Search Documents

By M. D. Hassialis, Arthur F. Taggart

WARK1 observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility=product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith. The experimental work comprised. accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1946

[University of Alabama University, Alabama Mining and Metallurgical Society (Inactive) University of Arizona Tucson, Arizona Miners' Society ROBERT HIGH, President RICHARD FLAGG, Secretary J. B. CUNNINGHAM, Faculty Sponsor Birmingham-Southern College Birmingham, Alabama Geology Journal Club (Inactive)]

Jan 1, 1946

By M. D. Hassialis

[Surface Areas of Concentrates and Collector Coatings (T.P. 2002, by A. M. GAUDIN and G. S. PRELLER, Min. Tech., May. Discussion by M. D. HASSIALIS and the authors) . I Activation of Minerals and Adsorption of Collectors (T.P. 2082 by J. ROGERS and K. 1'. SUTHERLAND, Min. Tech., Nov. Discussion by A. F. TAGGART and the authors). . . . 3 Correlation between Mineral Behavior in Cataphoresis and in Flotation (T.P. 2005 by A. If. GAUDIN and S. C. SUN, Min. Tech., May. Discussion by M. D. HASSIALIS). . . . . . 8] Surface Areas of Concentrates and Collector Coatings M. D. HASSIALIS.*-In the current flotation theories there exists a common gap spanned by a common assumption pertaining to the arrangement and orientation of the collector ions at the solid surface. Also common is the belief that contact angle and flotation performance are dependent upon the arrangement and orientation of collector ions. This stimulating and informative paper sheds some light upon this general problem. One of the indices of arrangement is the area available per collector ion; in this connection, Gaudin and Preller have applied the B.E.T. method for surface determinations. In a surprising number of cases, their results show a greater specific surface for tailing than for concentrate. This cannot be accounted for by the differences in specific gravity and is attributed to the presence of clay minerals of "primary" sluices in the tailing. This is not a satisfactory explanation, for experience shows that when free slimed clay minerals are present in a flotation cell they will be carried mechanically into the concentrate. A part of the answer to the decreased specific surface of the concentrate would appear to be its usual flocculated condition, yet this should not entirely account for the large spreads reported. The possibility occurs that the nitrogen adsorption isotherms for clean mineral and collector-coated mineral are different. If that were true, and if the coated mineral surface exhibited decreased adsorptive powers, the discrepancy might vanish. In discussing the disposition of collector ions at mineral surfaces, the authors adopt the more consistent viewpoint that there exists some agreement between the ions of the substrate and those of the superstrate. In the case of xanthate ions on galena, a possible arrangement is shown in Fig. 2. This arrangement shows every xanthate ion being shared by two lead ions, whereas the chemical composition calls for two xanthate ions for each lead ion (p. g). This whole discussion is misleading. In the first place, it is known that xanthate ions are not abstracted by unoxidized galena, hence Fig. 2 should show as the substrate not Pbs but PbS„ Om. It would be equally erroneous to use the lattice arrangement of PGSO4, since the surface properties of xanthate-conditioned anglesite differ from those of xanthated galena. It is highly probable that the state of the galena surface exploited in its flotation is ephemeral, since weathered galena is only poorly, if at all, collected by xanthate. Just how a substrate of oxidized galena is to be pictured depends upon one's conception of the transformation from galena to anglesite. This writer is inclined to the following sequence of events. Surface sulphide ions undergo progressive oxidation. As more oxygen is taken up by the sulphide ions they become displaced from their equilibrium positions in the galena lattice, thus accommodating for the larger volume of the S„ Om ions. Concomittant with this change the forces acting on the lead ions

Jan 1, 1946

By W. T. Bishop

FOR many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. HISTORY The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and coat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree-rosin and turpentine-but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is, supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores" industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.1 In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1946

[L. W. KEMPF, Chairman E. E. SCHUMACHER, Past-Chairman E. A. ANDERSON, Senior Vice-Chairman A. A. SMITH, JR., Vice-Chairman 11. A. MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N. Y. Executive Committee 1947 C. Y. CLAYTON A. B. GRENINGER CURTIS PIGOTT 1948 WALTER BONSACK W. A. DEAN LOUIS JORDAN 1949 J. D. HANAWALT W. A. JOHNSON E. W. PALMER]

Jan 1, 1946

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946

By A. Lee Barrett

THE Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present to the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated- in-fact, considerable data have already been accumulated-that next year complete maintenance costs by districts can be presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies through- out the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1946

By J. E. Norton

PRODUCTION statistics show that during the period of emergence from the depres¬sion the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee + was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1939 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechaniza¬tion program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. SUMMER WORK An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the ac¬celerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con¬cerning the coal industry to the under¬graduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program - was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war badly scrambled the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid develop¬ment in some men. We could readily single out the men at the opposite ends of the scale of competence. COMPREHENSIVE TRAINING PROGRAM Having adopted summer work as a

Jan 1, 1946

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By L. F. Bishop

The ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill is a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various methods in use for the second six months of 1944 are shown in Table I. This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

DURING the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,1 in his treatise on-magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 200 to 300°C. (68° to 572°F.) and the results of Vosskühler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Keil2 have also reported the creep properties of a forged magnesium-cerium-manganese alloy at 200° and 250°C. (392° and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554°F.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 percent Mn have been found on the German .BMW-801D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both .the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per, cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at elevated temperatures. The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The

Jan 1, 1946

By Charles M. Brinckerhoff

The Potrerillos mine of the Andes Copper Mining Co., a subsidiary of Anaconda Copper Mining Co., is 100 miles east of the coast town of Chanaral, in the Province of Atacama, Chile. In December 1926, the plant was placed in operation and has operated continuously ever since. Block caving is the only mining method used, as it is especially suited to the grade of ore, the position and shape of the ore bodies, and the character of the ground. At the present time there are three haulage levels, which handle oxide and sulphide ores, and production from them averages 31,000 short tons daily. The purpose of this paper is to describe the layout, equipment and systems used on the gathering or main haulage levels. Haulage Layout Because of the shapes of the ore bodies, their distances from the dumping pockets

Jan 1, 1946

By W. W. Schmittroth, A. Y. Bethune

THE commercial analysis of Special High-Grade zinc usually involves the determination of lead, iron, copper and cadmium as impurities in the base metal. Over the past 20 years, as the result of metallurgical improvements in the art of producing Special High-Grade zinc metal there has taken place a gradual exclusion of almost all extraneous elements, and the few that do remain in the final product have been virtually reduced to the vanishing point. Thousands of tons of zinc .are now commercially produced annually and made available to the trade, in which impurities are present only in the order of 0.0010 per cent or less and the sum total of all impurities does not exceed 0.0025 per cent. To such zinc the term "superpurity" might well be applied without undue exaggeration. The techniques used for production control and final analysis of Special High-Grade zinc by means of emission spectra in the laboratories of the electrolytic zinc plant of the Sullivan Mining Co. are based on the premise that self-electrodes are to be preferred over all other forms for the examination of the zinc in question. Furthermore, after a survey of the literature and considerable experimental work,1 it was decided that the spectrographic method of internal control, the principle of which was first announced by Gerlach,2 using a modification of the high-voltage alternating-current arc source introduced by Duffendack and Thompson,3 with the calibration of each photographic plate as recommended by Wolfe,4 would yield the most accurate and reproducible results. Self-electrodes were chosen in order to make use of one of the unique advantages inherent in spectrographic analysis; namely, the rapid and almost effortless detection of elements other than those being quantified by the analyst; or conversely, the proof that the zinc is free from such impurities if no spectral line of the suspected element appears. This fact was verified for certain elements, and will be discussed later. Carbon electrodes impregnated or packed with zinc salts chemically prepared from the zinc to be assayed were avoided for a number of reasons. First, the chemical manipulation was another time-consuming step, which increased the chances for contamination. Second, none of the common zinc salts, such as the chloride, nitrate or sulphate, yielded reproducible results under our conditions, nor did the spectral line of the impurity appear as readily in the low concentrations as when using zinc metal. Third, no commercial carbon, except the very expensive, was pure enough to use with this grade of zinc and the continued time, effort and expense incurred in the purification of carbon was not desirable. The use of Special High-Grade zinc self-electrodes introduces certain complications with regard to obtaining satisfactory excitation conditions, because it seems necessary to raise the temperature

Jan 1, 1946

By A. E. Back, K. E. Tame, W. F. Wyman, S. F. Ravitz

IN 1940, when it appeared that the United States soon might be cut off from foreign sources of high-grade manganese ore, the Bureau of Mines began an extensive series of investigations on the production of ferrgrade products from low-grade domestic ores by ore-dressing, pyrometallurgical, and hydrometallurgical methods. Among the hydrometallurgical processes for oxide ores investigated was a sulphur dioxide process in which the manganese was recovered from solution by precipitation with lime;1 this process is essentially as follows: The ground ore is suspended in water and leached with SO2 gas to extract the manganese as manganese sulphate. Calcium chloride is then added to the slurry to precipitate calcium sulphate and form manganous chloride solution, and the resultant slurry is filtered to remove the calcium sulphate together with the in- soluble portion of the ore. Calcium hydroxide is added to the filtrate and the mixture is agitated with air to precipitate hydrated oxides of manganese and regenerate calcium chloride. The precipitate is calcined, and the calcium chloride is recycled. To determine manganese extraction, reagent consumption, grade of product, and similar data for this process, a laboratory investigation was started. Two minor modifications in the process were soon made: (I) the ore was suspended in calcium chloride solution instead of in water in order to extract the manganese and precipitate the calcium sulphate in one step, and (2) the agitation with air after the addition of slaked lime to the filtrate was omitted because manganese hydroxide is readily precipitated without air agitation and can be nodulized or sintered to a satisfactory product. When the process was carried through a series of cyclic tests, it was noted that the concentration of dithionate ion (which is one of the products of oxidation of SO2 by MnOz) in the cycled solution gradually increased; at the same time the chloride content of the solution gradually decreased, owing to soluble losses in the leach residue and in the precipitate. After a number of cycles, the calcium chloride became virtually completely replaced by calcium dithionate, the quantity of dithionate ion formed during the leach being more than enough to make up for the losses of dithionate in filtering. The calcium chloride process thus developed into a calcium dithionate process. Since the latter eliminated the need for make-up calcium chloride, and the dithionate solutions appeared much less corrosive than the chloride solutions, work on the calcium chloride process was dropped in favor of the calcium dithionate process. ACKNOWLEDGMENTS The dithionate process was developed by the Bureau of Mines as part of a

Jan 1, 1946

By C. G. Dunn

IT is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.1 In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth-processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insufficient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered. Until recently observations were that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro- structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1946

By T. E. Leontis, F. N. Rhines

THE oxide scale that forms upon magnesium at elevated temperatures is nonprotective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth1 and has been verified by Suzuki2 and by Scheil.3 Pilling and Bedworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki,2 the product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavault5 observed that excrescences form upon liquid magnesium and alloys in the course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium7and calcium8 minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.9 Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Scheil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. EXPERIMENTAL PROCEDURE AND RESULTS The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the

Jan 1, 1946

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain Members.

Jan 1, 1946

By G. K. Manning, C. H. Lorig

Two metallurgical tools have acquired wide use within the past several years as a means of studying the transformation characteristics of steel. One is a technique used first by Bain and Davenport for determining the transformation characteristics of a steel at constant temperature; the second is the end-quench hardenability test. Constant-temperature transformation curves like those of Bain and Davenport have done much to rationalize the metal¬lography of steel; however, in commercial practices, constant-temperature transformation is seldom encountered, therefore only rarely can such curves be directly applied. The real reason for the determination of such curves lies, in the fact that they provide a way of thinking about transformation that is both convenient and productive. The end-quench hardenability test is a more practical means of studying transformation, for, by correlating positions on the hardenability bar with shapes of different masses, an almost direct application of the results can be made. Unfortunately, the end-quench test, though practical, can do very little toward improving the metallurgists' way of thinking about transformation. These two metallurgical tools, dealing with precisely the same phenomenon, should be very closely associated in metallurgists' minds. Actually, they are frequently pushed into separate mental corners and considered as being more or less distinct and unrelated. The reason for this is that no strong connecting link between them has been developed. An attempt is sometimes made to relate these two tools by projecting the critical cooling rate on the isothermal transformation plot as illustrated in Fig. I. The critical cooling rate is considered as a constant rate-though in practical applications, cooling rates are never constant-and this constant cooling rate is given uniform significance from the Ae temperature down to the temperature of initial transformation. A little thought indicates the errors of such a procedure. Certainly the time interval spent just below point A of Fig. I cannot be as effective in promoting nucleation as is the time interval spent just above point B. Yet the procedure represented in Fig. I considers all the time spent between temperatures A and B to be just as effective in promoting nucleation as though all the time were spent at temperature B. Furthermore, change the shape of the isothermal curve between points B and C in any way desired, and the required critical cooling rate is not changed one iota. This cannot possibly be true. Such a way of thinking about critical cooling rates not only is incapable of giving any results that are quantitatively satisfactory but is likely to give very misleading qualitative results.

Jan 1, 1946

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. PURPOSE Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls

Jan 1, 1946