Search Documents

By T. P. Meloy

Recently, Gilvarry1 has criticized the Gaudin-Meloy2 derivation of the size distribution equation for impact grinding. The criticism states that as the derivation stands it is good for only a long, thin wire being fractured. This paper contains a second derivation in reply to the criticism. Consider a homogeneous solid particle. This particle is broken into fragments by impact. It is assumed that the material resembles galena and that the particles were broken into chunky parallelepipedes which may be treated as cubes. The fragments are now reassembled — as seen in Fig. 1 — and a line is passed through the fractured solid perpendicular to one of its faces. For simplicity, the length of the line segment in the cube is considered to be 1. Fig. 2 represents the line segment in the cube showing the locations of the crack surfaces cutting the line and one point, P, chosen at random on it. The question arises as to what is the probability of the point, P,

Jan 1, 1963

By H. W. Paxton, G. M. Pound

A method is outlined for taking into account variation in chemical potential of both components in evaluating capillary effects at growing interfaces. The results are compared with experiment, and seem to be in reasonably good accord for Widman-statten ferrite growing in austenite. ENERY pointed out that during the steady-state growth of phases with a rather small radius of curvature at their advancing edge capillarity cannot be neglected. By proper application of the Laplace equation a correction must be made to the activity gradients down which diffusion occurs. Subsequent workers have concerned themselves with attempts to evaluate specific cases by the use and modification of the principles laid down by Zener.2-5 To solve the problem in its simplest form it is necessary to assume thermodynamic equilibrium at the interface and to select some criterion which will allocate the available free energy between reversible and irreversible processes. Zener chose to assume that the division should be made such that the new phase grew at the maximum rate. Other workers have used the same2,3 or different assumptions, e.g., maximum rate of free-energy dissipation,4 minimum rate of entropy production.5 Li6 has proposed that the "thermokinetic potential" should be a minimum at steady state. The purpose of this presentation is to note that most prior treatments have considered variations due to capillarity only in the chemical potential of the mobile constituent, and that a more consistent treatment must involve a consideration of the variation of chemical potentials of both solute -and sol- vent in a binary system.* As an example, the way in which this arises for ferrite growing from austenite may be illustrated by reference to Fig. l(a). The line OABC shows a typical variation of carbon activity with composition at one atmosphere pressure (at a transformation temperature below A3). In the tip of a growing ferrite plate with a hemi-cylindricab leading edge of radius ?, the pressure due to capillarity is*

Jan 1, 1963

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By Nicholas J. Grant, A. W. Mullendore

Measurements of grain boundary sliding were made on polycrystal and bicrystal tensile creep specimens of Al-2 pct Mg at 500oand 700oF. Grain and pain boundary orientation factors were studied with respect to their effect on the magnitude and direction of grain boundary sliding. It was concluded that a large part of the observed sliding may be caused by the operation of slip crossing the grain boundaries. Supporting evidence for this model from other investigations is also given. GRAIN boundary sliding in metals during elevated temperature deformation has frequently been thought of as an independent mechanism with its own characteristic stress, temperature, and structure dependence. Further, it is common to regard the grain boundary as the weak link during creep deformation since: 1) the strength of apolycrystallinemetal, as meas-sured by creep rate or rupture life, decreases at\a more rapid rate when sliding comes into action, and 2) grain boundary sliding, as revealed by "boundary darkening" and fold formation is often the first visible deformation. On the other hand, more quantitative observations, in both polycrystals and bicrystals, have shown boundary deformation to be closely related to the over-all deformation of the specimen. The curve of grain boundary contribution to elongation vs time takes a shape similar to that of the total creep curve,',' and the apparent activation energy for sliding appears in most cases to have the same value as that for total creep.3 In order to reconcile these observations, one is left with these possibilities: 1) The grain boundary and grain deformation rates are both controlled by the same rate limiting processes. 2) The rate of sliding is limited by accommodation deformation in the grains. 3) Sliding is the consequence of grain deformation. 4) Grain deformation is dependent on prior grain boundary deformation. Alternatives 2) and 3) would view grain boundary sliding as occurring in series with another deformation process which could be rate controlling. McLean prefers item 3) as the sliding basis,4 where subgrain rotation results from dislocation accumulation in the substructure at the grain boundary. Crussard and Friedel's5 treatment of grain boundary migration considers that dislocations are forced into the grain boundary and are dissociated into dislocations with Burgers' vectors nearly parallel to the grain boundary. The movement of these partial grain boundary dislocations then produces the sliding. The results of this investigation have indicated alternative 3) to be the most appropriate and it is this aspect of grain boundary sliding which will be analyzed. EXPERIMENTAL PROCEDURE Three types of tensile creep tests were employed in this study: (I) A constant load test of one very coarsegrained polycrystalline specimen at 500° F, 3600 psi, 1 pct per/hr strain rate to examine the grain and grain boundary orientation factors in grain boundary sliding. (II) Constant strain rate tests of polycrystalline specimens at 510o and 715o F, 2 pct per/hr strain rate to determine the grain boundary contribution to elongation at very low total strains. (m) Constant strain rate tests of bicrystals of various grain and grain boundary orientations at 500°F, 2 pct per/hr strain rate to obtain further information on the orientation effects in grain boundary sliding. The material used in the tests was a high-purity Al-1'.92 mg alloy, kindly furnished by Alcoa. Its composition is given in Table I. The alloy is a solid solution at the test temperatures. The coarse grained polycrystalline specimen for test (I) was prepared by recrystallizingthe machined specimen, straining it about 1pct intension at room temperature and annealing at 900°F for 8hr. The constant strain rate specimens (11), with an 178 in. sq. by 1/2 in. long gage section, were cut from 1/8 in. thick sheet of cold rolled and annealed (8 hr at 1000oF) material. The latter specimens were supported in a special jig during the milling operations to avoid any bending, and the gage section was subsequently heavily electropolished to remove the cold-worked surface layer. The bicrystals (ID) were machined in the same

Jan 1, 1963

By Toshimi Yamane

The internal friction of cold-worked titanium iso-thermally annealed at temperature below the recrystallization temperature was measured. The internal friction was calculated from the half width of a resonance curve of the specimen which was vibrated transversally by the electromagnetic method. The experimental results were as follows: 1) The specimens annealed for a long time at temperature below the re crystallization temperature after cold working have the strain-amplitude dependent internal friction. 2) The internal friction increased by the cold working was decreased during the isothermal annealing. The reason of decrease of the internal friction is considered to be caused by the annihi-lation of lattice defects. 3) There is a linear relation between logQt-1/Q0-1 and (1/T)2/3 below the recrys-tallization temperature, where Q0-1 is the internal friction standing 24 hr at the room temperature after cold rolling, Qt-1 is the internal friction annealed at T°K for t min. 4) The hardness of the cold-worked titanium does not change by the annealing at 300°C for a long time but decreases by annealing at 400ºand 460°C. METALS, when cold worked, show sharp changes in physical and mechanical properties' The internal friction of cold-worked metals increases sharply and has a maximum value1,2 connected with working de- grees. The increased internal friction of cold-worked metals is recovered by annealing. This phenomenon is the well known effect called Köster effect. The recovery of the internal friction occurs earlier than the changes in tensile properties, hardness, or X-ray diffraction, and is very sensitive to the structure of a metal. The mechanism of the recovery at a temperature lower than the recrystallization temperature is being considered variously by many investigators: there are such views as the annihilation of dislocations by smith,' the rearrangement of dislocations mentioned by Nowick,4 and interaction of dislocation with point defects.5 Smith and Nowick also considered the interaction but it is so difficult for them to explain the rearrangement mechanism systematically, it being not considered a special model; therefore, we do not explain it quantitatively. Experiments measuring the recovery of the internal friction of cold-worked metals were performed by Gordon and Nowick6 on NaCl, and by Smith on copper. In addition, there are many studies, particularly those of measurements on copper by other investigators. There are comparatively many investigations on aluminum and iron which are the cubic system,'-' but only a few on metals of the hexagonal system.10 In view of this, I investigated cph titanium at room temperature and measured the internal friction after annealing isothermally at temperature lower than the recrystallization temperature. SAMPLES AND EXPERIMENTAL METHOD samples for the experiment were cut from a 6-mm titanium plate. The long direction of samples was

Jan 1, 1963

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3'4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,'-' the segregation process became a successful industrial operation.'r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By Paul Gordon

It is shown that equations for grain-boundary migrntion given by Gordon and Vandermeer, based on a theory first advanced quantitatively by Lucke and Detert, satisfactorily explain recent data on both GRAIN boundary migration in recrystallization and in postrecrystallization grain growth has been the subject of extensive studies for many years. Only solute-independent and solute-dependent boundary migration during recrystallization in zone-refined, poly crystalline aluminum, and during grain growth in zone-refined tin. with the advent of zone-refining, however, has it been possible to carry out such studies on high-purity metals, and thus to delineate quantitatively the major effect On the migration rates of very small percentages of dissolved imPurities. Earlier exPerimental work almost invariably gave migration rate parameters which disagreed with theoretical predictions

Jan 1, 1963

By T. Gleason

Problems involved in applying wet scrubbers to gas cleaning coal dust from thermal dryers are reviewed. Careful consideration of all the elements going into a modem coal preparation plant is required in view of the increasing difficulty of applying suitable gas cleaning equipment. This problem arises not only from the presence of finer coals to be handled, but also from the pressures applied by both the general population and the plant operators to improve the standard of gas cleaning performance. The Peabody scrubber is presented by the author as a machine designed to help improve this cleaning operation. Wet scrubbing of fine coal from thermal dryers poses a number of problems in adapting the gas cleaning equipment to the fine particulate matter. Among them are: 1) Dust in gases leaving the thermal dryer cyclones is often extremely fine with high percentages of total dust loading less than 1p in size. 2) Flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulfur or higher. Therefore, comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3) Requirements for residual coal loadings leaving the gas scrubber are continually being lowered, while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend. 4) Installation of a scrubbing system on thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore, the operating costs of gas pressure drop and water requirements must be held to a minimum. We have, then, the basic situation which calls for comparatively high cost stainless steel alloy wet scrubbers, which must be highly effective in removing coal fines particularly in the 0 to 5-p size range. Further, the standards of scrubber performance are continually being raised towards the level where gas discharged from the scrubbers must be essentially free of any coloration due to residual dust. In view of the highly refractive nature of fine coal dust, residual loadings of 0.01 grains per cu ft or less are required to provide a color free discharge gas. In the present specifications under consideration a residual coal loading of 0.05 grains per cu ft would be considered color free, since the discharge gases are saturated in the range of 150°F. The steam plume acts as a masking agent at the point of discharge, and upon dissipation of the 150° saturated vapor stream, the effluent gas stream could be essentially color free. The specification under consideration calls for residual solids loading of 0.05 or less grains per cu ft, given a coal size distribution shown in the basic data in Table I. It is noted that the dust laden coal stream has a size distribution by weight of 33% in the 2 to 5-p size range and 55% in the 0 to 2-p size range. The particle size distribution given in the specifications does not detail the percent by weight less than 1-p in size, and more important, the size distri-

Jan 1, 1963

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By J. B. Stubbins, D. F. Coates, K. L. McRorie

Twenty-two pit slides that occurred in two Canadian open pit mining properties are analyzed. Information on the results of laboratory tests of the rocks and a brief description of the geological environment are also presented. One deduction from the study is that slides seem to be predictable by using established theory. This corroboration indicates that, contrary to normal mining practice, the appropriate slope angle should vary with the height of the wall. In addition, if the general ground water level around an open pit can be reduced, the appropriate slope angles of the walls could then be increased by a determinable amount. The ultimate objective of these investigations is to determine the relationship between the percentage probability of failure of any slope designed with specific strength paraheters. With this relationship it would then be possible to determine optimum slope angles. Because of changes in various economic factors, open pits are now being mined to much greater depths than previously. The need to keep stripping ratios low without endanrrerine.-- lives and equipment provides a strong incentive to determine the maximum practicable wall slopes. Applied research work is currently being conducted to establish the methods for analyzing optimum slopes.

Jan 1, 1963

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By O. Skiredj, J. F. Elliott

It has been necessary to collate the available data on the solubility of graphite in Fe-Si-Mn alloys for a study of slag-metal equilibria in ferromanganese production. That study will be reported later; the collation is reported here. The carbon content of graphite-saturated liquid iron above 1153ºC by Chipman and co-workers1 is: %C= 1.34 + 2.54 x 10~3t(°C) [l] For graphite-saturated manganese above 1322ºC it is: %C = 2.68 + 3.52 x 1CT3 t(°C) [2]

Jan 1, 1963

By C. Dean Starr

The physical basis of the equation correlating electrical conductizlity and temperature coefficient of resistance of solid solution alloys has been inzlestzgated and the nature of the constants evaluated. It is shaun that the same form of correlation is valid irrespective of the magnitude of the temperature coefficient. However, the effect of therma1 expansion and change in resistivity with temberature nust be considered when the magnitude of the temperature coefficient of resistance is near zero. In a comprehensive literature survey conducted at the Armour Research Foundation in 1950, it was found that a linear relationship exists between the electrical conductivity, K, and the temperature coefficient of resistance, a, for solid solution alloys. This was expressed by the equation where B, a constant, depends on the solvent metal but not the solute. A continuing investigation by Hansen, Johnston, and Parks showed this equation was generally appropriate for Cu, Ag, Au, Pd, Pt, and Co base binary solid solution alloys as well as for many ternary alloys of copper over a range of conductivities and temperature coefficient of resistances from 0.02 to 0.60 reciprocal pohm cm and-0.00015to0.004Q per 0 per "C respectively. Eq. [I] was not always valid for alloys that exhibited a change in state (magnetic to nonmagnetic) or for alloys that had a temperature coefficient of resistance near or below zero. For example, in nickel alloys, a simple linear curve as predicted by Eq. [l] was not obtained when the conductivity was plotted against the temperature coefficient of resistance. Hansen suggested that deviations observed were caused by transitions from a ferromagnetic to a nonmagnetic state. Subsequent and more extensive data by ronin on Ni-Mn alloys confirmed Hansen's postulate. While both states independently showed a linear relationship between K and a, the value of B was different for the two states. In some copper and gold base alloys, as well as the platinum and palladium alloys investigated by Hansen, the conductivity did not extrapolate to zero at zero a as demanded by Eq. [I]. This deviation can be readily corrected by simply adding a constant to Eq. [I.] whence Eq. [2] shows the K decreases as a decreases but that K has a positive value when a = 0 which is observed for commercial solid solution alloys as well as the experimental alloys tested by Hansen. While other methods of correlation of electrical properties have been made such as the one by Starr and Wang3 who found a linear relationship between resistivity and temperature coefficient of resistance for Ni-Cr-Al-Cu alloys, the data, in general, can also be correlated by a form of Eq. [2]. Thus, Hansen's empirical equation has considerable merit. The objective of this paper is to determine the physical basis for this equation and to examine the region near zero a in more detail. ELECTRICAL CONDUCTIVITY VS TEMPERATURE COEFFICIENT OF FU3SISTANCE The resistance of a metal or alloy is defined as

Jan 1, 1963

By R. G. Davies

THE effect of ordered structures upon steady state creep has not been extensively studied although it has been demonstrated that the brass,' ie,' and Fe3Al3 superlattices increase the creep resistance. Suzuki and Yamamoto observed an acceleration in the creep rate of Ni3Fe below the critical temperature for order, (T, - 505"), for both the ordered and disordered states, and that the activation energy for creep was independent of the applied stress. They concluded that a dislocation climb creep mechanism was operative down to 300°C which is - 1/3 TM where TM is the absolute melting temperature. This is quite remarkable in that it is usually observed that climb controlled creep in both pure metals and alloys ceases below - 1/2 TM (590" for ie). With this anomaly in mind it was decided to reinvestigate creep in a 75 at. pct Ni-25 at. pct Fe alloy. The creep apparatus and operating conditions have already been decribed. Since Ni-Fe alloys order very slowly, it is possible to have a disordered alloy at a temperature below T,. A long anneal at a temperature just below T, produces considerable long-range order;5 the ordering treatment in the present investigation was 150 hr at 485°C which gives an antiphase domain size of-SOW

Jan 1, 1963

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By S. R. Goodman, Hsun Hu

PREVIOUS investigations on the temperature dependence of rolling texture transition in high-purity silver1'2 and in electrolytic copperS have shown that a brass-type texture is favored at low rolling tem- peratures, whereas a copper-type texture is favored at high rolling temperatures. The transition takes place gradually as a function of the temperature of deformation, and a general correlation between texture transition and stacking-fault frequency or probability exists—a copper-type texture is associated with low stacking-fault frequencies, and a brass-type texture is associated with high stacking-fault frequencies. If the stacking-fault energy is calculated from the stacking-fault frequency and the dislocation density of the specimen, one finds that with low stacking-fault energies a brass-type texture will be developed, and that with high stacking-fault energies the texture will be of the copper-type. These findings are consistent with the idea that the formation of rolling textures in fcc metals may depend on their stacking-fault energy, although results of such nature always involve the ambiguity that a change in the density (or width) of stacking faults produced by deformation at different temperatures may be actually due to a variation in the stress, rather than due to a change in the specific stacking-fault energy per se. It has also been shown that the type of annealing texture depends entirely on the deformation texture. From a copper-type rolling texture, a strong cube texture will be formed upon recrystallization, whereas from a brass-type rolling texture, the annealing texture will be quite different from the cube orientation. Based on these results on texture transition in pure fcc metals, it appeared possible to effect a

Jan 1, 1963

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By E. Martinez

Samples of chrysocolla, a hydrated copper silicate, from several sources were submitted to differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). Pure samples of chrysocolla are difficult to obtain, but comparison of the thermograms revealed that certain reactions occurred in all the samples and it is believed that these are due to chrysocolla. Endothermic reactions occurred at 50' to 175°C, 350° to 650°C, and 980° to 1100°C each of which caused a weight loss. The first was due to loss of absorbed water, the second to a dehydroxyla-tion, and the last to conversion of cupric oxide to cuprous oxide. In addition, two exotherms were detected at 685° to 695°C and 935° to 950°C. Infrared spectra of heated samples indicated the exotherms were due to changes in the Si-O bonds leading to the formation of cristobalite. The results suggest that thermoanalysis may be a more sensitive and reliable method for detection and identification of chrysocolla than X-ray diffraction, infrared spectroscopy, or optical techniques. The recovery of copper from oxide ores has been the subject of much research in recent years. One of the principal oxide copper minerals is chrysocolla, a hydrated copper silicate. The information available indicates that it has widely varying properties depending on the origin of the sample. Chrysocolla usually is found associated with cuprite, malachite, azurite, and native copper. Most of these other minerals are recoverable by present day flotation practice, but chrysocolla is lost in the tailings.1,2 Reagent combinations that are successful in laboratory chrysocolla flotation with ore from one source have been found to be ineffective with another. 3 The copper segregation process offers an altemative to beneficiation of oxide copper ores.4'5 The process is of particular interest in processing ores that cannot be treated by conventional hydrometal-lurgical methods because of high acid consumption.6 Fuller understanding of the properties of chryso- colla may prove of value in the search for improvements in both the flotation and segregation processes. Chrysocolla samples from Arizona, Nevada, Chile, Australia, and South Africa were studied by differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). In addition, a sample from Miami, Ariz., was submitted to X-ray diffraction, infrared spectrophotometry, and surface area determination. EQUlPMENT Differential thermal analysis (DTA) detects, amplifies, and records exothermic-endothermic reactions occurring in a sample as its temperature is raised at a constant rate, usually 10°C per minute. A unit made by the Robert L. Stone Co. was used in this study. The tests can be run if desired with a gas streaming through the sample. A thermobalance records weight losses or gains in a sample as its temperature is raised at a uniform rate. The gravimetric analyses (TGA) were run on a Chevenard thermobalance converted electronically for graphic recording. A heating rate of 5°C per minute up to 1100°C was used in these tests. A Perkin Elmer Infrared Spectrophotometer, Model 221, was used with sodium chloride optics obtaining IR spectra in the 2 to 15 region. A pressed pellet technique with potassium bromide was used in preparing the samples. DESCRIPTION OF SAMPLES Chrysocolla is found in the oxidation zones of copper deposits commonly associated with malachite, azurite, and limonite. It is described as varying in composition and in color from bluish green to brown or black. Inclusions of other minerals are usual so chemical analysis of chrysocolla samples may be suspect. However, it is considered by many to be a solid solution of CuO, SiO2 and H2O with a general formula of CuO.SiO2.2H2O or 2CuO.2SiO2. 3H20. Chukhrov7 has described a sample from the Urals as CU3,5(OH)2 (A1Si3) O10.nH2O and stated that chrysocolla is a montmorillonite-type mineral. On the basis of X-ray analyses, DTA, and infrared spectra of chrysocolla from the Inspiration Mine, Ariz., Sun8 concluded that there was no substantial evidence to classify it as a montmorillonite mineral. Chrysocolla samples from many sources throughout the world were used in this investigation. The following is a brief description of each:

Jan 1, 1963