Search Documents

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By C. H. Li, S. H. Bendel, J. A. Sartell

Small additions of Mg to a 62 Cu-38 Ni alloy reduce the oxidation yates drastically between 500° and 850°C. Metallographic examination of the oxide scale disclosed a continuous network, identified by X-ray diffraction as (Ni, Mg)O solid solutions, located along the former alloy grain boundaries. This network acts as a barrier to diffusion. It is thought to result from the segregation of mg to the alloy grain boundaries. Oxidation occurs preferentially in these regions because of the presence of this more active element. To substantiate these ideas, homogenized alloys ulere oxidized. No oxide network was produced and oxidation rates were the same as for the parent 62 Cu-38 Ni alloy. An interesting aspect of the oxidation of the 62 Cu-38 Ni alloy previously described by the present authors, is the relationship between oxidation kinetics and changes in the microstructure of the oxide.' The oxide scale on these alloys consists of two layers: a thin layer of CuO outside a much thicker layer of Cu20 in which particles of NiO are dispersed. In addition, immediately beneath the oxide-metal interface there is an internally oxidized zone in which NiO particles are dispersed in a copper-rich alloy matrix. Experimental observations on the growth of the individual layers under isothermal conditions have led to the conclusion that the rate-determining step in the oxidation of this alloy is the diffusion of anions through the Cu20 layer. It has been found that this diffusion rate is increased by the recrystallization of the outer CuO layer. Willardson and Gorton have reported that the addition of magnesium to the 62 Cu-38 Ni alloy causes a decrease in the oxidation rate.2 The present investigation was undertaken in order to determine the mechanism by which magnesium additions improve the oxidation resistance of the 62 Cu-38 Ni alloy. EXPERIMENTAL PROCEDURE Fifty-gram ingots of Cu-Ni alloys were prepared by vacuum melting materials of 99.999+ pct purity. These ingots were then remelted in a He atmos- phere and magnesium added in the form of a previously prepared and analyzed Cu-Mg master alloy. This procedure was necessitated by the high reactivity of pure magnesium at high temperatures. The proportion of the alloying elements was adjusted so as to obtain alloys with the desired magnesium content while maintaining a Cu-Ni ratio of 62 :38 by weight. (All alloy compositions will be given in weight percent.) Since it was considered desirable to study the oxidation of only single-phase, solid-solution alloys, it was necessary first to determine the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy. A series of melts with various magnesium contents was made, homogenized by annealing for 48 hr at 975OC, then cooled in the furnace. Metallographic samples were prepared, etched in a potassium dichromate solution and examined at XI500 for the presence of a second phase. The alloys were then chemically analyzed and it was found that the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy was 1 pct Mg. The ingots containing less than 1 pct Mg (0.19, 0.29, 0.58, and 0.87 pct Mg) were cold-rolled down to thicknesses suitable for oxidation experiments and specimens for gravimetric studies were cut to dimensions of 3.0 by 1.5 by 0.05 cm, specimens for inert marker studies, 0.6 by 0.6 by 0.17 cm. These were heat-treated in a protective atmosphere at a temperature (975" C) well above the oxidation temperatures and furnace-cooled to insure structural stability of the alloy during oxidation. Immediately prior to oxidation, the specimens were chemically cleaned by immersion for 1 min in a solution of 2 parts nitric acid, 1 part acetic

Jan 1, 1961

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By P. K. Koh, L. S. Birks, J. M. Siomkajlo

Direct identification in situ of x and a phase precipitates in stainless steel is possible with the electron probe microanalyzer. Although particles in the 1 p size range are too small to yield absolute percent composition, the relative % Crfi Mo ratio can be used to distinguish the two phases with better than 95 pct confidence. Wet chemical analysis of extracted residues gives Cr/Mo ratios in good agreement with electron probe results extrapolated to the 4 to 5 p size range. WHEN stainless steels are subjected to extended heating in the temperature region around 1600°F, precipitation of the brittle 0 or x phases may occur and impair the properties of the material. Identi-

Jan 1, 1961

[Officers JOHN CHIPMAN, President W. R. HIBBARD, JR., Past President C. C. LONG, Vice President T. D. JONES, Treasurer R. W. SHEARMAN, Secretary D. C. JOHNSTON, Assistant Secretary]

Jan 1, 1961

[NORTH AMERICA UNITED STATES ALABAMA Birmingham Cord, Richard H. Dlsmukes, Edward B. Hunter, Robert A. Citronelle Perrin, Huey P. Fairfield Pagel, Herbert Ervin Fairhope Ruffles, William R. Huntsville Eng, Harvard Kelley, Dean W. Waggoner, J. B. Weber, Thomas C. Mobile Hankins, James D. Horner, William L. Petroutson, Peter C. University Cudworth, James R. Jones, Walter B. Mason, William L.]

Jan 1, 1961

By R. W. Shearman, F. Weston Starratt

A new center for mining and metallurgical research is developing at Sterling Forest, N. Y., under the auspices of Union Carbide Corp. Here is to be located the Union Carbide Nuclear and Ore Research Laboratories. In truth, history has repeated itself; the Sterling Forest area in the days of the Revolutionary War, and for many years thereafter, was the mining and metallurgical center of the US. For in these Ramapo hills along the New York-New Jersey border, iron ore was mined, pig lion was cast, and the weapons of war and the plowshares of peace were forged. Before embarking on an historical pilgrimage to yesteryear-a brief description of Sterling Forest. Located in Orange County, N. Y., near Tuxedo, immediately north of the New York-New Jersey State line, and just west of the Erie Railroad and the New York State Thruway, Sterling Forest is approximately 35 mi from New York City. Title was acquired in 1956 from the Harriman family by City Investing Co. Its President, Robert W. Dowling, has established himself as a city planner, having conceived such projects as Pittsburgh's Gateway Center and Philadelphia's Penn Center. A unique, self-contained community -is planned that will contain light industry and centers for research and engineering. Colonies of homes will be interspersed throughout the 20,000 acres of forest land, lakes, and rolling hills. Culture will not be neglected, for Sterling Forest will be the new home for the annual Empire State Music Festival The Sterling Forest Gardens, 125 acres of landscaped woodland and streams, will become the "world's largest permanent floral showplace" The Sterling Forest International Research Building was opened earlier this year, and designed to provide all facilities needed by small growth research companies. The first major company to acquire land to construct research buildings at Sterling Forest is Union Carbide. 1763 ... Discovery of iron ore In turning back the pages of history, a fascinating story can be told of special interest to the metallurgist, the mining engineer, and perhaps even the sociologist. For, where new communities are planned today, older communities had been born, matured, and died. In these hills had lived the. iron miners, the blacksmiths, the lumbermen, the masons, and the teamsters that had given America its start in heavy industry. This was the area where the forests were crisscrossed with many wood roads that brought logs to the charcoal pits, and iron ore to the furnaces. Men make history. Our story brings forth many names of men known as ironmasters, or as industrial leaders-Hasenclever, Faesch, Erskine, Townsend, Ryerson, Parrott, Cooper, Hewitt, Jay Cooke, and Harriman. The name Sterling is derived from a Scotch Lord, the Fifth Earl of Stirling (in its earlier spelling). Lord Stirling was one of seven Englishmen granted a patent of land in the Ramapo hills by Queen Anne in 1707, known as the Cheesecock Patent. He sent an agent, Cornelius Board, to America in 1730, with the express purpose of looking for copper deposits. While he found no copper in his travels up and down the Ramapo Valley, he did find iron ore in two localities: first, in the vicinity of what is now Ringwood, N. J.; second, five miles to the north. There he constructed a forge and furnace at the edge of a lake in 1736, naming the land Stirling Property, after his patron. In 1740, the Ogden family in Newark bought land from Board at Ringwood and began smelting of iron in 1741. The Ringwood story Soon, a genius in the person of Peter Hasenclever appeared on the scene. He was attracted by an advertisement in the New York Mercury for March 5, 1764, in which David Ogden of Newark offered

Jan 1, 1961

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

By W. B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 1, 1961

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

[United States Page 837 Europe Page 881 Canada Page 876 Africa Page 883 Mexico Page 878 Middle East Page 884 West Indies Page 879 Asia Page 884 Central America Page 879 AustraliaPage 885 South America Page879 Pacific Ocean Area Page 886]

Jan 1, 1961

By C. P. Miller

In order to determine the usefulness of geochemical and biogeochemical prospecting for nickel, ten localities representing several types of nickel occurrences were selected as sites from which to collect plant and soil samples. This report covers the investigations in two of the areas. After a brief geologic description of the areas, the author presents details of the experimental tests and resulting data. Conclusions drawn from the studies led to several general guides for further prospecting. In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about three years ago, approximately ten localities, representing several different types of nickel occurrences, were sampled and about 1500 samples of plant and soil were collected. This report will cover briefly the data and results for two areas, and a summary of guides for prospecting. DESCRIPTION OF AREAS SAMPLED One locality is the Red Flats nickel prospect in Curry County, Ore., about six miles southeast of Goldbeach, and the other is the Little Rocky Creek prospect in Stillwater County, southcentral Montana, just southeast of the Benbow chromite mine. The Oregon area is a lateritic-type nickel deposit formed on a nickel-rich serpentinite peridotite complex, similar to the Josephine intrusion in southwestern Oregon. The Montana area is a nickel prospect in norite, peridotite, and related rocks of the Stillwater igneous complex. The Stillwater complex is a series of layered basic and ultrabasic rocks, with a layer of norite-gabbro at the base and a series of peridotites and gabbros above. The nickel in the Oregon deposit occurs in both the peridotite and the overlying soil. A deep lateritic soil is developed locally on the peridotite and serpentinite and constitutes the ore. The average nickel content of the lateritic soil is less than 1 pct, whereas the nickel content of the weathered peridotite is about 1 to 1.5 pct. The nickel occurs as garnierite (Mg, Fe, Ni, Mn)3 (OH)4 (SiA1)2O5 in the soil and in the olivine and pyroxene in the peridotite where it probably substitutes for Fe2+ or Mg2+ in the silicate lattices. Nickel is found in three distinct ways in the Still-water rocks: 1) it is in the olivine and pyroxene minerals in norite, harzburgite, etc.; 2) it occurs as widely disseminated grains of pentlandite-pyr-rhotite, which tend to be concentrated in the lower norite band; and 3) it occurs as discrete bodies of pentlandite-pyrrhotite and chalcopyrite which are localized in the norite zone, close to the contact with the underlying rocks. The nickel content of the norite is probably less than 1 pct, and the nickel content of the pods and lenses within the norite is about 1 pct. PROSPECTING APPROACH Although the areas are different geologically, the approach in prospecting them is fundamentally the same. The procedure is twofold: 1) a rapid reconnaissance survey to outline an area of high nickel content, and 2) a more detailed survey to outline zones of possible ore grade within the area of high nickel. The possible ore at Red Flats is concentrated in the lateritic soil, whereas at Little Rocky Creek it is in the sulfide pods. Both types are surrounded by an area of relatively high nickel content. CHEMICAL ANALYSIS Chemical analyses of nickel were made by a di-methylglyoxime colorimetric test, similar to the standard test for nickel, utilizing concentrated sul-furic acid for extraction. The lower limit of detection for nickel in soil by the method used was about 10 ppm and for nickel in plants about 5 ppm. The relative deviation was about 25 pct. SOIL PROSPECTING General Statements: A summary of the approximate average parts per million of nickel in soil, as compiled from the literature and from my study, is given in Table I. Selected references are given at the end of the paper. Few of the investigators reported the type of extraction or analysis, so the data given may not be strictly comparable to mine, which were made with a sulfuric acid extraction. Any nickel concentration greater than these average values might be considered anomalous, although each area must be studied in relation to the surrounding rocks. Method of Soil Sampling: The soil samples were taken in a zone from 1 in. to 1 ft below the humus layer, and within a 15-ft radius around a station.

Jan 1, 1961

By B. D. Lichter

The lattice parameters of zirconium and zirconium-oxygen solid solutions (hcp) were determined from measurements of back-reflection X-ray photograms obtained at 29°C using a symmetrical focussing camera. The following linear equations between parameters (c,a) in angstrom units (10-8 cm) and atom ratio (m) of oxygen to zirconium were obtained: c = 5.14764 + 0.2077m a =3.23168 + 0.1099m. The linear equations given are valid over the range 0 to 5 at. Pct 0. The accuracy of individual parameter measurements approaches the limiting accuracy determined by the spectral broadening of the incident characteristic radiation, and exceeds the accuracy of previously reported values. THE present work was undertaken in order to determine the lattice parameters of zirconium-oxygen solid solutions with an accuracy that allows quantitative determination of oxygen in zirconium. The results indicate that this is possible if very careful measurements are made, since the parameter change is only a few hundredths of a percent per at. pct 0.1, 2 In the present investigation the desired accuracy was achieved with large-grained samples using a back-reflection focussing camera and maintaining good temperature control during exposure. In addition a digital computer was used for calculation of the parameters by means of an analytical extrapolation.37 Suitable diffraction photograms were obtained from large-grained samples by using a modification of the technique described by Graf and Monteil.5 This consists of simultaneous rotation and oscillation of the specimen about two mutually perpendicular axes during exposure. Whereas, normally the upper limit of grain size is about 50 µ for useable diffraction photograms, this technique allows extending the upper limit of grain-size to exposure of a single crystal. EXPERIMENTAL Preparation of Alloys for X-ray Diffraction—Zir-conium, designated as hafnium-free, Westinghouse "Grade 1," was swaged from l/2-in.-diam crystal bar to 3/8-in.-diam rods. Substantially all of the hydrogen was removed from the zirconium by annealing at 1200°C in a high dynamic vacuum. The rods were then swaged to 0.2 in. diam without intermediate annealing, and 2 in. lengths were cut for alloying with oxygen. Samples for chemical analysis were taken from portions of the rods between each 2 in. length. Chemical analysis of the dehydroge-nated zirconium is given in Table I. Commercial tank oxygen (99.5 pct 0) was condensed in a liquid nitrogen-cooled trap, and part of the condensate was slowly reevaporated into 5-liter storage flasks. Nitrogen remained as a reactive impurity, and the calculated maximum increase in nitrogen content after a 5 at. pct 0 addition to zirconium was 50 ppm by weight. However, chemical analyses of several of the prepared alloys indicated that the maximum increase in nitrogen content was 10 ppm. The storage flasks, a Sieverts-type gas burette and manometer, and associated traps, pumps, and pressure gauges were connected through a glass high-vacuum manifold to comprise the gas addition system. A fused silica tube, connected to the mani-

Jan 1, 1961

By E. J. Pasierb, H. W. Paxton

Mavkers ill a diffusion couple in the iron-chromium system move towards the high chromium side indicating Dcr > DFe at the marker composition. By a combituztion of measurements of D& and D a: a function of composition, this is also shown independently. DFe is calculated as a function of composition. and shown to be in reasonable agreement with measured values by other workers. MEASUREMENTS of marker movements in diffusion couples have been used from time to time to demonstrate that a vacancy or interstitial mechanism may be operative. Since there is a possibility that ring diffusion1 may be operative in chromium, the present experiments are of interest in showing some non-ring mechanism in iron-chromium alloys around the equiatomic composition. EXPERIMENTAL PROCEDURE The movement of markers originally at the interface between 1-in. sq sections of pure Cr (6 mm thick) and outer slabs of 30 Cr-70 Fe alloy was followed as a function of time at temperatures from 1150" to 1425"C, in a Kanthal-wound furnace. Temperature control was +5°C over extended periods. The analyses of these alloys are given in Table I. Selection of suitable markers presented a considerable experimental problem; the eventual solution was to draw quartz rod down to 0.01 cm and seat this in V-grooves 0.01 cm deep on each side of the chromium prior to welding. A preliminary experiment in which the groove was machined in the alloy gave identical results. Welding was accomplished by passing a heavy current through specimens under moderate pressure in a helium atmosphere. This method produced good welds with a planar interface as shown by subsequent metallo-graphic investigation. Any markers which did not adequately fill their groove and showed subsequent contamination from the atmosphere during heat treatment were not considered reliable. The composite sample was ground and metal-lographically polished on the four sides perpendicular to the interface. Fiducial marks (deep milled slots) were made outside the diffusion zone to check on total volume change. All necessary measurements were made on a metallograph reading to +0.0005 cm. The samples were wrapped in tantalum foil and given diffusion anneals for times to 200 hr in carefully purified dry hydrogen in a sealed McDanel porcelain tube. Chromium-zirconium chips were introduced near the specimen as an additional getter. The specimens were cooled relatively slowly after the diffusion anneal to preserve the McDanel tube but no significant error in effective time at temperature was thereby introduced. At least 1 mm was ground off the surface before measurements were taken. It was observed that the grain size following short diffusion anneals was several mm and was appreciably larger in the 30 Cr alloy than in the pure Cr. No significant grain boundary penetration was present as indicated by the etch limit. The results are presented in the next section. Measurements of D were made by standard sectioning techniques with chemical analysis. Machining difficulties limited the

Jan 1, 1961

By R. T. Hukki

This paper presents a preliminary analysis of the fundamental relationship between the net energy used and the respective product size throughout the entire range of sizes covered by crushing and grinding, and an attempt to find a sensible correlation between the existing theories. Walker, Lewis, McAdams, and Gilliland' have given the following differential equation of a general form for comminution: dE = -C§ [1] where E is the net energy required per unit weight in a certain process of comminution; x is the factor indicating the fineness of the product; n is the exponent indicating the order of the process, and C is a constant related with the material, units chosen, etc. H exponent n in the above equation is replaced by numerical figures 2, 1, and 1 1/2, the integrated form of the general equation leads to the well known fundamental theories represented by the law of von Rittinger,' law of Kick, and the third theory of comminution by Bond, respectively. The total net energies (E) from infinite feed size to a product of size x are as follows: The net energy required in a certain process of comminution is proportional to the new surface developed according to the law of von Rittinger, to the weight or size of the bodies treated according to the law of Kick, and to the length of the new cracks formed which initiate breakage according to the theory and explanation by Bond. On a logarithmic paper, where particle size is presented on the abscissa and energy consumption on the ordinate (see Fig. 21, all three relationships are represented by straight lines. The slope m of the line according to the law of von Rittinger is equal to -1.0; of Kick, 0; and of Bond, -0.5. Experimental evidence in favor of the law of Rittinger has been presented, e.g., by Gross and zimmerley5 on quartz crushed in a drop weight crusher and evaluated for surface by the method of dissolution, by Dean on magnetite crushed by a similar method and evaluated for surface by the determination of coersive force, by piret7 and co-workers on a group of minerals crushed again by a similar method as well as by compression and evaluated for surface by permeability and gas adsorption methods, and by schellinger8 on a group of minerals ground in a calorimetric ball mill and evaluated for surface by gas adsorption. Experimental evidence in favor of the law of Kick seems to be scant in the field of comminution. On the other hand, in the field of mechanical engineering Kick's law seems to be of fundamental nature in processes such as cutting, pressing, shaping, and rolling of metallic substances. Experimental evidence in favor of the third theory has been provided by Bond." To a large extent, data are based on the vast amount of grindability tests performed in the laboratories of Allis-Chalmers Manufacturing Co. In addition to the devoted proponents of one or the other of the basic theories listed above, certain investigators have indicated that one of the theories might be applied for a certain range of sizes, while another theory might be used for other sizes. In a discussion of a paper by Bond," Dobie" presented a statement at the International Mineral Dressing Congress in London (1952) indicating that 1) for large particles, the law of Kick was approximately correct; 2) for finer particles, von Rittinger's suggestion was nearer to the truth; and 3) Bond's new

Jan 1, 1961

By S. E. Hasko

It is the purpose of this note to report the crystal-lographic data for nine new B5A compounds* having the Cu5Ca structure, with A a rare earth and B a transition element, Co, Ni or Cu. In previous papers, some magnetic data1 and preparation and crystallo-graphic data2 for other B5A compounds having the same structure have been reported. Crystallographic data for these compounds are shown in Tables I and 11. These results are in agreement with others of this series reported previously by Wernick and ~eller.' The abnormally large atomic volume of Yb metal3 is not manifested in Ni,Yb, when one compares it with the compounds reported here and the data of reference 2. This is not true for the compound YbAl,, having the cubic Laves structure (MgCuz), to be discussed in other papers.4'5 Thus, it appears that Yb has a valence of 3; i.e., the 2 s and Id electrons are lost to the conduction band.4'5 Lattice constants for four of these compounds prepared by levitation melting have been reported by Nassau, Cherry, and wallace.' The lattice constants

Jan 1, 1961

[Admissions: B. M. Gottlieb, Chairman Edmond F. Egan K. Marshall Fagin John S. Fuller Edward E. Monteith T. A. Pollard Howard J. Ritts, Jr. Kenneth W. Robbins Harold E. Wright Advertising and Exhibits: Bernard F. Klein, Chairman Bob Diggs Brown R. E. Howard H. M. Krause, Jr. R. G. Parker Mrs. Evelyn R. Robertson]

Jan 1, 1961