Search Documents

By N. A. D. Parlee

THE gas-liquid metal diffusion cell technique1-3 has been used to study the diffusion of nitrogen in Fe-C alloys. The actual apparatus and technique were the same as employed by the authors to study the diffusion of hydrogen in liquid iron.' The diffusion cell' was formed by immersing an alumina tube in a stagnant melt contained in an alumina crucible. The tube (hereafter called absorption tube) contained nitrogen gas at 1 atm and was connected to a sensitive gas-measuring system. The change in the average concentration of nitrogen in the melt in the absorption tube was determined by measuring the rate of absorption of nitrogen in the diffusion cell. Eq. [I], 1-3 derived from the appropriate solution of Fick's second law, was used to examine the data and to calculate chemical diffusion coefficients (D) in situations where the absorption appeared to be controlled by diffusion in the liquid: where V is the stp volume in cu cm, d is the diffusion cell diameter in cm, p, is the density of the melt in g per cu cm, pg is the stp density of nitrogen in g per cu cm, C, is expressed in wt pct, D is in sq cm per sec, and t is in min. According to Eq. [I], a plot of v vs vt should yield a straight line passing through the origin if absorption is controlled by diffusion in the liquid. The slope of this line could be used to determine the value of D under appropriate conditions. As discussed in earlier reports,1,2 the initial thermal expansion of the gas upon immersing the absorption tube distorts the line in the initial stages of a diffusion experiment. However, this is not a serious problem since the slope of V vs 6 plots can be determined from the data points obtained after the initial expansion ceases. The volumes reported on the data plot presented here represent absorption after this thermal expansion ceased. Several preliminary diffusion experiments were attempted with melts of pure iron and with Fe-C alloys containing up to 0.6 pct C. In these cases, no or very little absorption was observed. The only data obtained were for an Fe-C melt which was in addition thoroughly deoxidized by successive hydrogen and vacuum-degassing treatments. These treatments introduced an appreciable amount of aluminum into the melt and reduced its omgen content. The original charge material for this melt contained 0.23 pct s and approximately 0.001 pct &. After repeated hydrogen and vacuum-degassing treatments two diffusion experiments were performed. The analysis of the melt

Jan 1, 1968

By R. C. Gifkins, K. U. Snowden

The value of the index n in power ktivs for the stress sensitivity of minimum creep rale at lead is derived front results drawn from lite literature and from previously unpublished nork on commercial (99.99 pel) and high-purity (99.999 pel) lead polycryslalline and hi crystal specimens. In tests al 0.5Tm (22 to 50'C) for slvesses below 250 psi, n fulls to mily for poly-cr,yslullirle specimens, single crystals, and bicrystals, and toy grain boundary sliding in bicrystals. Between 250 and 500 psi there is a tyansilion range and, for the polycrystalline specimens al least, u high-stress regime for 500 to 1500 psi where n is 5 or 6. These results are such that none of the suggested stress taws can he used to extrapolate to very loir stresses. Meclianisms for deformation in Ike grains and toy grain boundary sliding in the low-strcss regime are outlined. In particular, the mechanism for grain boundary sliding involves sliding controlled by diffusion from tensile to compressire Ledges. predictions based on this model give promising numerical agree-nicul with experiment. II is suggested that the mechanism for grain boundary sliding may he important in other circumstances, e.g., in creep of ceramic materials or superplaslicity, because it can operate with lille or no dislocation aclirity. WhEN the stress dependence of secondary creep rate is represented by a power law the values taken by the stress exponent n are found to vary between 1 and 7, see, c.g., Garofalo.' In Eq. 1 11 u is the applied stress and A a constant. The case for accepting values of v = 1 rests principally upon tests at high temperatures (>0.9Tm) and there have only been isolated tests at lower temperatures (rather than plots of creep rate against stress) for which the creep rates are such that some form of Nabarro-Herring creep with n = 1 is applicable. Hanson5 and Greenwood and cole6 plotted creep rate against stress for tests made in the vicinity of 0.5Tw, and found a "creep yield", so that below a certain low stress the creep rate was linearly related to stress: these observations appear to have been subsequently ignored. Various models have been proposed which agree with a large body of experimental results in which n equals -5 at high stresses (e.g., weertman7 and McLean8). Various alternatives to Eq. [1] have been proposed principally as a means of unifying creep data, but sometimes, it seems, in order to obviate the necessity for assuming a series of regimes of deformation associated with the various values of n; further refer- ence to these will be made in the section on stress laws. This paper calls attention to extensive results which show n = 1 for the creep of lead at room temperature (0.5 T,). RESULTS Fig. 1 is a composite diagram based on figures in the literature6,9,10 with additional results obtained by the present authors and their colleagues11,12 in the course of a number of investigations not directly concerned with stress sensitivity. In Fig. 1 In creep rate is plotted against In stress. The curves show results for two kinds of material. Lead I is of commercial purity (99.99 pct Pb) and lead IT a specially refined material, hydrogen-purified to remove oxygen; it contains 99.999 pct Pb. Curve A is for lead I in polycrystalline form (grain diameter 0.02 to 0.05 cm) at room temperature (22' to 26°C). Curve B1 is for lead I, polycrystalline, tested at 50C. Curve B2 is for lead 11, polycrystalline (grain diameter 0.02 cm), tested at room temperature (22 O- Curves C to F relate to tests made of bicrystals of lead 11: all of the same nominal orientation ("Y" in Ref. 12). Curves C and V are for creep within the component crystals of the bi crystals at 22°C (AB and CD in Fig. 2). Curve E is for creep measured in a gage straddling the boundary, approximately 0.15 mm either side (BC in Fig. 2). Curve F shows rates of grain boundary sliding (as distinct from strain rates in the other curves), obtained by averaging the offsets of six marker lines on the bi-crystal boundaries. The principal feature of the results is that the stress sensitivity falls into two distinct regimes, according to whether the stress is below approximately 250 or above 500 psi (there is a transitional range between 250 and 500 psi). The new result is that below -250 psi two of the curves (A and BI) give a value of n 1, and the other curves also drop below n - 2 to -1.5 but do not extend to low enough stresses to show clear evidence of n 1. At very high stresses the curves tend to give values of n - 6, as previously determined in other investigations. Curve R2 for the high-purity lead in polycrystalline form at room tenlperature almost merges with B, and thus gives new significance to the values for stresses of 150 and 200 psi; previously'3 these points had seemed to fall away from the curve of slope -3, but they now can be seen as almost completing a transition to n = 1. It should be noted that there was originally considerable apparent scatter in the results for the high-purity lead. However, this was found to be associated with annealing conditions or variations in residual content of oxygen and curve B2 was constructed using the highest rate (i .e., the rate for the purest lead) determined for each stress during the course of various investigations over the years: altogether, some forty tests were used in constructing curve R2.

Jan 1, 1968

By C. Norman Cochran

The pllnse diagvam for the NaF-AlF3 system was used to calcutate an ionic model for the NaF-AlF3 system. Assuming an ideal solution,a series of simultaneous equations expressing equilibria be-tween solid and liquid phases at the euleclic, perilec-tic, and melting points were solved for the activities of the ionic species, the dissociation constants, and the entropies and heats of fusion. The calculations suggest the existence of A13F1415 ions in addition to the F-1+AlF6-3 , and AlF4-4 ions previously proposed by others. The calculaled valnes give better agreement with vapor pressures than the previous model without Al3Fl14-5. Additional possible vefinements of the model are proposed. CRYOSCOPIC1 investigations and density data2 for the NaF-A1F3 system have previously been used to study the dissociation mechanism of Na3A1F6 and to derive equilibrium constants for its dissociation to NaF and NaAlF,. Depending primarily on the heat of fusion assumed for cryolite, the dissociation constants ranged between 0.02 and 0.18 from cryoscopic studies, and from 0.09 at 1273°K to 0.16 at 1363°K from density data. In most cases the values were unable to reproduce satisfactorily the experimental liquidus lines very far on the A1F3 side of the Na3A1Fe composition. This suggested the existence of at least one other ionized compound in the melt besides NaA1F4 in the Na3A1F6-A1F3 side of the system. This is assumed to be liquid Na&13F14 (chiolite), which is already established as a stable solid in phase studies of this system. MODEL FOR THE MELT The melt is assumed to be an ideal solution with ion activities equal to anion fractions. The only cation in the model is sodium so that Temkin and simple anionic activities are identical. Although the compounds are completely ionized to Na' and the respective anion in the melt, molecular rather than ionic notation is used throughout this work. The Na3A1Fe is assumed to dissociate to NaA1F4 and NaF as in the former model, and Na&13F14 to dissociate to Na3A1Fe and NaA1F4. Other valid dissociation equilibria can be written involving these four compounds, but all of these can be obtained by combinations of the two described dissociation reactions and, thus, are automatically considered in these calculations. The model allows for no free AlF3 so that compositions for NAIF3 > 0.5 (mole fraction A1F3 on the NaF-A1F3 basis) cannot be treated. The question of the existence of free AlF3 in the melt will be discussed again later. The constants in the model were evaluated from points along the entire known liquidus line of the NaF-A1F3 system. Previous work employed only the liquidus line or densi- ties near the Na3A1F, composition. The liquidus line compositions used in the solution of the model are from unpublished work by Mr. P. A. Foster, Jr., for compositions between the Na3A1F6 melting point and the Na&13F14-A1F3 eutectic, and from the published works of Grjotheim,1 Phillips,3 and Foster4 for the remainder of the system. The relationships used in solving for the desired dissociation constants and heats and entropies of fusion are listed in Table I, and the points along the liquidus line at which each apply are indicated to the right of the relationships. The mole fractions of each of the separate species in the melt are symbolized by N. Relationships [I] and [2] are the respective dissocia-ation constants, Kl and K2, of Na3AIF6 and Na5A13F14 for this model. For simplicity, these constants will be assumed to be independent of temperature. Relationship [3] follows from the assumption of the ideal solution. The expression relating the values of N to the experimental values of NAIf3, is given in Relationship (41. Relationships [5], [6], and [7] each state the equilibrium between a compound in the melt and its pure solid phase for the portion of the liquidus lines where it precipitates. The heats of melting, AH,, and entropies of melting, AS,, used in [5], [6], and [7] are assumed to be independent of temperature. The compositions and temperatures of all five invariant points (two melting points, two eutectics, and one peritectic) along the liquidus lines from NAIF3 = 0 to NAIF3 = 0.5 were employed in the solution. The eutectic and peritectic compositions were particularly useful because each of these is involved in one more equation than other points along the liquidus lines and thus reduces the number of points required to solve for the constants. Also, their use assures that the inflection points in the derived liquidus line will correspond exactly with those on the experimental liquidus line. The total number of equations is 5k1 — 1, where n is the number of experimental composition points used. The number of unknowns is 4n + 5 (4n- 3 values of N, 3 values each of AH, and AS,, and 2 values of K). Thus, six points must be used in the solution to obtain an equal number of equations and unknowns. The one additional required experimental composition was taken on the liquidus line between the Na3A1Fe melting point and the Na3A1F6-Na5A13F14 peritectic. Previous work indicated this was a difficult portion of the curve to fit. The temperature used for the point was 1161°K, the same as for the NaF-Na3A1Fe eutectic. This choice of temperature gave two points with identical NNa3AIF6 values which simplifies the algebraic solution. The second point at this temperature is denoted 1161°'K. PROCEDURE FOR SOLUTION OF EQUATIONS Values were assumed for NNa,AIF and NNaF at the NaF-Na3A1F6 eutectic at 1161°k. By an iterative procedure, the corresponding values for NNa5A13F14 and NNaAlF4 at 1161°K were determined from 131 and 141. A value was assumed for NNaAlF4 at 1161°'K and

Jan 1, 1968

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By V. W. Buys, R. E. Havener

11.3-1. Basic Principles. Communications systems available for application to surface mining operations can be divided into basic categories. These are: 1. Wired systems requiring some type of metallic conductor 2. Nonwired systems, or those commonly referred to as space-radio systems. Under the heading of wired systems, telephones of the ringer type utilizing magnetos were used in the early pit operations. These are still being used in underground mining operations where calling is accomplished by ringing a code made up of short and long rings. While the standard Bell Telephone Systems have not been applied extensively in underground mining, they have been used in open pit operations but have the disadvantage of using multiple pair cables which must be installed and maintained as the mining operations proceed. They have the advantage however, that when a Bell System is installed in a surface mining operation, communication is available not only within the operation but to any point in the world through the facilities of the world-wide Bell Systems. A second type of communication available is the audio system or public address system requiring the use of a special audio cable made up of shielded pairs for the loudspeaker and microphone circuits. Audio systems have one outstanding advantage over most telephone systems in that, with a high-powered amplifier, a paging call can be heard over and above the high ambient noise conditions usually found at a surface mining operation. However, they have the disadvantage of requiring special cable which must be installed and maintained. Another type of wired communication system available for surface mining is that of carrier frequency equipment similar to that used in underground mining operations. In this system, transmission is accomplished by means of a frequency modulated carrier that travels over the underground trolley wire, the rail on which locomotives travel, and adjacent telephone wires.

Jan 1, 1968

By R. H. Maes, R. E. de Strycker, J. J. Jacobs

A simple method, based upow density measurements, has been perfected in order to determine the critical temperature of liquid miscibility gaps. Applied to the Pb-Cu system, it yielded a value of 980"C for the critical tempevature of the miscibility gap in this system. In the Pb-Cu-As system, the immiscibility between lead and coppev evolves towards a miscibility gap be-tween lead and copper arsenides; the liquation temperatures were determined joy different avsenic contents and values up to 1065°C were found. Combining these results with those given by the clzemical analysis of liquid samples taken at dqj.event temperatures, it has been possible to make a cowzplete determination of the liquid miscibility gap in this ternary system. In the Pb-Cu-Fe-As system, a ternary miscibility gap has been discovered; for some compositions, the molten and slowly cooled alloys separated into three layers: an Fe-As alloy, a Cu-As alloy, and a lead-rich layer. ThE Pb-Cu-Fe-As system is of interest for the study of the behavior of speiss or arsenical alloys in the lead blast furnace. The speisses produced in lead metallurgy generally have complex compositions, but they may be considered, in a simplified way, as a mixture of copper, iron, nickel, and cobalt arsenides; there is often an excess of metallic constituants, and lead is also present. Speisses liquate from lead at various temperatures according to their composition; according to industrial experience, iron speisses are already distinctly separated from lead bullion at temperatures of the order of 1100°C, whereas copper speisses only begin to liquate from lead at much lower temperatures, near their solidification points, which were never accurately determined until now. Besides these considerations of practical interest, the present study is of importance for the knowledge of liquid miscibility gaps. Particularly the data of the literature about critical temperatures of liquation are incomplete and present sometimes considerable disparities; a method has been perfected in the present work to determine these temperatures with accuracy. MISCIBILITY GAP OF THE LEAD-COPPER SYSTEM Review of Literature. The generally admitted outline of the Pb-Cu equilibrium diagram is shown by Fig. 1. This figure, with its numerical indications, is taken from the review of Hansen and ~nderko;&apos; compositions are given in weight percent, as will be the case in the remainder of this paper. Between 36 and 87 pct Pb, Pb-Cu alloys separate into two layers, in the liquid state. The critical temperature of liquation has been much disputed in earlier studies, where values up to 1500°C were claimed; but a reliable study of ~ohnen,&apos; based upon differential thermal analysis, gave a value of 990°C; this rather low value was verified by a recent study of Schiirmann and Kaune? based upon thermodynamical properties of the Pb-Cu alloys, which predicted a value of 1002°C. Liquid miscibility gaps were also studied by means of chemical analyses. Satisfactory results were generally obtained with the method consisting in taking samples of the two liquid layers in equilibrium and submitting them to chemical analysis; however, this method becomes delicate near the critical temperature. With this technique, Friedrich and waehlerts ob-

Jan 1, 1968

Jan 1, 1968

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968

By E. T. Turkdogan, J. H. Swisher

The solubility of oxygen in zone-refined iron was determined in the temperature range.from 881" to 1350°C. The solubility in a iron at 881°C ms found to be about 2 to 3 ppm; in y iron, the solubility was found to increase from about 2 to 3 ppm at 950°C to about 25 ppm at 1350°C. The permeability of oxygen in an iron -0.1 pct Al alloy was determined in the y iron range, using an internal oxidation technique. By combining the permeability and solubility data, the diffzisivity of oxygen in y and a iron was calculated. The oxygen diffusivity in solid iron may be s~immarized as follows: 8820 For 6 iron and IN a recent paper, Hepworth, Smith, and Turkdogan1 reported on the solubility, permeability, and diffusivity of oxygen in 6 iron, together with permeability data for oxygen in a iron. In the present investigation, similar measurements were made in the ? phase region. In addition, a solubility measurement was performed in the a phase region to permit calculation of the diffusivity of oxygen in a, iron. References to early work on this subject are given in the previous publication.&apos; EXPERIMENTAL Solubility Measurements. The oxygen solubility was determined by equilibrating cylindrical samples 0.3 in. diam by 14 in. long of zone-refined iron in water vapor-hydrogen gas mixtures. The zone-refined iron was prepared by B. F. Oliver of this laboratory, using an apparatus and technique described elsewhere.2&apos;3 Six zone-melting passes were used to achieve a total impurity level of about 30 ppm. Of this 30 ppm, the combined nickel and cobalt content was about 20 ppm, oxygen was 4 ppm, and all oxidizable impurities less than 1 pprn each. A vertical resistance furnace wound with molybdenum wire was used for the experiments. The temperature was measured before and after each experiment with a Pt/Pt-10 pct Rh thermocouple. In the gas train, flow rates of hydrogen and argon were measured with capillary flow meters, and the resulting mixtures were passed through a column containing 90 pct oxalic acid dihydrate and 10 pct anhydrous oxalic acid to obtain predetermined ratios of H2O to H2. The vapor pressure of H2O above this mixture as a function of temperature is well-known.4 The exit gas was ana- lyzed periodically for H2O, and good agreement (+3 pct) with the calculated composition was obtained. The zone-refined iron specimens were held in the furnace for a sufficient length of time for equilibration, e.g., 18 hr at 1350°C and 1 week at 881°C, then quenched in a brine solution. After removing the surface oxide from the samples by machining, duplicate analyses were obtained by a combined vacuum fusion-infrared method; oxygen analysis was reproducible within 2 ppm. Permeability Measurements. The permeability of oxygen in alloys containing about 0.1 pct A1 was determined by internal oxidation and measurement of the subscale thickness as a function of time. The experimental alloys were prepared by adding aluminum to electrolytic iron (grade 104A plastiron) that had previously been vacuum-carbon deoxidized. The resulting ingots contained about 20 ppm O, 100 pprn C, 40 pprn Si, 50 ppm Mo, 20 ppm P, 20 ppm S, and 20 pprn Zr as the principal impurities. After hot rolling the ingots to 1-in.-thick slabs, specimens were machined from the stock in the form of rectangular plates, 4 by 5 by 2 in. The general procedure for the permeability experiments was the same as those for the solubility measurements. The specimens were cooled in a reducing atmosphere rather than quenched, however, in order to maintain a clean surface for measurement of the sub-scale thickness. This measurement was made on a polished cross section of each specimen, using a microscope with a micrometer stage. The inclusions formed at the lowest temperature 1033°C were too small to be seen with an optical microscope. An electron micrograph showing the size and shape of individual particles is shown in Fig. 1. The dark band in the picture is a boundary between two subgrains. The subscale thickness in these samples was measured with an optical microscope after heavily etching in 2 pct nital, which gave contrast between the subscale and the unoxidized zone.

Jan 1, 1968

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,&apos; a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By J. J. Sense

10.2-1. Equipment Scheduling. In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice for many obvious reasons, principally mechanical conditions, operating conditions, and human nature-this ideal situation is not possible. The cost-conscious organization strives to keep as many pieces of equipment of the fleet working efficiently as much of the work day as possible. Operating efficiency requires the minimum equipment to move the predetermined tonnages in the prescribed period of time. In the case of a shovel-truck operation this would mean the scheduling of the minimum shovel and truck shifts to excavate and transport the necessary tonnage to the processing plant or waste dump. To accomplish this goal, the operator must work from the predetermined production established by the requirements of the plant, stripping ratio, mine plan, etc. This production schedule may be in terms of tons or yards per year, per month, or per hour, but must eventually be translated into tons or yards per ma- chine per unit of time. In this regard, the reader is referred to Sections 8.0, Excavation and Loading, and 9.0, Haulage and Transportation. The trend to larger and faster, and as a result more costly, equipment requires that the operator consider every possibility to keep the equipment operating around the clock, seven days per week. In some areas seven day operation may not be feasible economically, because of premium pay for Sunday work. Mine labor agreements are generally written without premium pay penalties for weekend work, and such scheduling is possible and most often desirable.

Jan 1, 1968

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,&apos; Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer&apos;s suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By Pradeep K. Rohatgi, Clyde M. Adams

Structures obtained on freezing of several hypo-and hypereutectic Al-Cu alloys over a range of solidification rates have been examined. Dendrite spacing, L, increases linearly with solute concentration and with the square root of the inverse freezing rate. The relationship for hypoeutectic alloys is: where rate of change of fraction solid with time, is freezing rate, C is solute concentration, (pct Cu)=1. Mass transport in inter dendritic liquid during solidification is analyzed; the experimental observations suggest maximum concentration differences and constitutional supercooling in the inter dendritic liquid increase with an increase in the solute concentration. The dendrite morphology changes with freezing rate and alloy composition. The dendrites of the a phase are parallel, uniformly spaced plates with slow freezing and rods with rapid freezing. Nonor-thogonal side branching has been observed in phases with cubic and tetragonal structures. Side branches in a dendrites are orthogonal with slow freezing and at 60 deg with rapid freezing. Formation of second-phase envelopes around the Primary phase is also discussed. DENDRITIC structure is characteristic of many types of phase transformation. The most extensively studied so far has been solidification of liquid solutions. chalmersl and coworkers have interpreted the formation of dendrites in terms of the breakdown of a planar interface. Most of the work done concerns itself with the development of an instability at the interface. Little theoretical work has been done quantitatively to relate the parameters of dendritic structure to mass transport in the liquid phase. A few empirical relations based on the experimental2&apos;3 observations exist in the literature. Several workers2 including Brown and Adams1 have studied dendrite spacing in A1-Cu system as a function of solidification variables. In most cases, dendrite spacing has been found to increase linearly with the square root of some parameter proportional to the freezing time. The effect of solute concentration is not clear; some workers report the dendrite spacing increases with solute concentration4 whereas others report vice versa.&apos;&apos;&apos; ~ohatgi&apos; has observed an increase in the spacing between ice dendrites with an increase in solute concentration in water. Tiller has also suggested that dendrite spacing should increase with solute concentration. In the present work dendrite spacing and morphology have been examined as a function of solute concentration and freezing rate. The freezing rate is defined as the fraction of liquid solidified per unit time, dfs/dß?, where f, is the fraction solid and 8 the time. The fastest freezing rate studied was 4550 times the slowest freezing rate. THEORETICAL CONSIDERATIONS It is of interest to analyze the concentration distribution in the liquid phase between growing dendrites during solidification, Fig. 1. Since this distribution is a direct consequence of the rejection of solute by the growing solid, a diffusional process, the concentration gradients increase with the freezing rate. However, when solidification rate is the only variable in a series of experiments, the interdendritic liquid regions become smaller (i.e., the dendrites become more closely spaced) with an increase in freezing rate. The main purpose of the analytical treatment of interdendritic liquid diffusion will be to reveal a tendency for dendrite spacing to decrease with increasing solidification rate in just such a way that the maximum concentration differences developed in the liquid phase are remarkably independent of freezing rate. Two rather different analyses are set forth, one pertaining to the one-dimensional diffusion which obtains in the interdendritic liquid between parallel plate-shaped dendrites, and the other to the cylindrically symmetrical diffusion around rod-shaped dendrites during early stages of solidification. The results of the two analyses are quantitatively similar, correlating dendrite spacing, maximum concentration difference, and freezing rate. First consider the simpler one-dimensional case. Two parallel plate-shaped dendrites are separated by a distance, L, between centers, Fig. 1. Solidification takes place by the thickening of these plates, with solute being rejected into the liquid. It is assumed there is no diffusion in the solid. This thickening process is slow enough and the dendrite spacing small enough that the concentration differences which develop, although interesting and important, are very small (an important assumption which is verified ex-

Jan 1, 1968

By S. Shapiro, G. Krauss

The strutural and cr~stallo~aphic features of the plates of austenite produced by the martensite to aus-tenite or reverse martensitic tramformation have been determined in an Fe-33 wt pct Ni alloy. Micro-focus X-ray techniques and single-surface trace analysis 072 bulk samples yielded two distinct habit planes, (0.174, 0.309, 0.~35)~ and (0.375, 0.545, 0.749jM. The former plane uas the one predorninantly observed and its existence was verified by transn~ission electron microscopy. The orientation relation-ship between the reversed austenite and the parent martensite was approximately the same as the Nishiyamna and other relationships reported for the direct tramformation. Replica and thin-joil obser-vations show that both high densities of tangled dis-locations and occasional twins constitute the fine structure of the reversed austenite. Application of the phenomenological theory to a variant of the predominant habit plane defines an irrational plane and direction for the second shear in accordance with the comnplexity of the fine structure. The shear accompanying the reverse martensitic transformation is at least 0.51, the maximnum value of- the tangent oJ the tilt angle measured on surface replicas. A mechanism relating the fine transformation twins in martensite to the nucleation of reversed austenite of the predominant habit is proposed. The reversal of Fe-Ni martensite takes place both at the edges of martensite plates and in a piecewise fashion within them.&apos; The shear-type nature of the reverse transformation is verified by the surface relief which accompanies both edge-type reversal2 and the fragmentation of plates of martensite&apos; as a result of rapid heating above the A, (austenite start temperature). The orientation relationship between the edge-type reversal product and the parent martensite, as determined by transmission electron microscopy, is reported to be within 4 deg of either the Kurdyumov-Sachs or Nishiyama relationships,&apos; but there is no work at present in the literature relating to the crystallography of the platelike reversed austenite. The fine structure of reversed austenite after heating to 50°C above the Af is reported4 to be composed primarily of tangled and jogged dislocations in concentrations up to 10" per sq cm. A replica investigation of partially reversed Fe-Ni martensites5 corroborates the increase in dislocation density following reversal and presents indications of other possible modes of fine structure. This paper reports on an investigation performed to examine in detail the morphology and crystallography of the plates of reversed austenite and the shear which accompanies their formation in a matrix of Fe-Ni martensite. EXPERIMENTAL PROCEDURE Discs of a high-purity Fe-32.9 wt pct Ni single crystal served as the starting material. The single crystal had been produced in the course of an earlier investigation6 and the carbon content was determined at the time to be 0.006 wt pct. The M,, and the A,, were respectively -120" and 300°C. Partial transformation to martensite was performed at -125°C and reversal of some of the martensite was accomplished by heating in the temperature range 340" to 355°C. Most samples were heated to the reversal temperature by immersion&apos; in a salt bath for 2 min. For surface-relief studies some polished and etched Samples were heated in a tube furnace for ten min in a hydrogen atmosphere maintained over the samples throughout the heating and cooling cycles. Samples were prepared for metallographic examination by electropolishing and etching with an HC1-HNOs-H20 et~hant.~ On one of the surface-relief samples two sets of fiducial scratches were placed on the etched sample by drawing it over a slurry of 0.06 p alumina on a "microclothJ&apos;. The orientations of individual plates of martensite were determined by X-ray analysis. A Rigaku-Denki microbeam X-ray generator in conjunction with a Micro-Laue camera with facility for precision location of the sample in front of the beam was employed for this purpose. The collimator size was 30 p and the specimen to film distance was 5 mm. The Laue photograms were enlarged to an equivalent 3-cm specimen to film distance for analysis. The orientation of each of the plates of martensite was compared to that of the parent austenite and the relationship be -tween the two phases was, in all cases, within a few degrees of those predicted for the direct transformation. The orientation relationship between one of the larger plates of reversed austenite and its parent martensite was determined in a similar manner. The habit plane of the islands of reversed austenite in the X-rayed plates of martensite was determined by a single-surface trace analysis. Each reversal island had with the parent phase one comparatively straight boundary which was presumed to represent the habit plane trace. The pole locus technique7 was applied to traces from six different plates of martensite to determine the indices of the habit plane. A 40-cm stereographic net was employed for this analysis The morphology and fine structure of the reversed austenite were studied by electron microscopy of pre-shadowed direct carbon replicas,5 and the macroscopic shear was evaluated by a two-stage replica technique similar to that employed in electron fractog-

Jan 1, 1968

By E. A. Lowe, C. C. Walden, D. W. Duncan, P. C. Trussell

The industrial importance of bacteriological leaching is finding increasing application in the treatment of low-grade ore and of exhausted mines. Another possible application of bio-leaching is in the extraction of ore concentrates, although here the first uses will likely be for ores that are refractory to conventional metallurgy. Biological leaching studies, which have been in progress for over ten years in this laboratory, are directed towards the more rapid and complete leaching of metals from their sulfides, particularly of copper, zinc, and nickel. The program involves not only laboratory studies, but pilot-plant operations and liaison with mining companies which are underwriting the cost of the investigations. Although the bacterial oxidation of mineral sulfides to the corresponding water-soluble sulfates has been occurring naturally for many centuries, the first documented recovery of solubilized metal from pregnant solution was at the Rio Tinto operation in Spain. At this location leaching variables were studied extensively in an empirical manner some years before the causative bacteria were first isolated from other leaching situations. Documentation of the presence of bacteria in leach waters of the Rio Tinto, Spain, operation was not confirmed until 1962.3 On this continent leaching was pioneered in the early

Jan 1, 1968

By Donald O. Rausch, Robert H. Merrill

12.1 -1. Introduction. Problems concerning slopes in soils and rock generally arise in connection with road cuts and open pit mines. The angle at which a slope will safely stand is of major economic importance to both the road designer and the open pit operator. Stable slopes in soils and rock are evaluated through two fundamental approaches, namely, soil mechanics and rock mechanics. The approach selected to make this evaluation depends upon the material in the slope. For the purposes of this chapter, only slopes totally in soil or totally in rock are considered. By definition, soils are unconsolidated accumulations of solid materials produced by mechanical and chemical disintegration of rocks or the accumulation of sediments (28); rock is defined as the hard, compact, natural materials composing the crust of the earth (10). The basic factors affecting slopes in soil or rock are similar, although rock strengths are orders of magnitude greater than soil strengths. In general, the strength of large masses of soil depends upon the texture of the soil, the particle size, cohesion, and resistance to tensile and shear stress; the strength of large masses of rock depends upon the strength of the rock and the defects, such as faults, fractures or joints, that intersect the rock. Further, some of the defects in rock are cemented or uncemented, and may be filled with materials that are strong or weak compared to the rock. In slopes of either soils or rock, the stability is presumed to be a function of the slope height, slope angle, the size of the excavation, and the stresses imposed on the soil or rock by tectonic and/or gravity forces, earthquakes, or other static or dynamic forces. In addition, both soil and rock slopes are affected by static and dynamic water pressures in the pores of soils or permeable rocks or in the defects in the rock behind the slope. Visual observations of slope failures also indicate that both soil and rock can deteriorate with time, and this deterioration may be caused primarily by weathering (27).

Jan 1, 1968

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By Emerson F. Heald

A systematic study was made of new and old data on chemical activities in Fe-Pt alloys at elevated ternperatuves. Experimental results may be expressed in terms of the excess free energy using Least-squares analysis of the data gave the following values for the constants: for the temperature range 1130° to 1350°C, and tentatively to 155O°C, B = -3.326564 and C = 0.221051; for the temperature range 650" to 850°C, B = -2.555690, C = 1.762735, and D =0.097196. In the study of iron-containing silicate systems, it is sometimes desirable to have a direct experimental measure of the activity of iron in the system. The well-known solubility of iron in platinum, often a headache in experimental work on iron compounds under reducing conditions, can be used to advantage in this respect. If the activity of iron in an Fe-Pt alloy in equilibrium with the silicate is known as a function of the composition of the alloy, chemical analysis of the alloy will give a knowledge of the activity of iron in all of the phases in the system. The present study was undertaken in order to elucidate the characteristics of Fe-Pt alloys as iron activity indicators. This work is intended to tie together some previous work, which may be summarized as follows. Larson and Chipman1 determined the activity of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with calcium oxide-iron oxide-silica melts of known iron activity. Compositions of the resulting alloys were determined by chemical analysis. A similar study was carried out by Taylor and ~uan,&apos; who worked at 1300°C. They brought the Fe-Pt alloys into equilibrium with iron oxide under conditions of known partial pressure of oxygen, and thus, from the work of Darken and ~urr~,~ conditions of known iron activity. Compositions were determined indirectly, by following the change in weight of the sample. Sundaresen et el* used the electromotive force of cells in which the alloy formed one electrode in order to measure the activity of iron in the alloy at 650" and 850°C. These temperatures were chosen to be above and below the first-order phase transition which takes place upon the ordering of Fe3Pt and the second-order transition which occurs upon the ordering of FePt3. EXPERIMENTAL 1) High Temperatures. The starting materials used were thin platinum foil, about 0.002 mm thick, and Fisher Certified reagent ferric oxide, Fez03, which had been heated for 24 hr at 1000°C. An intimate mixture of 80-mesh Fez03 and platinum platelets was placed in a thin platinum foil envelope. The latter was suspended from thin platinum wires in the hot zone of a vertical-tube, platinum-wound furnace of the type described by Muan and ~sborn.~ A capillary gas mixer similar to that used by Darken and Gurry3 was used to prepare a precisely known mixture of carbon dioxide and hydrogen, which was allowed to flow upward through the furnace tube. The partial pressure of oxygen in contact with the sample was thereby fixed at a value which was calculated from the charts prepared by porter? Temperatures were measured with a Pt-10 pct Rh-in-platinum thermocouple, which was calibrated using the melting points of gold (1062 .@C) and diopside, CaMgSizOB (1391.5"C). Temperature control was maintained to within i3"C with a Geophysical Laboratory proportional controller, using the furnace resistance as the sensing element. Samples were quenched by passing a small current through the platinum suspension wires, allowing the sample to drop into a bath of dibutyl phthalate at the bottom of the furnace tube. Prior to chemical analysis the samples were washed with acetone and dried. 2) Chemical Analysis. It proved possible, in almost all cases, to separate the Pt-Fe platelets physically from particles of iron oxide. The platelets were dissolved in a small volume of aqua regia, evaporated to dryness, and redissolved to 0.1 M HC1. In order to determine iron in the platinum alloy potentiometrically, it is necessary first to remove the platinum. A 10-cm column of Amberlite IR-120 cation exchange resin in the hydrogen form provided separation quickly and quantitatively: The mixture of iron and platinum in 0.1 M HC1 was added to the top of the column, and washed with about 100 ml of 0.1 M HC1. Under these conditions, the iron, principally in the form of cations such as FeC1" and FeCl;, is held quantitatively in the uppermost centimeter of the column. The platinum, in the form of anions such as PtC&- , is washed through without being adsorbed. After a qualitative test with stannous chloride indicated all of the platinum was removed, the iron was

Jan 1, 1968

By R. B. Adair, J. S. Browning

The Bureau of Mines conducted laboratory research to determine the applicability of heavy liquid separation to the evaluation of certain mica ores and plant products. After careful standardization of the particular mica ores and associated gangue, accurate analysis of muscovite content could be obtained from results of heavy liquid separation. Where applicable, the method should be particularly suited to the analysis of ores and control of plant operations wherein savings in time would be of considerable advantage. Specifically, there are many instances where a quick plant control method should enable the production of a more uniform grade of mica concentrate. The laboratory use of various heavy liquids for separating minerals of different specific gravities has been recognized for many years.1-8 Sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations. A standard method of analysis for mica in ore samples has not been published or generally accepted by the mica industry. Recently, the U.S. Bureau of Mines investigated methods for analyzing mica by heavy liquid separation. This report has been prepared to make the methods available to others who may need simple, relatively rapid methods of determining the mica content of ores and plant products. The heavy liquid method of mica determination has recently been adopted by one of the major mica producers for evaluating exploration and mill control samples. DESCRIPTION OF THE ORES AND HEAVY LlQLllD The weathered mica pegmatite ores used in the investigation were obtained from commercial mica op erations in Alabama, Georgia, and North Carolina. The major mineral constituents of the ores were muscovite, quartz, kaolin, and minerals of the feldspar group. The ores also contained minor quantities of biotite, limonite, and tourmaline. A comparison of the specific gravities of the major constituents of the ores (muscovite 2.76 +, quartz 2.65, kaolin 2.61, and feldspar 2.57), indicates that an effective separation of muscovite from the other minerals can be made in heavy liquids at a specific

Jan 1, 1968