximum SO3 output, thus. wasting neutralizers and giving an undesirably diluted final product. Such a condition is entirely different

Jan 8, 1914

By A. E. Nehrenberg

R. A. Schmucker, Jr.—The writer wishes to point out that an acicular growth of austenite, similar to that described in the author's paper, was recently observed in an alloy steel of only 0.06 C content. This steel, which represents an 0.07 max C, 1.35 Cr, 0.55 Ni, 0.20 Mo analysis, combines the characteristics of minimum hardness in the annealed condition with maximum hardenability and is therefore suited primarily for cold-hobbing applications. The acicular austenite formation in this steel was observed accidentally during a determination of its Ac1 temperature. The samples used in this investigation represented as-forged bar stock which had been given a preliminary temper at 1300°F. The critical (Ac1) temperature was finally established at 1400 °F. Fig. 15 represents the microstructure of the sample which had been heated at 1450°F for ½ hr, water quenched, and tempered at 600°F for ½ hr (for the purpose of darkening the martensite). It will be observed from the distribution of the darkened areas of martensite that the parent austenite grains formed at 1450°F had grown in an acicular manner and still occupied only a small percentage of the total area. The remainder of the area contains the original equiaxed ferrite grains in which new austenite had as yet scarcely formed. However, the tiny isolated martensitic patches at several points where three or more ferrite grains intersect indicate that small austenite grains had formed and started to grow in an apparently equiaxed fashion. Fig. 16 represents the prior microstructure of an original sample in the as-forged and tempered condition, before it was heated -above the critical temperature. It is probable that there are two kinds of ferrite in this structure: (1) The equiaxed proeutectoid ferrite grains which separated from the austenite when the steel was cooled from the forging temperature, and (2) the acicular ferrite associated with the aggregate of fine carbide which is represented by the patches of

Jan 1, 1951

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By Richard P. Rothwell

FIRES in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it was not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity ; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. (Causes of Mine Fires.-Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable them to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

Jan 1, 1876

By A. Hamilton Garner

Northern Venezuela has been divided into three provinces, as follows: The Llanos, the Andean, and the Maracaibo Basin and Falcon. The first and third are large sedimentary basins offering, possibilities for oil accumulations. Oil is known to occur in many formations ranging in age from Cretaceous to Quaternary. The most prolific source of oil is probably the Cretaceous shales and limestones, from which the oil appears to have migrated into overlying porous beds. Faulting or fracturing, folding, and porosity are governing factors in the localization of commercial deposits. THE occurrence of oil seepages in Venezuela has been known since the early days of Spanish occupation. It was not until 1912, however, that any serious exploration work was undertaken. In that year, the Caribbean Petroleum Co., then a subsidiary of the General Asphalt Co., employed a large staff of geologists to make a systematic survey, of large areas in eastern and western Venezuela, selecting the most, desirable localities out of the immense area covered by the Valladares concession. This preliminary work was completed in the fall of 1913, and in February, 1914, the company completed its first commercial well at Mene Grande. Development work has progressed slowly, for various reasons, but petroleum in quantity has been encountered in nine widely separated localities. The Mene Grande field has been put on a producing basis and approximately 4,000,000 bbl. of oil are being shipped annually. Increasing quantities of oil are now being drawn from El Mene and La Rosa. In the light of these developments, the world's need for oil reserves, and the proximity of Venezuela to the United States, American capital is being attracted more and more to Venezuela. Although considerable careful geological work has been done in Venezuela by the various oil companies now operating, most of the data is. buried in the company,, files, and the published literature has been extremely meager. The most valuable contribution to date has been a map and report by Jahn, which, as it was printed in Spanish, is not. generally available to the American oil public.

Jan 10, 1924

By Pedro Beltrán

DURING the war South America attained a very important position in the production of metals and minerals, brought about by her strategic location near the "Arsenal of Democracy" and the loyalty of her peoples to the cause of freedom This seemingly miraculous achievement in the wartime delivery of the all-essential metals-copper, tin, lead, zinc and tungsten -as well as 35 other war-important minerals and metals, was not the simple result of orders received and of routine production It was the end result of pioneering, prospecting, developing, planning and plodding throughout the lifetime of your organization It was the introduction of new engineering principles, mining techniques, smelting procedures and refining practices, which presaged the entrance of the vast amount of venture capital essential to carry these promising mineral potentials through the dangerous stages of early development Many of those attending the meeting must in the past, as young engineers, have braved the untold hardships and discouragements that beset them at every turn Only they can really appreciate the true meaning of the overwhelming wartime demand on the mineral production of every one of the South American countries No one country has all of everything necessary to produce armaments on a scale imperative during an emergency Not even the United States, with its wealth of natural resources, could hope to meet the unprecedented de-

Jan 1, 1947

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By F. W. Gordon

THE Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three, main stages of development in the accompanying drawings. Fig. 1 is the stove of 1869, the, year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the-cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrate the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down. between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the. restricted area of the passages and the many reversals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28' 6'". Another reason was that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22' X 28 1/2' stove held the field for several years. A slight change made from this was to the 18' X 40' stove, where the height was increased, but the number of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little less it was not any better. The next important change, seen in Fig. 2, was by increasing the height to 60 feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decreased by alternating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfaction, but; although the proper doors were provided, it was very difficult to clean, owing to the long distance the scrapers had to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost without impairing in any yaw the

Jan 1, 1881

By V. F. Marsters

Peru has produced petroleum since the early seventies, the first work being in the Zorritos field, in the Province of Tumbes, adjoining Ecuador. In the early nineties, the Negritos field, in the Department of Piura, came into prominence, and by 1905 had attained an annual production of 335,160 bbl. The early development of the field was under the general direction of the London & Pacific Petroleum Co., but it is now handled by the International Petroleum Co. In 1900 and 1901, the Lobitos field became the seene of marked activity. In 1905, its total production amounted to 75,000 bbl.; it has continued to increase, as has Negritos. From 1897 to 1902, there was prospecting in the region of La Brieta (or Fernandex), on the Mancora River, about 25 to 30 km. from the coast. Small production of a heavy oil was obtained from three different sands. So far as the author knows, no work has been done in that locality since 1902. There are thus four distinct fields in the north end of the Peruvian coasta1 plain. The remaining productive locality of Peru is the Pirin or Pusi field, at the northwest end of Lake Titicaca, Department of Puno, in southern Peru. The first prospecting near Pusi was done by Brown Brothers, of Los Angeles, Calif., who obtained modest production about 1906; according to reports, activities ceased about 1914 or 1915. The maximum annual production was obtained about 1908, estimated at 76,000 barrels. Peru possesses two distinct geographic provinces in which we may look for the development of a larger oil industry; namely, the coastal plain province, and the inter-Andean plains. Coastal Plain Province The coastal province is most prominently developed in the Province. of Tumbes and the Departments of Piura, and Lambayeque.l It 1 For details concerning the geology of this part of Peru, see Bol. No. 50, Cuerpo de Ingenirros de Minas "Informe preliminar sobre In Zona Petrolifera del Norte del Peru," par V. 1". Marsters.

Jan 1, 1923

By C. S. Simons

The conversion of a successful research and development effort into a money-making business venture requires careful attention. Problems of a business nature, such as market size, product selling price, raw materials and fuel availability and cost, financing factors, local and national taxes, licensing arrangements, etc. must, of course, be considered and resolved. In addition, the technical questions involving the scale-up of pilot plant or laboratory results to the full-scale plant must be resolved in order to avoid the financial disaster that attends a major delay in the startup of a commercial facility. The very difficult and demanding task of providing the interface between the research laboratory and the profitable metals processing plant will be discussed with examples from the author's extensive experience. After I had accepted the invitation to present a paper on the above subject of the interface between R & D and production operations, I began to give some serious thought to the subject. The program chairman had told me, in conveying the invitation, that what the committee had in mind was a discussion of positive and negative, forces in that interface, based on "gray-hair" experience. I am, therefore, at least physically qualified! My first reaction was one of mild shock; after over twenty years in the direct pursuit of the conversion of research and development findings into plant operations, I had never tried to sort out my , experience into a formal system of DO'S and DON'TS for the edification of posterity. However, after a little further reflection, I realized that this carries no stigma. No one has been able to formulate such a set of rules, and it is not really very likely to be done. Particularly if they are to be practical. I shall therefore settle for a more modest goal; I will simply discuss the factors that I have come to believe are the most critical in insuring that re- search and development results are converted into successful operation.

Jan 1, 1973

Jan 1, 1955

By E. M. Tory, P. T. Shannon

An analysis of batch and continuous thickening in terms of the movement of planes of constant concentration (i.e. continuity waves) is presented. Use of solids flux as a primary variable greatly facilitates the analysis and clarifies the relationship between batch and continuous thickening. An "ideal" slurry is defined as one whose settling rate is a function only of the local solids concentration. An analysis of continuous thickening of this ideal slurry in an ideal thickener explains many aspects of the steady — and unsteady — state behavior of real slurries, such as the main features of a thickener's "solids profile" (including the break attributed to rake action), the sudden appearance at abnormally high feed rates of a zone of constant concentration and the velocity with which it rises, and the effect of detention time at constant weight of sludge per unit area. Where deviations exist, they are explained in terms of the batch settling behavior of real slurries. The purpose of this paper is to interpret continuous thickening phenomena in terms of batch settling behavior. Both types of thickening may be considered as the process of propagating concentration changes, due to the downward movement of the solids, from the bottom of the settling vessel upward through the slurry.' These concentration changes may be either finite or infinitesimal as in the case of the propagation of a continuous concentration gradient. The slurry itself may be moving downward as in the case of continuous thickening. The downward velocity of the slurry may be such that the concentration changes being propagated up from below remain stationary relative to the thickener walls. This is the case for steady-state thickening. It seems appropriate to analyze continuous thickening in terms of the movement of planes of constant concentration. This has already been done for batch settling."3 Although our main interest is in real slurries, there are certain aspects of both types of settling which can be deduced from a theoretical analysis of highly idealized systems. To this end, an "ideal slurry" is defined as one for which the dimensionless settling rate at any point is a function only of the local solids concentration.1,2 An "ideal thickener" is one in which there is no radial variation in either the solids concentration or in the downward component of slurry velocity. The underflow outlet is a point sink. It is to be expected that the behavior of non-ideal systems will deviate in some measure from theoretical results. However, the same characteristics which cause deviations in continuous thickening should be evident in batch settling, permitting a rational explanation of the former in terms of the latter. PREDICTED RESULTS FOR AN IDEAL SLURRY IN AN IDEAL CONTINUOUS THICKENER General Theory: In continuous thickening, the downward solids flux (mass/area-time) relative to the thickener, G, results from two different

Jan 1, 1967

By R. M. Rose, C. S. Tedmon, J. Wulff

It is frequently of interest to study the influence of small quantities of interstitial impurities on the properties of various refractory metals and alloys.

Jan 1, 1964

By R. N. Orava

TO the author's knowledge, only one satisfactory high-resolution technique for etch-pitting dislocations in Cu-Zn alloys has been published.' In that account, pits in 70/30 brass single crystals were produced by etching electrolytic ally in a 30 pct orthophosphoric acid bath. Thereafter, observations were made from surface replicas by electron microscopy. The method of pitting and observation permitted the high resolution necessary for the distinction of individual dislocations in arrays of pile-ups. However, no comment was offered concerning the possibility of obtaining pits which are amenable to optical resolution. Moreover, for adequate results, the electrolytic pitting process is invariably preceded by a polishing stage which could obscure the surface features of interest. Consequently, it would be desirable to be able to delineate, by solely chemical means, dislocations which could be detected by both optical and electron metallo-graphic techniques. This was achieved by the simple expedient of modifying two etchants reported by young2 to reveal dislocations on the (100) planes of pure copper. Single crystals of 70/30 a brass, described previously,3 were sectioned to provide a surface parallel to a set of {100) planes, mechanically polished, and subsequently electropolished at 2.4 v in a solution comprised of 2 parts H3PO4, 4 parts ethanol, and 3 parts water. The inclusion of ethanol tended to inhibit nonuniform surface attack. Etch-pitting was effected by a 2 to 3 sec immersion in a 70 pct aqueous solution of HNO3. The samples were then washed in a fast-flowing stream of water, and rinsed further in distilled water, and ethanol, before drying. It is important to note that this reagent should be either used immediately after mixing, or, if allowed to cool, reheated to about 35°C prior to use. No pitting was obtained at room temperature. Typical results are shown in Fig. 1 where (a) is an optical view of the pitted surface and (b) is an electron micrograph of a silicon monoxide replica shadowed with tungsten oxide. The former is characteristic of a somewhat longer etching time (-6 to 8 sec) which varied with bath temperature. Similar pits accrued from a 1/10 aqueous dilution of another of Young's solutions2—2 M FeC1,6H20 and 7.8 M HBr.

Jan 1, 1968