Search Documents

By W. R. Hibbard

The term lineage was first introduced by Buergerl to denote dendritic branches, grown from a crystal nucleus during solidification from the liquid, with imper- fections in alignment of the order of 10 : to 10-4 cm. These imperfections are associated with distortions of the dendrites caused by the subsequent solidification of the inter-dendritic filling and are illustrated in Fig I. Buerger etched zinc single crystals made by the Bridgman3 method to develop this dendritic pattern and show lineage microscopically. Since maximum crystal growth in face-centered cubic metals occurs along the [IT] directions,2 lineage would appear in copper as small deviations of dendritic branches from these directions. Elam4 and others5"8 reported etching effects resulting from coring along the cube face traces of various copper alloy crystals. These traces were used by Samans8 to orient single crystals. Williamson9 noted a "lined structure (in alpha brass single crystals) consisting of an ordered arrangement of etch pits" which were probably traces of {IOO} planes but somewhat uncertain because they were never straight (that is, apparently lineage). Greningerl1 described the distortion and multiplicity of Laue spots in back reflection X ray photograms of copper single crystals showing lineage. The present investigation -includes metal-lographic, X ray, and property studies of lineage in large grain and single crystal specimens of copper. Preparation of Specimens specilnens 10 in. long 35 1/2 in. diam of oxygen-free copper (o.F.H.c.) (99.985 pet) were' melted vertically in graphite crucibles under an atmosphere of commercial nitrogen purified through a gas train including sulfuric acid, potassium chloride, magnesium chiorate, hot copper chips and phosphorus pentoxide. After a temperature of 1200°C had been maintained for 1/2 hr, the furnace was turned off and the specimens cooled at a rate of about 150°c an hour' This method of direct solidification was used by Greningerlo to produce single crystals with marked lineage and in this investigation produced a fair yield of single crystal specimens in

Jan 1, 1949

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

Jan 1, 1949

Jan 1, 1949

By Howard I. Smith

POTASH is of prime importance as a plant food and is also widely used in industry. The term "potash was applied to a crude pearlash obtained by evaporating, in iron pots, solutions leached from plant ashes. Later it included caustic potash obtained by treating pot ashes with lime, and now it is applied generally to various compounds of potassium used by agriculture and industry. Herein it applies to the theoretical equivalent in potassium oxide (K20)--a compound never found in nature or manufactured in commerce but generally used as a common denominator for comparison of all potassium compounds. Potash was made from plant ashes at an early date, but potassium in mineral form was not noted until 1797, when it was identified in leucite.3 The importance to plant life of potash in the soil was first recognized by von Liebig3 and his published reference thereto appeared in 1840. In 1843, potash was discovered in the brine of a well drilled for salt near Stassfurt. HISTORY OF THE AMERICAN POTASH INDUSTRY Among the colonists reaching Virginia in 1608 were men from Poland skilled in making potash from wood ashes19 and records show that the production of potash was begun in other colonies also, soon after their establishment. The American product entered the trade in 1635, and at various times since that date the production of potash for industry has been subsidized by the Government or protected by tariffs. The production of potash from wood ashes reached its peak in 1825. Beginning in 1823, a cheaper product, sodium carbonate, made by the Leblanc process, was substituted for much of the potash used in industry. Production rapidly declined after the Civil War, when the forests most productive of potash had become depleted and labor had become

Jan 1, 1949

Jan 1, 1949

Jan 1, 1949

By W. Bradley, R. G. Hall

This paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer &apos;0 the Bradley &apos;lining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a a kiln at the same end—that is, of course, the upper end&apos; This is as opposed to "countercurrent firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. Early References The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,l its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver ... is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and fies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake county, California, The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank, Reed and Sulphur Bank ranked respectively Nth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: of there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of ... the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away, as its richness and value were not

Jan 1, 1949

By R. F. Evans, J. M. Avert

Much has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this opera- tion is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft.— apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. Production of Magnesia from Dolomite In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime [CaO)., value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or advantageous. Essentially, the process is based upon the following series of reactions:

Jan 1, 1949

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

By M. R. Geer, H. F. Yancey

With the exception of pneumatic processes and a few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral-dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficia-tion process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and elsewhere, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment lor many years, and more recently driers employing centrifugal force have gained in popularity.&apos; A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal—a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. Object and Scope of Investigation Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it On coal &apos;lurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1949

By C. R. Sandberg, T. A. Pollard, E. B. Elfrink

This paper presents an evaluation of compressibility factor data and a discussion of their application to the estimation of gas reserves. A correlation is presented which provides compressibility factors for use in both two-phase and single-phase hydrocarbon systems. Accuracies comparable to those obtained previously for single-phase systems only can be expected. A simple means of predicting the presence or absence of a liquid phase in a condensate system of known composition is illustrated. The correlation is based on 1,030 compressibility determinations from 21 hydrocarbon samples taken from eight oil fields. Of the data used, 75 per cent were from California, 15 per cent were from the Mid-Continent area, and 10 per cent were from South America. The average numerical deviation of the experimental data from this compressibility chart is 1.22 per cent. Charts and tables are included and discussed which illustrate the errors involved through the misuse or nonuse of compressibility factors in estimates of gas-in-place. INTRODUCTION The compressibility factor is a coefficient which expresses the deviation of a gas of given composition from the Perfect Gas Laws. A factor such as this is necessary in any calculation involving volumes of gaseous mixtures, and finds extensive application in the estimation of natural gas and condensate reserves. It is used in the decline curve, the volumetric, and the material balance methods of gas reserves estimation. The behavior of gases at high pressures has been investigated extensively in recent years and considerable data have been assembled on the compressibility characteristics of a number of gases. Notable among the investigators of high pressure gas relationships are Kvalnes and Caddya, Kay" Sage and Laceys, and Brown, Standing" and Katz4. Other contributors are Smith and Watson, Roland and Kaveler&apos;, and Stevens and Vance". The data on compressibility factors assembled by these investigators have been presented and correlated in numerous ways; particularly noteworthy is the method first presented by Kay5 which relates compressibility factor "Z" to pseudo-reduced temperature and Pseudo-reduced pressure. Other investigators have used this empirical relationship successfully and numerous charts covering a large number of gases have been constructed on this basis. It is the purpose of this paper to evaluate compressibility factor data and to illustrate the importance of their proper use in the estimation of gas-in-place for both gas and condensate reservoirs. EVALUATION OF COMPRESSIBILITY FACTOR DATA The compressibility chart presented by Standing, Katz, Brown and Holcomb in 1941 is probably the most recent and reliable chart for natural gases. The reliability of the Katz chart has been investigated by the writers for a fairly large number of gases (single-phase) in the pressure range from 500 to 10,000 psia and temperature range from 80 to 400°F. A summary of this comparison is presented in Table I. The numerical average deviation of the chart compressibility factors from the experimental compressibility factors is 1.05 per cent, and the algebraic deviation is -0.28 per cent. The Katz correlation appears to be quite accurate for single-phase hydrocarbon systems. It was based on single-phase systems and does not necessarily provide a means of accurately predicting the behavior of two-phase systems which might be encountered in condensate work. Data published recently by Sage and Oldsl&apos; have enlarged the knowledge of phase behavior in condensate systems by covering extensively the Compressibilities of systems in the two-phase as well as single-phase regions for a wide range of temperatures, pressures and gas-oil ratios. An evaluation of these data indicates that conditions can arise, especially in condensate systems having fairly low gas-oil ratios, in which two phases occur and the usual gaseous compressibility factors do not accurately apply. The measured PVT data of Sage and Olds covering two-phase systems have been correlated with additional such data from the Mid-Continent area and South America; these are presented in Fig. 1. This chart is the result of 1,030 compressibility* determinations from 21 hydrocarbon samples taken from eight oil and condensate fields. Of the data used, 74.75 per cent were from California, 15.45 per cent were from the Mid-Continent area, and 9.80 per cent were from South America. The chart construction is based on the original

Jan 1, 1949

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man&apos;s first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

By C. R. Dale

The need for instruments to measure the movement of fluids and gas in wells has been recognized by engineers for many years. Information regarding flow in the producing interval has a direct bearing on completion practices in new wells and also provides information on the production characteristics of the well. Many hours of engineering time are spent in planning and completing wells but knowledge as to whether or not the original planning has produced the desired results has not always been complete. Many questions such as the following often arise: Why is it that two wells are completed under supposedly identical conditions, yet one well is a good one and the other is a poor one? Are the sands that look the best on the electric log contributing to the production? These and many other conditions in the producing well need to be under- stood in order to develop more efficient production practices and to improve on methods of completing new wells. It is the purpose of this paper to briefly describe one type of instrument, outline the methods of running the equipment and show the results of surveys made under various conditions. With an understanding of the use of this type of survey its importance can be evaluated in relation to the problems encountered by the operator. DESCRIPTION OF INSTRUMENT The instrument is a velocity recorder employing a clock-controlled 16mm film for recording the rpm of an extremely sensitive rotor which is rotated by the flow of fluids or gas in a well. The helical-vaned rotor and shaft, weighing one-half of one ounce are an integral unit exposed to the well fluids and are the only moving parts not enclosed in the fluid-tight housing. No packing or fluid seal of these parts is necessary and the shaft is mounted top and bottom on special jeweled bearings. Fig. A is the lower part of the instrument showing rotor and shaft with the protecting housing sleeve removed. The rpm of the rotor is recorded on the moving film by a combination electrical and optical system. The record is a series of dashes on the film, each dash and space representing twenty (20) revolutions of the rotor. (Film record of survey made in California well showing station recordings at various depths.) As the movement of the film is controlled by the clock the number of dashes and spaces in one minute of film travel represents the rpm of the rotor. The range of the instrument is from 0 to 2,500 rprn. The barrel or housing is 1-11/16 in. OD and seven feet long. Various types of expanding fluid traps are attached to the lower end of the instrument to direct the flow through the 1 in. orifice containing the rotor. The fluid trap for upward flow is shown in Figs. B and C. This assembly consists of eight arms with light spring

Jan 1, 1949

By E. H. Lancaster, M. E. Mitchell

A MUD-conditioning program found to be very effective for drilling and completion operations on routine field wells requiring relatively short drilling time involves a moderate alkaline-tannate-bentonite treatment resulting in an ultimate filtration rate of 10.0 cc or less (API test). Mud weight schedules are planned from pressure information on completed wells in producing reservoirs and drill-stem test data obtained on other zones not being produced at present. In general, terminal mud viscosities average 45 sec (Marsh). This value has been found to be sufficient to remove cuttings from the well bore on the average well, with the slush pumps in general use on the rigs. On field wells requiring drilling times in excess of approximately 30 days, an alkaline-tannate-lime-bentonite treatment has been effective in maintaining desirable viscosities and filtration rates with a substantial reduction in chemical costs. This system has shown particular advantage on heavily weighted muds and those with abnormal flow-line temperatures. For the most part, the chemical treatment utilized in wildcat drilling follows closely the program used on field wells, depending on depth and duration of drilling operations. Wildcat mud programs are planned from information available from various geologic and operational sources, taking into consideration the possibility of encountering mud problems of a special nature in the wildcat area. Careful planning of wildcat mud pro- grams has proved to have definite value in avoiding most serious mud problems. An analysis and recommended treatment are presented on several special. mud problems which have been encountered in the area in the past. Those problems discussed are lost circulation, blowouts, sloughing shale, excessive chloride contamination, sulphate contamination, and prevention and correction of cement contamination. Introduction Drilling-mud control in the Southwest Texas area, in general, does not involve the multiplicity of problems encountered in other coastal areas. For instance, it is rare that a mixture of problems such as lost circulation, abnormal pressure, severe sloughing shale, and others, occurs on one well within close enough limits in vertical depth not to be taken care of by a sensible casing program, together with a relatively clear-cut mud program. There are conditions such as the fairly widespread occurrence of abnormal pressure in the lower Frio and Vicksburg zones, and the tendency for sloughing shale in the Jackson section which make for rather expensive mud control. However, the availability of fairly accurate geologic and operational information makes possible a reasonable degree of standardization on mud treatment over a relatively large area. It may be said that, over most of this area where drilling is currently in progress, the natural mud made is very poor in quality, but responds readily to moderate chemical treatment to yield very good wall-building characteristics. AS far as field development drilling is concerned, the mud engineer&apos;s principal job, once the routine treatment best

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20&apos;s before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By G. Derge, W. Peifer, J. H. Richards

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,&apos; and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By Robert C. Stephenson

Large deposits of titaniferous magnetite occur associated with anorthosite and gabbro in the Lake Sanford area, Essex County, New York. The ore, gabbro, and anortbosite show consanguineous relations. Anorthosite grades through gabbroic anortbosite into gabbro but is locally intruded by gabbro. Structural and petrographic evidence suggests that gabbro was differentiated from anorthosite by filter pressing. Field and laboratory study of ore occurrences indicates that an ore residuum concentrated in the gabbro through magmatic segregation&apos; by normal crystallization and flowage. Ore occurs as bands which grade into gabbro, and also as large masses which replace anorthosite. Ore in the gabbro is finer grained and richer in ilmenite than ore in anorthosite. Introduction The Lake Sanford area lies in the heart of the Adirondack Mountains, in the southeast portion of the Santanoni Quadrangle (Fig. I), and there are four ore bodies in the area immediately surrounding Lake Sanford. The area lies 30 miles by highway from the railroad at North Creek. The deposits were discovered in 1826, and from then until 1858 iron was produced in small quantities. They were idle from 1858 to 1906. Between 1906 and 1913, extensive development work was carried on. These early attempts to produce iron ore were thwarted by transportation difficulties and by the titanium content of the ore, which, ironically, has been the element responsible for the present development. In 1941 the National Lead Co., Titanium Division, developed the Sanford Hill ore body and is now producing ilmenite and magnetite concentrates.18 The Defense Plant Corporation is extending the railroad to the property from North Creek and is building a sintering plant to treat the magnetite concentrate. Investigations OF the Deposits* Early studies of the Lake Sanford titaniferous magnetite deposits were made by Emmons in 1842,l2 by Kemp, in 1897-98&apos;0 and by Newland in 1908.22 Singewald26 and Osborne23 considered these deposits along with numerous other titaniferous magnetite deposits in 1913 and 1928, respectively. None of these reports entailed a detailed study of the ore occurrence in this area. The present study was begun in 1940. Seven months were spent in the field, and considerable time was spent in labora-

Jan 1, 1949