Search Documents

By H. H. Kaveler

A summary of the reservoir engineering and related geologic data on the Schuler field, Union County, Arkansas, is presented here in a manner intended to interest both technical and nontechnical readers. The Cotton Valley formation and the Reynolds oolite are oil-productive formations in the Schuler field, but the Jones sand pool, at a depth of 7500 ft., developed with 146 wells on zo-acre spacing, is the reservoir of principal interest. The Jones sand sandstone reservoir is an anticlinal trap typically gas-drive or depletion type in performance. The core analyses from 88 per cent of the wells drilled, together with drilling time and electric-log data, yield an accurate estimate of the "productive" sand thickness and its areal distribution over the pool. Accurate production statistics, monthly reservoir-pressure surveys, and bottom-hole sample analyses when correlated by the "material-balance equation" show unusually good agreement with that principle. Estimates of oil initially in place made by the material-balance method and the sand-volume method are in good agreement at 116 to rzo million barrels. The reservoir-pressure history of the pool reflects the reaction of a reservoir to production, proration and secondary-recovery practices. The cost of the extensive program of reservoir study in the Jones sand pool has been estimated, in order to emphasize the value derived from such an investment through better understanding of a reservoir's reaction to production practices. Unit operation of 140 of the 146 Jones sand wells made possible an effective unitized gas-injection pressure-maintenance program. Res-ervoir-pressure decline was arrested, natural flow was maintained, and pumping and lease equipment were conserved. An increased ultimate recovery of zo million barrels beyond the estimated 34 million barrels primary recovery is indicated at present. Extension of the Jones sand unit to include the undeveloped Cotton Valley formation will permit additional recovery of otherwise uneconomic reserves of oil through wells no longer required in the Jones sand operations. Introduction The Schuler field comprises approximately 4000 acres in and about sec. 18, T. 18 S., R. 17 W. in west central Union County, Arkansas. Three reservoirs are procluctive of oil and gas: the Cotton Valley formation, the Jones sand, and the Reynolds oolite section of the Smackover limestone. The Jones sand pool is the most important reservoir from an engineering viewpoint. It possesses the traditional and somewhat classic characteristics usually associated with an anticlinal trap. Development and operations have followed the dictates of advanced engineering practices. The pool has attracted attention because of the unusually detailed reservoir data obtained, its interesting production history, and the success of the unitized gas-injection pres-sure-maintenance operation now being carried out. The purpose of this paper is to present a summary of the engineering data relating to the field, with particular reference to the more interesting general applications of

Jan 1, 1944

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

Jan 1, 1944

By H. M. Morse

This report covers the period from Jan. I, 1943 to Dec. 31, 1943. During the year, II2 wells were drilled in Mississippi, as foilows: wildcats drilled and abandoned, 54; wildcats producing oil, 4; oil wells drilled in oil fields, 26; oil wells drilled in fields, dry and abandoned, 10; sulphur-test wells drilled, 14; salt-water-disposal wells, 3; core tests, I. Prospecting Geophysical work in Mississippi during 1943 amounted to 1127 crew weeks, divided as follows: reflection seismograph, 809 weeks; gravity meter, 285; magnotometer, 30; torsion balance, 3. A considerable amount of core drilling was done over a large part of the state. The complete data on this activity are not available at the present time. Salt Domes To date, the following salt domes have been discovered in Mississippi: Midway, Edwards, Glass, Newman, Tatum, Oak-vale, Kings, Halifax, D'Lo, Hazlehurst, Byrd, Leedo, Prentiss, Carson, Moselle, Monticello, Ruth, Keno, Taylorsville. New Oil Fields Lincoln County.—On March 10, 1943, the California Company completed its Smith No. I in sec. 4, T. 7 N., R. 7 E., Lincoln County, as an oil well and produced 29 bbl. of 25" gravity oil in 24 hr. through a fi-in. choke. Two outpost wells have been drilled in this area by the California Company, and both have been abandoned as dry holes. Madison County. —Love Petroleum Co. completed its J. R. Anderson No. 2, sec. 2, T. 8 N., R. I W., Madison County, on Sept. 7, 1943. This well produced 135 bbl. of approximately 30" gravity- oil in 24 hr. through a )/4-in. choke. The production comes from a sand or porosity in the upper part of the Chalk formation of the Cretaceous age. Adams County.—The California Company drilled its National Gasoline Co. of Louisiana No. I in sec. 52, T. 7 N., R. I W., to a total depth of 10,383 ft., and at 10,280 ft, it perforated and obtained gas and a condensate. The well had several showings in the Wilcox of the Eocene age. Several of these showings were tested and the well finally was completed at 5888 ft. on Oct. 6, 1943, producing 44" gravity oil in the second sand in this formation. No other wells were completed in this field during the year. However, a number of wells are contemplated in the near future, and locations have been staked by the California Company. The Oklahoma Pipe Line Co. will market the oil through its pipe-line facilities. Wayne County.—The Gulf Refining Co. drilled Davis No. I in sec. 2, T. 9 N., R. 9 W. in Wayne County. After several stem tests 545'-in. casing was set at 6850 ft. and production was obtained in the so-called Massive Sand of the Lower Tuscaloosa. The well produced 359 bbl. of oil in 24 hr., and it Was completed on Oct. 4, 1943. Other locations have been staked ill this area and probably will be drilled in 1944 by

Jan 1, 1944

E. O?C. Acker Jinzoc Adachi Truman H. Aldrich Walter H. Aldridge Anson W. Allen John H. Allen William R. Appleby W. Lawrence Austin W. S. Ayres David Baker John Henry Banks Henry C. Banon Alonzo F. Bardwell Walter A. Barrows H.C. Bellinger Wm de L. Benedict Robert Bentley John F. Berry Andrew A Blair George D. Blood Charles A. Bohn Walter M. Brodie Elwin F. Brown Fredrick Burbidge H.H. Burden Charles Butters

Jan 1, 1944

By A. A. Smith

The application of indium to bearings was first advocated by C. F. Smsrtl in 1938, for the purpose of inhibiting corrosion of certain bearing alloys. He found that a thin layer of indium plated on the bearing surface and subsequently diffused at elevated temperatures markedly decreased the rate of corrosion in lubricating oils containing organic? acids. Most of his work was done on cadmium-base alloys, although he showed that the treatment was also effective for copper-lead and other; alloys. Since their introduction, indium-treated bearings have found considerable use, particularly in connection with airplane motors.2 Undoubtedly the effectiveness of the indium plate in resisting corrosion depends upon its relative concentration on the bearing surface after the diffusion treatment and after prolonged use at operating temperatures. Some diffusion experiments were made on a number of base metals that had been indium plated, to determine the depth of penetration after heating for reasonably long periods of time. As only the practical aspects were desired, no attempt was made to determine actual diffusion constants. Method Two different series of experiments were carried out to study the diffusion of indium into several base metals. Cast cylinders about one-inch diameter were machined to 0.750-in. diameter, so as to remove all surface imperfections, and final finishing was done with oo sandpaper. The original diameters were very carefully measured with micrometers and then a layer of indium was electrolytically deposited on the cylinders from a sulphate bath.3 In the first series of experiments, about 0.002 in. of indium' was deposited and diffusion, was carried out at 150°C. for a period of 500 hr. in a thermostatically controlled electric oven. After the diffusion period, successive layers were machined from the specimens and analyzed spectro-graphically and chemically—the spectro-graphic examination serving as a guide to determine which layers should be chemically analyzed. Apparently there was some surface oxidation of the indium plate due to the long heat-treatment, which may have had some effect on the diffusion. A1so, the cadmium alloy showed some incipient melting, which probably was caused by the formation of a low-melting eutectic. To eliminate these factors, another series of experiments was carried out by heating in an electrically heated, automatically controlled, oil bath at lower temperature. The preparation of the specimens was the same as before except that a layer of indium 0.0001 in. thick, an amount commonly used commercially on bearings, was deposited on each of the cylinders. Diffusion was carried out at 120°C. for a period of 200

Jan 1, 1944

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By J. F. Myers, F. M. Lewis

THE selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore-in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearce deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table 1 shows a typical analysis of the two ores as well as of the mineral content. []

Jan 1, 1944

By F. Keller, R. H. Brown

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min. is required to drain and dress the furnace hearth, make up the tap hole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays, because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of' charge. Such general considerations are dealt with first. GENERAL CHARGING PRACTICE Charge materials are discussed in detail in Chapter IV; the present chapter is concerned with the charging, melting, and proportioning of the raw materials in the various types of furnace practice. Charging Equipment and Stock Handling. The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment described in Chapter I (see also Fig. 18, page 33). It is generally desirable to charge the scrap about as fast as the physical volume can be got into the furnace. A limiting factor may be the height to which the scrap may be piled in the furnace without deflecting the flame to such an extent that it will impinge on the roof or walls and thus damage the refractories, but light scrap may often be piled up near the roof since the flame usually "cuts it down" rapidly before impingement on any roof area can persist long enough to do appreciable harm. When the nature of the scrap and the handling facilities are adequate to meet the aim of rapid charging, little thought is given to this feature of operation. Unfortunately, at times

Jan 1, 1944

By F. O. Garrabrant

POWER is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt line to a bank of three 3333-kva. Transformers 100/13.8 kv. These transformers arc so designed that with the addition of forced cooling their capacity may be increased 33 1/3 per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200- amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. MINE Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three 250-kva, 13,800/440-volt, single-phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp. motor on the No. 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 100-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft. Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. Under normal operation the one pumping 1200 gal. per min. is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started, and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the pumps restart. On failure of any of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 370 substation is run to the switching station, in which are four15-kv., 600-amp. direct-current solenoid-operated oil circuit breakers. The current for operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1944

Jan 1, 1944

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By Donald M. Liddell

From a commercial standpoint, the only beryllium mineral warranting attention is beryl, 3Be.Al2O3.6SiO2, which is of fairly widespread occurrence. The chief deposits are in Brazil, Argentina, India, Canada and Portugal. When pure this contains about 14 per cent of beryllium oxide. The mineral richest in beryllium is phenacite, (BeO)2SiO2, or beryllium orth-osilicate, which contains 45.55 per cent beryllium oxide when pure, and if anyone is ever fortunate enough to discover a large deposit of it, it will revolutionize beryllium metallurgy. Gadoljnite, zBe0.Fe0.2Yz0~.zSi0~, is also often referred to as a beryllium mineral, though the occurrences are comparatively scant and it is of more interest as a source of yttrium than it is of beryllium. There has been a good deal of talk recently regarding some occurrences of helvite in the United States. Helvite is a complex manganese-iron beryllium silicate and, apart from difficulties that would arise in its treatment because of its compo-sition, the beryllium content of the known deposits is not high. Early Metallurgy The elemcnt beryllium was first isolated by L. N. Vauquelin in 1797.~ He crushed and heated beryl, having the idea that this heating made it more readily amenable to attack by chemicals, and then mixed the mineral with three times its weight of caustic potash and fused the mixture. The melt after cooling was dissolved in hydrochloric acid: dehydrated, and again taken up with hydrochloric acid and filtered to separate the silica. The filtrate was treated with an excess of potassium carbonate and the precipitate after draining was leached with a solution of caustic potash, which dissolved the alumina. The undissolved material was, in Vauquelin's own words, "une terre nouvelle." He dissolved the precipitate with nitric acid and evaporated it to dryness, took up with hydrochloric acid and threw the iron out with potassium hydrosulphide, though he found that to make a complete separation of the iron involved a second treatment. The solution, after throwing out of the iron, had a pronounced sweet taste, and though Vauquelin always speaks of working on "terre du beril" he suggests that the new element should be known as "glucine" (glucinum) from the Greek word for sweet, because of this outstanding property. Vauquelin did considerable work on the comparison of aluminum and beryllium, working out a separation of most of the aluminum based on its precipitation as alum. His work is reviewed at some length, since ordinarily his procedure is incorrectly stated. It will also be recognized by those who have studied beryllium metallurgy that a good many technicians have followed his ideas since, including preheating the beryl before treatment. The fusion with

Jan 1, 1944

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

Jan 1, 1944

By W. A. Alexander, L. M. Pidgeon

Metallic magnesium and similar meta!s near the top of the electromotive series have been commercially produced by the electrolysis of a suitable molten salt. Despite the success of electrolysis, sufficient inherent objections exist to justify the search for a direct reduction method. Such a method would widen the choice of raw materials, relax the rigid electrolytic requirements of raw-material purity, and, by obviating direct current, over simplicity of plant equipment. This paper describes the pilot-plant development of one such method, which has subsequently formed the basis of operation of six commercial plants-—one in Canada and five in the United States. Unlike aluminum, magnesium is volatile at relatively low temperatures. This physical property, which produces its greater inflammability, also offers possibilities of direct reduction that are not available with aluminum. In the basic reaction MgO + X = XO + Mg if X is nonvolatile, the reaction may be forced to the right at high temperatures by the evolution of magnesium vapor, despite the large negative value of the heat of reaction which is almost bound to follow the use of any available commercial reducing agent. The cheapest X, of course, is carbon, but this notable advantage is modified by the production of a volatile oxide CO, so that both Mg and CO are evolved simultaneously. Elaborate devices are required to shock-cool the equilibrium mixture in order to prevent back reaction. At best, a pyrophoric powder is produced, requiring redistillation to provide marketable metal. The practical development of this process, is due to F. Hansgirg, and his methods have recently been given a trial on a grand scale in the plant at Permanente, California, and smaller plants were previously built in Austria, England and Japan. A second class of reducing agents is available, those which produce nonvolatile oxides. When XO and X are relatively nonvolatile, magnesium is the only volatile member of the system. It may be evolved in a simple distillation step and condensed without the formation of powder. Two basic requirements must bc fulfilled in order that such a reaction may proceed: I. The reducing agent when heated to a reasonable temperature in presence of MgO must cause the production of an appreciable equilibrium vapor pressure of magnesium. This magnesium must be removed continuously. z. A supply of heat must be maintained. In order to fulfill the first requirement, operations must be conducted in vacuo or in a stream of Hz. Owing to its greater efficacy and relative safety, vacuum has been employed in the work to be described. The choice of a suitable reducing agent formed the subject of an extensive series

Jan 1, 1944

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By R. S. French

THE purpose of this paper is to present data that have been obtained during the past two years concerning the effects of prior cold-work and temperature and time of anneal upon the recrystallization and grain growth of 70-30 cartridge brass. It was desirable to study certain of these phases so that an accurate picture of the principles of the subject could be shown. The work is not intended to provide explicit annealing data, but to provide material examples that may help to clarify analogous problems concerning this alloy. Specifications often set limitations upon the grain size of annealed materials because of the importance of grain size upon subsequent manufacturing operations. It was, therefore, worth while to study the variables that affect the recrystallized grain size of this material. C. H. Mathewson and A. Phillips,1 W. R. Webster,2 and others have presented annealing characteristic curves of this alloy. A recent typical curve presented by R. S. Pratt3 is shown in Fig. I. The tensile properties and grain sizes are shown as functions of the annealing temperature. Such curves serve as a useful guide in determining the physical properties of annealed material, but as they are made generally under carefully controlled laboratory conditions they do not indicate the performance of metal annealed in a mill muffle, where conditions are different and the amounts of metal require necessarily longer heating times and temperatures. Study of the effect of time and temperature upon grain growth and subsequent recrystallization was made with a coil of metal having the following analysis: 70.04 per cent copper; 0.007 lead; 0.007 iron; 0.00 tin; 0.00 silicon; 0.001 nickel; 0.000 phosphorus; balance zinc. The sample coil was obtained from metal that had been rerolled from hot-rolled mill stock, and was received at 0.228-in. gauge, soft, with a grain size of 0.125 mm. This material was then rolled 43.5 per cent to 0.125-in. gauge and annealed to a 0.053-mm. grain size. In this condition, samples were cut and used in all of the experimental work reported in this paper. TIME The first study was of crystal growth at a constant temperature over a moderate length of time. Material was cut from the stock coil at 0.129-in. size and rolled 75 per cent hard to 0.032-in. gauge. From this piece small samples were cut ½ by 2 in., suitable for grain-size determinations. Twelve samples were placed in an electric furnace uniformly across the width, approximately an inch from the floor, A thermocouple was wired to the center sample, so that the approximate metal temperature could be followed. At various

Jan 1, 1944

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS CHESTER A. FULTON, Chairman CARROLL A. GARNER H. Y. WALKER WALLACE E. PRATT FELIX E: WORMSER PAUL D. MERICA, Consultant FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERIE V. DAVELER, Chairman WILBER JUDSON RUSSELL B. PAUL HENRY KRUMB, Consultant

Jan 1, 1944