Search Documents

By Henry F. Heblby

HOW often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days1' indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer's day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. The Sources of Atmospheric PolLution The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is prob- ably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominantly dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh Indicative of the stupendous quantities of fuel that are employed in this industrial area's economy, the following (Table I) taken from the U. S. Census (1940) may be of interest. In tonnage consumed in the area, the figures are equally impressive: Annual Tons oF Coal Metallurgical Industries.... 35,000,000 to 40,000,000 Commercial Installations (Pgh.)................. 1,500,000 Domestic hand-fired) (Pgh.)................. 750,000 An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, uti-mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1949

By M. R. Goldick

The Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5½-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mcchanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. Ore Treated Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopy-rite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (go pct minus-zoo mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1949

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

Jan 1, 1949

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By L. S. Darken

It has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernstl in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and FuossZ with results which have recently been confirmed experimentally by Harned and Nuttall. This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author,4,5 who pointed out4 that "for a system of more than two components it.is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepti- cism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley" in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion of acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 10500 C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1949

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah, The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 in. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements, They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics' have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I. 03 -1.06 Acid number.................. 6-8 Softening point, mercury method 160°-165°C Iodine valus (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residua] coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction CO., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1949

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months' to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By A. Lee Barrett

The Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting as a part of this report the second of a series of maintenance cost comparisons. The committee's purpose is to assemble maintenance costs on all equipment connected with mechanical operations at the face of coal mining and to arrange these costs by districts so that comparisons can be made between districts and within districts. The committee, this year, sent 35 questionnaires to representative coal companies who either reported last year or had advised specifically of the inability to report to last year's questionnaire primarily because of limited time. The response to the questionnaire this year as not as good as last year, only 20 of the 35 selected companies returning a completed questionnaire. This year's data have been compiled and combined with last year's data to present a comparison of the 1945 and 1946 costs of loading machines, shortwall cutting machines, universal cutting machines, service locomotives, shuttle cars, and mine cars. The same tabulation by districts is used as was used for 1945. As was indicated by last year's report there is considerable variation in the in cost of mining machinery in the various coal mining districts and due to this high variability it was not felt practical to attempt to arrive at weighted averages. Consequently, all average figures used in this report are straight averages. An analysis was made of companies reporting both this year and last year in an attempt to determine the trend in maintenance costs for different classes of equipment. Ten representative companies are used in this computation. Table I shows the average cost for 1945 and 1946. It is felt that the negative trend in the maintenance cost of universal cutting machines probably represents the effect of the purchase of a relatively large number of new machines in 1946 with little maintenance cost appearing during the first Year of operation. The grand total figure indicates an upward trend amounting to plus 18.7 pet. However, this figure is viewed with some suspicion because of the effect of the universal cutters decreasing maintenance cost and it is concluded that direct application of percentage increase should be made to types of equipment. In Table 2 covering maintenance costs of various types of mining equipment for 1945 and 1946 the results obtained in Table I indicating trends were applied to those

Jan 1, 1949

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By W. N. Lacey, C. G. Yundt, B. H. Sage, J. S. Billheimer

As a part of a general investigation of the separation of bitumen from hydrocarbon mixtures a study was made of a restricted quaternary system composed of methane, decane, tetralin, and bitumen. The work was limited to a pressure of 8000 psi, a temperature of 220 °F, and to a fixed relative proportion of decane, tetralin, and bitumen. The measurements permitted the determination of the distribution of these components in each of the fluid phases. It was not possible to distinguish a second liquid phase in the course of these measurements. Gas-liquid equilibrium "constants" of each of the components were found to vary markedly with the composition of the system while temperature and pressure remained fixed. INTRODUCTION The separation of bitumen frorn naturally occurring hydrocarbon mixtures has been of importance for a number of years in the production of petroleum, especially in the California area. The deposition of this material from crude oils was noted in earlier studies of the solubility of natural gas in crude oil.¹,²,3 Studies of the separation of bitumen from crude oils from the Greeley and Santa Fe Springs fields were carried out."." The behavior of these systems appeared complex and studies of two restricted ternary systems involving mixtures of n-pentane, tetralin, and bitumen,&apos; and of decane, tetralin; and hitumen, confirmed this belief. Reviews of the literature pertaining to the separation of bitumen from naturally occuring and refined hydrocarbons are available." The important effect of methane in the separation of bitu- men from naturally occurring hydrocarbon mixtures was apparent from the earlier studies and for that reason it appeared desirable to investigate a restricted quarternary system involving mixtures of methane. decane, tetralin, and bitumen; data concerning the behavior of mixtures of decane. tetralin. and bitumen having already been obtained.V his study was restricted to a pressure of 8000 psi," a temperatue of 220° F, and fixed relative proportions of bitumen, decane. and tetralin. This composite constituent, hereinafter designated as the less volatile constituent, was made up of 0.0455 weight fraction bitumen. 0.0909 weight fraction decane, and 0.8636 weight fraction tetralin. The experimental method involved bringing together mixtures of methane and the less volatile constituent in varying proportions in a constant volume container at the pressure and temperature indicated above. The composition of each of the phases was determined and from this the extent of the separation of bitumen was established. MATERIALS The bitumen used in this investigation was obtained from the same stocks employed in earlier studies. The crude material from the North Coles Levee field was stored in the laboratory] in a closed drum for a period of five years. Several samples from this stock were subjected to refining operations which were described earlier,&apos; and every effort was made to follow the same procedure in all cases. It was necessary to prepare supplies of bitumen for this investigation at two rather widely different times. These materials have been identified as samples 1 and 2. The composition of the crude bitumen after it was washed with n-pentane at room temperature

Jan 1, 1949

26. G. H. S. Price, S. V. Williams, and G. J.O. Garrard: Heavy alloy, its production. properties and uses. Metal Industry (1941) 599 354s 372. 394. 27. R. Kieffer and W. Hotop: p. 320 of ref 12. 28. F. R. Hensel. E. I. Larsen, and E. F. Swazy: Physical properties of metal compositions with a refractory metal base. Chap. 42, 483, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 29. R. Kieffer and W. Hotop: p. 290 of ref. 12. 30. H. Freundlich: Kapillarchemie. 211 (1923) Leipzig. 31. W. Ostwald: Zisch. f. Phys. Chemie. (1900) 34, 503. 32. G. A. Hulett: Zisch. f. Phys. Chemie. (1901) 37. 385; and (1904) 47, 357. 33. J C. Chaston: Discussion to Price, Smithells and Williams, p. 257 of ref. 4. 34. W. Dawihl: Untersuchungen ueber die Vorgaenge bei der Abnuetzung von Hartmetallwerkzeugen. Ztsch. f. techn. Phys. (1940) 21 336. 35. W. Dawihl and J. Hinnueber: Ueber den Aufbau der Hartmetallegierungen. Kol-loidzlsch. (1943) 104, 233. 36. F. Skaupy: Dispersoidchemische und verwandte Gesichtspunkte bei Sinter-hartmetallen. Kolloidzlsch. (1942) 98, 92; and (1943) 102, 269. 37. F. C. Kellcy: Cemented tantalum car- bide tools. Trans. ASST (1932) 19, 233. 38. E. W. Engle: Cemented carbides. Chap. 39, 436, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 39. W. Dawihl: Zlsch. f. Melallkunde. (1940) 32, 320. 40. P. M. McKenna: Tool Materials (Ce- mented Carbides). Chap. 40. 454. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 41. G. A. Meerson. G. L. Sverev, B. Y. Osinovskaja: Zhurnal Prikladnoi Khimii. (1930) 139 66. 42. A. G. Metcalfe: The mutual solid solubility of Tunesten Carbide and Titanium carbide- Metal Trealmenl (1946) 13, 127. 43. P. Schwarzkopf: Powder Metallurgy. 196-201 and 354-356 (1947) New York. 44. H. Burden: The manipulation and sintering of hard-metals. Special Rep. No. 38, p. 78. Iron and Steel Inst.. 1947. London. 45. W. D. Jones: Principles of powder metal- lurgy. 150. (1937) London. 46. J. E. Drapeau: Sintering of powdered copper-tin mixtures. Chap. 32. 332, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 47. H. E. Hall: Sintering of copper and tin powder. Metals and Alloys (1939) 10, 297. 48. F. Sauerwald: Present status of powder metallurgy. -.Melallwirlschafl. (1941) 20, 649. 671. 49. H. L. Wain: Powder metallurgy; influence of some processing variables on the properties of sintered bronze. Report ACA-25. Australian Council for Aeronautics (1946) Melbourne. 50. S. L. Hoyt: Constitution of copper-tin alloys. Metals Handhook, 1364. (1939) Cleveland. 51. T. Ishikawa: Studies on the interdiffusion of copper, tin and graphite powders. Nippon Kinzoku Gakkai-Si (1937) I, 226. 52. A. Carter and A. G. Metcalfe. The struc- ture of porous bronze bearings. Special Rep. No. 38, p. 99. Iron and Stecl Inst. (1947) London. 53. R. P. Koehring: Sintering atmospheres for production purposes. Chap. 25, 278. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 54. C. G. Goetzel: Some properties of sintcred and hotpressed copper tin compacts. Trans. AIME (1945) 161, 569. 55. J. W. Lennox: The production of some non ferrous engineering components by powder metallurgy. Special Rep. No. 38. p. 174. Iron and Steel Inst., 1947, London. . P. Duwez and H. E. Martens: The power metallurgy of porous metals and alloys having a controlled porosity. TP 2343, Metals Tech. April 1948. This volume. p. 848. 57. E. A. Owen and L. Pickup: X-ray study of the interdiffusion of copper and zinc. Proc. Royal Soc., London, Series A. (1935) 149, 283. 58. C. G. Goetzel: Sintered and hotpressed compacts of copper-zinc powder. Chap. 34. 352, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 98, R. Chadwick. E. R. Broadfield, and S. F. Pugh: Observations on the pressing. sintering, and properties of iron-copper powder mixtures. Special Rep. No. 38, p. 151, Iron and Steel Inst. (1947) London. 60. A. Squire: The properties of iron-copper compacts. Watertown Arsenal Lab. Rep. WAL No. 67101. 61. F. C. Kelley: Properties of sintered iron- comer uowder. Iron Age (Aug. 15. 193) 158 57. 62. G. H. Howe: Sinterinn of Alnico. Iron Age (Jan. 11. 1940) 14.5, 27. 63. R. Kieffer and W. Hotop: p. 359 of ref. 12. 64. W. Hotop: Permanent magnets from sintered iron-nickel-aluminum. Stahl und Eisen (1941) 61, 1105. 65. P. R. Kalischer: Some experiments in the production of aluminum-nickel-iron alloys by powder metallurgy. Trans. AIME (1941) 145, 369. 66. S. J. Garvin: Production of sintered per- manent magnets. Special Rep. NO. 38. p. 67. Iron and Steel Inst. 1947, London. 67. F. C. Kelley: Discussion to P. R. Kalischer. p. 375 of ref. 65. 68. R. Kieffer and W. Hotop: p. 357 of ret, 12. 69. C. H. Howe: Sintered alnico. Chapter 48, 530, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. Powder Metallurgy Seminar (C. G. Goetzel presiding) C. G. Goetzel—The seminar has been opened by a man who has been active in the field for over fourteen years and has made, since then, some major contributions to the advancement of the art. After having been associated with the Moraine Products Division of General Motors Corporation for over ten

Jan 1, 1949

By W. D. Steele, S. D. Brady

The Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains minable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon-galia Co. thence south and southwest across the state to Wayne Co. near Hunt-ington. The Pittsburgh coal is also minable in the Upper Potomac region but is now practically exhausted there. The total minable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13¼ billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio River as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern West Virginia District comprising Wetzel, Mon-ongalia, Marion, Preston, Harrison, Dodd-ridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 1880 (when the Monongahela River Railroad, now B. & 0. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgan-town and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Mononga-hela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of minable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. Economic Importance The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1949

By Gieskieng, D. H.

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely different materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected

Jan 1, 1949

Jan 1, 1949

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By James G. Crawford

Correlation Of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the petroleum engineer. The water in each producing zone tends to have diagnostic characteristics by which it can be distinguished from every other water above or below that zone in that immediate vicinity. Representative analyses of oil-field waters from producing oil and gas fields in the Rocky Mountain region are included, and the diagnostic characteristics are discussed briefly. It is concluded that the generally dilute nature of Rocky Mountain oilfield waters is a result of dilution by meteoric waters, and that there is no relationship between presence or absence of commercial oil and the character of water in a structure. Introduction The study of waters associated With oil and gas began more than 50 years ago and has been well recognized by operators, engineers, and geologists for about 30 years. It appears unnecessary at this time to recite the history of oil-field water analysis; suffice to say that it has proved its worth many times to the production engineer suddenly confronted with water problems in producing oil and gas wells. Chemists and geologists have studied the possible origin of these waters and as Yet the subject is unsolved in many important phases. There are both local and regional problems connected with the explanation of concentrations and character- istics peculiar to each field, each subsurface zone and each province. Criteria useful in postulating the Occurrence of oil Or gas in One province completely fail when applied to another, and data carefully prepared and analyzed from one field may be actually misleading when applied to another. Correlation of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the engineer. The concentrations and characteristics of the waters are essential to the engineers and geologists making interpretations of electric logs in this region. The behavior of water under conditions of reservoir temperature and pressure is dependent to a great degree upon its concentration and characteristics, and thus important to the reservoir engineer. With the advent of secondary recovery methods in the Rocky Mountain region the characteristics and treatment of water will become increasingly important. Premises upon which Correlation Is Based A brief review of the geochemical history of oil-field waters will suffice to present the premises upon which correlations of the waters are based. Sedimentary rocks which are now stratified were first sediments in seas, lakes and streams. These sediments were filled interstitially with connate water. With burial the sediments were compressed arid consolidated, integrated and indurated into bed rock and much of the connate water was dispelled. Following the formation of bed rock the strata were sub-

Jan 1, 1949

By Reynold Q. Shotts

The small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive ac-in of coke in the form of &apos;&apos;trees,, or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of labora- tories1,2,3,4,5 are one method of approach to the problem Of selecting stoker coals- As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that Others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simp1e measure Of the tendency Of a a to form coke in a fuel bed. Although possessing all Of the disadvantages Of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects Of swelling properties upon combustion.7 Ostborg, Limbacherand Sherman, have shown that the test can Predict, roughly, the tendency Of coke to accumulate in the fuel bed Of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1949

By P. A. Beck

In the course of work on grain growth in high purity aluminum a simple optical method was developed for detecting the presence or absence of preferred orientation in annealed specimens. The specimens were prepared by grinding, polishing and "deep etching." The etching reagent used for high purity aluminum has been described.* The resulting etch pits produced selective

Jan 1, 1949