Search Documents

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors' Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By B. D. Cullity

INTRODUCTION THIS investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy-the thermoelectric efficiency-has been discussed by Telkes1 in a recent review of the subject. She gives the thermoelectric efficiency as: [ ] For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of properties. BISMUTH-SELENIUM ALLOYS Work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson,2 who gives the diagram reproduced in Fig I. There are two intermediate phases in this system, BiSe and Bi2Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedral crystal

Jan 1, 1948

By Nelson Severinghaus

Following the end of hostilities of World War 11, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, One near Camak, One near Lithonia and one at Stockbridge. All have had excess fines Or in in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling Of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed 'tone is generally sold with a a narrow margin Of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. By-products of Granite Dimension Stone It sometimes becomes difficult to differentiate between main product and byproduct. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of Uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I), They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1948

By Robert Steinitz

SOFT iron parts for magnetic applications, particularly pole shoes, constitute a major portion of the ferrous products of powder metallurgy. The residual pores in pressed and sintered parts reduce values such as the magnetic permeability but service experience extended over a number [ ] of years has proven beyond doubt that in many instances the lower density of powder parts is not prohibitive to their use m replacement of machined magnetic parts The. magnetic requirements for pole shoes particularly the permeability, vary within wide limits, especially with the relative size of the air gap in the finished assembly. The overall permeability of an assembly, µ, is given by the formula [ ] where µm is the permeability of the core material, l the total length of the magnetic path, and a the length of the air gap. Fig 1 shows the variation of the overall permeability with the permeability of the core material, calculated according to Eq I for an air gap of 1 pct of the total length of the magnetic circuit. It is readily recognized that to use core materials hav-

Jan 1, 1948

By E. V. Potter, H. C. Lukens

INTRODUCTION IN general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation' the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. APPARATUS The apparatus used in these investigations is essentially the same as that used in the manganese work' and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in ' gas volume are measured by volume gauge C which is essentially another mercury manometer in which . the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 61 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within ± 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. METHOD The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient time intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1948

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for ' military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,' but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By J. B. Newkirk, A. H. Geisler

INTRODUCTION CERTAIN of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some permanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems offer for study over the usual in which an intermetallic compound is formed are many: I. Since the precipitate has the same crystal structure as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be expected to have the same orientation. 3. Small disregistry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from o to 100 pct* thus permitting wide freedom for the study of the effect of composition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1,2 The two have the same [ao] parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for Cu-Ni-Co alloys because of the similarity in constitution but this had not been demonstrated. The present investigation was conducted on a Cu-Ni-Co alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established 4,5 however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system was chosen for a comprehensive investiga-

Jan 1, 1948

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By James A. Barr

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By D. J. McAdam, G. W. Geil, R. W. Mebs

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,&apos;-&apos;&apos; the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals &apos;&apos;should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture&apos; In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By L. L. Gray, D. W. Reed, F. Morgan

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown&apos; The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

Jan 1, 1948

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,&apos; as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948

By William H. Baer, George M. Carlton, Blake M. Loring

IT is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen.1,2,3 Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). EXPERIMENTAL PROCEDURE The material for this investigation consisted of extruded rods 1 ¼ to 1 ½ in. in diam. The chemical compositions were as follows: [ ] The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0-015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to ±3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements.

Jan 1, 1948

By C. E. McCarthy, A. George Stern, Stanley J. Green

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world&apos;s largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By John G. Koert, Koert D. Burnham, John G. Broughton

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.&apos; Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation&apos;s pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3&apos;4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

Jan 1, 1948

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948