Search Documents

By R. G. Knickerbocker, R. R. Lloyd, W. T. Rawles

In July 1041, the Experiment Station of the Bureau of Mines at Boulder City, Nevada, began a study of methods of producing magnesium metal from magnesium oxide, with particular emphasis upon the direct use of magnesium oxide in a molten chloride electrolyte. The program was extended to include pilot-plant study of chemical methods for the preparation of pure magnesia from dolomites and magnesites. Preliminary work on the production of magnesia from dolomite was done with the cooperation of Kobert D. Pike and the Harbison-Walker Refractories Co. These investigatipns included a cooperative arrangement whereby the Bureau tested certain steps of the Harbison-Walker-Pike process. The process finally developed by the Bureau includes the precarbonation mixing step of the H.W.P. flowsheet prepared by Mr. Pike. Two magnesium-reduction plants using MgO as a source of magnesium were being constructed in the West, and they enormously stimulated interest in various dolomite deposits as possible sources of the magnesia needed by them. This paper describes one phase of this program—the operation of a pilot plant for producing cell-grade magnesia from dolomite from Sloan, Nevada. The process developed for this purpose is an adaptation of a well-known process first proposed by Clossonl and modified by others,2"1 involving the use of calcium chloride and carbon dioxide. It is based on the following chemical reactions: MgCl2 + Ca(OH)2 = CaCl2 + Mg(OH)2 [1] Mg(OH)4 + CaCU + CO2 = MgCl2 + CaCO, + H2O [2] The first reaction proceeds almost completely to the right because of the much greater solubility of calcium hydroxide as compared with magnesium hydroxide. Under equilibrium conditions, when only the four components shown in reaction I are involved, the ratio of magnesium to calcium in solution, according to solubility-product relationship, will be: This reaction is the basis of present commercial processes for recovering magnesium from sea water and dolomite. The second reaction is, in effect, a reversal of the first reaction produced by adding COz. This reaction also proceeds nearly to completion, the solubility relationship being: Ca where P indicates partial pressure of COz, in atmospheres.

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By L. R. Jackson

THE idea presented in this paper is that the capacity of a metal for plastic flow before rupture is dependent on the type of stress system applied-that is, the absolute magnitude of the stresses are unimportant provided that they are large enough to produce continued flow; the important factor is the "type" of stress system. A term called the "triaxial stress ratio" is defined in such a way that this ratio can be used to characterize the "type" of system. The paper is divided into three sections. The first section discusses means of representing the effect of complex stresses on plastic flow and defines "triaxial stress ratio"; the second section discusses various methods of' obtaining complex stress distribution. The third section gives some experimental results showing the effect of types of complex stress on the capacity of various metals for flow. An appendix discusses some details on methods of obtaining complex stresses. I. REPRESENTATION OF COMPLEX STRESS SYSTEMS AND THEIR EFFECT ON PLASTIC FLOW Representation of Stresses It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses [S1 S2 5 S3]. This system can be resolved into a new system consisting of the three components [ ] and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation [ ] Sm is given by Eq. I and S1 is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. [ ] Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1944

THE Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysicists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1944

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By Louise Barton Freeman, Coleman D. Hunter

The total production of oil in Kentucky during the year 1943 reached 7,010,776 bbl., which is more than at any time since 1930. Of this total, 5,287,659 bbl. was produced from the counties west of the Cincinnati arch, 692,359 bbl. from the 18 new pools opened during the year, and 3,260,765 from the Smith Mills pool, which was discovered in August of 1942. This is an important increase in western Kentucky in spite of the low price of crude, and demonstrates effectively the desire of the industry to cooperate in meeting the increased demands made by the war. Western Kentucky Two deep tests were drilled in the Kentucky portion of the Mississippi Embayment this year. Both were drilled to test the St. Peter. One well, drilled in Marshall County by the Adams Oil and Gas Co., did not encounter any St. Peter sandstone but drilled 650 ft. of formation below the position of the St. Peter and above the true Knox dolomite. The other well, in Ballard County, was reported to have tested the St. Peter and to have been temporarily abandoned at 3069 ft. At this depth the well probably was stopped in about the same formation as the Marshall County well. No accurate information is available on the Ballard County well. Several new producing areas were added to the list of fields in the western Kentucky coal basin, in Daviess, Henderson, McLean, Ohio, Union and Webster Counties. The Smith Mills pool was enlarged and production was found in the McClosky (Ste. Genevieve) in addition to the Cypress sandstone from which much of the earlier production had been obtained. There was some interest during the year in testing the Devonian and Silurian formations in the area south and east of the western Kentucky coal basin. In the fall of 1943, a 15 to 20-bbl. well was drilled in Allen County and two more wells are now being drilled. The production was obtained from within a few feet of the base of the Chattanooga black shale, probably in the upper Silurian. One well in Simpson County was drilled completely through the Silurian section before it was abandoned. Several wells were drilled in Logan, Todd and Christian Counties to test the Devonian where it is thinned by removal of the upper formations before deposition of the Chattanooga shale. None of these wells was successful but several other locations are now being tested. The Silurian thins in like manner on the eastern flank of the coal basin as the crest of the Cincinnati arch is approached, and it is along this thinning edge that such fields as the LeGrande, Logsdon Valley, Magnolia, Bowling Green and the Barren County pools were developed. A number of wells were drilled around these old pools in an effort to extend them, some of which were successful. The wells listed this year in Larue, Hardin, Barren, Hart and Warren Counties were drilled in the search for other such fields.

Jan 1, 1944

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie- Illinois Steel Corporation. Clairton By-Product Coke Plant And Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

ATHOUGH the open-hearth charge contributes CO, CO2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion, the latter being regarded simply as the source of any extra heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were obtained by blowing in air or oxygen, as is the case in the Bessemer converter, then the net heat absorption would be negative, that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with Bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000°F. (1600 to 1650°C.) so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTTNG In the previous chapter it was pointed out that in a typical heat, the fuel furnishes about four million B.t.u. per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner (as is shown later), but it ranges downward from about one million B.t.u., depending not only on the charge but on the manner of calculation. In any event this requirement appears quite small in comparison with the heat furnished by the fuel and invites

Jan 1, 1944

OF THE many categories into which scientific knowledge has been arbitrarily divided, the one which has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. To one who has had no such course or whose auld acquaintance with the subject has all but been forgot, such application is all too often thwarted by the abstruse presentations of the subject found in many of the available textbooks. AS a tool for the control of a complex process involving many chemical reactions, physical chemistry can become very valuable. The specialist who is using this tool for many purposes and perhaps contributing to its development will want to know a great deal more about it than can be included in this book. He will be interested in its history, its accomplishments and limitations, and its applications to many and varied problems. To the steelmaker or metallurgist, however, it is only one of a number of tools that he must use. He is willing to forego the detailed study of its inner workings in order to concentrate upon the development of skill in its application. It is the purpose of this chapter to present a simplified view of physical chemistry as a tool of great potential usefulness. This purpose and the desire for brevity have required the elimination of many of the gadgets with which the tool is usually adorned. It is hoped that this simplification will be conducive to clear understanding. The beginner is urged not to overlook the more extended treatments of the standard textbooks.* He is assured at the same time that the basic tool is sound and serviceable and is guaranteed to give satisfaction if regularly lubricated with common sense. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly

Jan 1, 1944

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By McHenry Mosier

SUMMARY MERCURY is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies.

Jan 1, 1944

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

By Frederick G. Coqueron, Joseph E. Pogue

The purpose of this study is to present the results of a detailed survey of the financial and operating aspects of 30 oil companies comprising a major sample of the American petroleum industry. This review supplements a previous paper entitled "Capital Flow and Capital Formation in the Petroleum Industry, 1934-1941,"a and deals not only with a longer period but also gives new and more revealing analyses of the capital movements and characteristics. The data are gathered from published financial statements of the companies, especially the annual reports to stockholders and Form 10-K to the Securities and Exchange Commission, supplemented by confidential information. The 30 oil companies covered by this study are listed on the leading stock exchanges and for the purpose of analysis are grouped as follows: 9 companiesb engaged principally in crude production, 4 companiesc with production averaging in excess of refinery requirements, and 17 companiesd with refinery throughput in excess of crude production. These samples are sufficiently broad and representative to constitute norms against which individual company performances may be profitably compared. The 30 companies in 1942 produced 54 per cent of the Nation's total output of crude oil and refined 79 per cent of the country's crude run to stills. The financial data apply predominantly to the domestic oil business, although 15 of the companies have investments and operate facilities in foreign countries. The net value of these foreign holdings amounted to 724 million dollars, or 12 per cent, of the combined net assets of the 30 oil companies at December 31, 1942.

Jan 1, 1944

By David R. Mitchell

THE mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during war-time, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for separating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concentrating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435,000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PYRITE PRODUCTION According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

Jan 1, 1944

Jan 1, 1944

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By Harry P. McClintock, Alec M. Crowell

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944