Search Documents

An established method exists for the computation of rope lifetimes for shaft hoisting applications in the mining industry. In an earlier study, during the 1990s, an initial comparison of the calculated and actual rope life for various types of hoisting plants showed reasonably good correlation. In the meantime the calculation method has been developed further. The rotation behaviour of the rope during hoisting and the effects of multilayer spooling on drums are now considered in the assessment of expected rope lifetimes. The ability to determine an estimate of rope life in advance is particularly useful for mining companies. Such analysis allows them to predict the effects of rope choice in their particular application and thereby reduce the total cost of rope ownership. Such calculation techniques also allow designers of winding plants to identify aspects of the hoisting configuration that may negatively affect rope life. Often small (low-cost) changes, like increasing the diameter of head sheaves, can result in considerable improvements in rope performance. This paper describes the extended lifetime calculation method and gives further examples of the comparison between actual and calculated rope lives for operational double-drum mine hoists.

Jan 1, 2005

The results of the washing of coal are often presented by using Partition Curves. By analogy, it is possible to express the results of screening by using similar partition curves. As in the coal washing processes, this method determines the accuracy of screening and is also suitable for different separations depending on the difference in size distribu- tion. This method compares the effectiveness of two screening operations and forecasts the performances.

Jan 1, 1984

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By A L. Zawadski, B G. Putland

"This paper discusses a method to build a calibrated comminution circuit model, using historic operating data and blend information that is useful for forecasting and optimising plant performance, as well as evaluating expansion opportunities. A preferred method for building a calibrated power-based comminution model is discussed and justified based on two case studies, offering low-cost and effective strategies to utilise existing information for the maximum possible benefit.The first example is the Lefa Gold Mine located in Guinea, West Africa operating a semi-autogenous grinding (SAG) and ball milling circuit with recycle crushing (SABC). Daily blend information and operating data was utilised to build and calibrate a power-based model of the comminution circuit. The least squares regression method was used to solve the SAG mill specific energy requirement and the operating work index (Wio) for each individual ore type. The calibrated model was used to evaluate expansion strategies to sustain throughput at higher proportions of fresh ore based on the proposed life-of-mine schedule.The second example is the Ok Tedi Copper-Gold Mine in Papua New Guinea operating a SAG and ball milling circuit (SAB). The circuit limitation would often shift between the SAG mill and the ball mill due to variable ore characteristics and feed blend. Typical SAG mill relief strategies, such as recycle crushing or secondary crushing, required significant capital expenditure and the potential throughput benefit would vary depending on ore type, making economic justification difficult. Daily blend information and operating data was used to build and calibrate a power-based model of the comminution circuit to identify ore types that might benefit from higher blast intensities to increase fines content, thus relieving the SAG mill limitation and increasing overall throughput without a major capital investment.Citation:Zawadski, A L and Putland, B G, 2016. Calibrating Comminution Models Using Operating Data to Forecast and Optimise Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 17–26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By N L. Turner, D J. Robinson, A J. McFarlane, N M. Chapman, L L. Kuhar, R L. Meakin, R Martin

A number of geometallurgical tests have been developed within the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project, an interdisciplinary collaborative research project involving four research groups and over 20 global mineral companies. Researchers at the Commonwealth Scientific and Industrial Research Organisation (CSIRO) have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. One of the focus areas has been the development of a leaching scheme for determination of the mineralogical deportment of copper in a large number of samples for geometallurgical applications.Various leaching schemes have been used over the last 20 years to identify the mineralogical deportment of copper. Typically, weak sulfuric acid and cyanide are used to target copper oxides and æsecondaryÆ copper sulfide minerals, covellite, chalcocite and bornite, respectively. Residual copper is assigned to chalcopyrite and/or bornite. Adaptations of this scheme have included the use of a weak organic acid to target oxides or ferric sulfate to target secondary copper sulfides. Testing of the weak acid/cyanide scheme in the GeMIII project using head and residue QEMSCAN mineralogical data analysed with a statistically reliable comparison method indicated that the inferred mineralogical deportment from various leaches could differ markedly from the theoretical or assumed value. Based on this initial work, test development and leach tests on samples from multiple sites has resulted in the development of a scheme to target copper oxides, chalcocite, covellite, bornite and chalcopyrite. This paper presents results from leach tests conducted on a large sample suite from two pits in a Cu-Au ore deposit with results calibrated using mineral liberation analyser (MLA) mineralogical analysis. This study has assisted in the development of a protocol for determining the mineralogical deportment of copper in a large number of samples for geometallurgical applications.CITATION:Kuhar, L L, McFarlane, A J, Chapman, N M, Meakin, R L, Martin, R, Turner, N L and Robinson, D J, 2013. Calibration and testing of a geometallurgical leaching protocol for determining copper mineralogical deportment, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 177-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

By P K. M Mazzoni, D Frantois-Bong

This paper aims to show alternatives to the estimation methods used for finding the parameters in GyÆs well known model for sampling variance in the case of particulate materials. Many experiments designed for gathering data on the sampling variance for specific mineral deposits allow the experimenter to use approximations in the calculation of the parameters of the mathematical model involved, which sometimes can be very useful. However, there are some instances where approximations lead to biased estimates of the parameters, and consequently, lead to errors in the establishment of the sampling protocol and treatment of quality control data. In the present work, an alternative is presented for computing the parameter values based in any experimental set up, without the need for any simplification. The method was derived using the method of least squares and evaluations are made using the usual tools in this kind of methodology: residual analysis and evaluation of the fit by means of a plot of calculated versus experimental variances. With the aid of these tools, one can better evaluate the structure of the experimental errors in such applications, and the adherence to the proposed model. In addition, it is possible to perform hypothesis testing for the equality of different sampling procedures in terms of sampling variance. The full mathematical details are given, together with an algorithm for applying the method, which can be implemented easily using any computer language. An illustration of the method is shown, considering the international work done in ISO/TC 102. This example is a determination of the minimum sample mass to be collected in iron ore shipments, in order to achieve a specified sampling precision.

Jan 1, 2005

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By Keele R. A

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

By B Maybee

In underground mine planning, many potentially value-eroding decisions are made due to a lack of time and proper evaluation practices. The information required for mine planning decisions goes beyond external sources of uncertainty that are recognised by typical evaluation techniques used in the mining industry, to include technical factors (eg mine development layout) and the ability of a mineral extraction project to achieve its anticipated production levels. Due to the individual characteristics that define underground mining projects, each will exhibit a different risk profile, and thus advanced optimisation and evaluation techniques are required to capture this information.As underground mine planning tools become more sophisticated, mine planners have the capacity to investigate numerous mine sequencing options to identify the best strategy for a given project, creating higher value for shareholders. This paper describes a risk-based evaluation methodology (RbEM) that accounts for financial and technical risk in the evaluation of underground mining projects. While the use of the RbEM has been described in previous works, no benchmarking of the benefits that can be realised from a change in those decisions that are made early in the process has been undertaken. To show the benefits that can be achieved from using the RbEM, this paper updates a case study to which the RbEM was applied, and takes a retrospective look at whether additional value would have been gained by following the strategic recommendation of the RbEM versus a typical optimisation exercise that aims to maximise the net present value.CITATION:Maybee, B, 2012. Can a risk-based evaluation provide a more valuable mine design?, in Proceedings Project Evaluation 2012 , pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By R Valenta, J Owen, D Kemp, E Lebre, G Corder, J Thomas

Numerous recent analyses have shown that future demand for a broad range of critical commodities is unlikely to be met by new discoveries and recycling alone. The only practical alternative source to address this shortfall comes from orebodies which are currently either uneconomic or inaccessible. A common assumption is that a simple rise in commodity price will render these deposits economic. The mining industry has a long history of innovation allowing economic production from increasingly low grade and technically challenging orebodies. Industry “roadmaps” have been produced on a regular basis, with the aim of identifying future innovations which will allow this progression to continue. At the same time, there have been relatively few systematic analyses of the actual range of challenges facing undeveloped orebodies. The aim of this study is to analyse the mix of challenges faced by a group of undeveloped orebodies in order to better understand the relative importance and necessity of innovations applicable to the deposits, with the ultimate aim of determining the relative value and impact of possible innovations to the economic viability of those deposits. CITATION: Valenta, R, Lebre, E, Kemp, D, Owen, J, Corder, G and Thomas, J, 2018. Can a simple price-rise unlock complex copper orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 71–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By H von Blottnitz, A C. Keith

The influence of the life of a mine extends beyond its immediate vicinity both in geographic and temporal terms. Decisions around mine approvals are generally made based on economics, for the mine owner and immediate environmental and social impacts by governments and communities. The value from life-of-mine planning can also be viewed in a holistic frame across the entire value chain from mine to product user. This research examines the Carmichael Coal Mine in light of the holistic benefits and impacts along its value chain from the mine to relieving the lot of energy poor in India.CITATION:Keith, A C and von Blottnitz, H, 2016. Can Australian coal alleviate energy poverty in India – a case study, in Proceedings Life-of-Mine 2016 Conference , pp 52–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R T. A MacGillivray, S B. Curtis

Bacteriophage (phage) are viruses that infect bacteria. Protein coatings on the surface of the phage particle can be genetically engineered so that they bind to inorganic molecules. The filamentous phage particle is about 930 nanometres in length and 6.5 nanometres in diameter and consists of a single-stranded molecule of DNA surrounded by five different coat protein molecules denoted P3, P6, P7, P8 and P9. Peptide sequences in the P3 coat protein that bind to sphalerite and chalcopyrite have been identified. The binding is selective; phage with specific P3 peptide sequences bind to minerals but do not bind to silica or to pyrite. Two peptide sequences in the P8 coat protein that bind selectively to chalcopyrite and pyrite have also been identified. The amino acids in the P8 binding sequences are hydrophilic and thus a coating of a mineral particle with phage having these peptide sequences may render the particle hydrophilic. Experiments are underway to confirm this. Phage are relatively easy to grow and are not living organisms requiring an energy source to maintain life. Phage can also tolerate a range of pH and temperatures. Given this, and the ability to indentify phage coat proteins that bind selectively to a variety of inorganic molecules, phage have the potential to be useful tools in mineral processing and waste treatment.

Jan 1, 2008

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

By P W. Cleary, M D. Sinnott

Cross-belt cutters are commonly used for sampling coal. They are generally cheaper than falling-stream cutters, particularly when a cutter must be retrofitted. The major mechanisms thought most likely to lead to sample bias are being investigated by discrete element modelling (DEM) in a project funded through the Australian Coal Association Research Program. This paper describes a benchmark run and the current direction of research.

Jan 1, 2008

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

By A Golev, G Corder

The concept of the circular economy has been gaining traction both in Europe and China.In Europe the Ellen Macarthur Foundation see their mission as accelerating the transition from a linear take-make-dispose economic model to a circular model that is restorative and regenerative by design, and aims to keep products, components and materials at their highest utility and value at all times. The Chinese Circular Economy initiative is effectively a sustainable consumption and production program utilising cleaner production, industrial ecology and life cycle management approaches to meet the national challenges of maintaining rapid economic growth while simultaneously enhancing environmental quality and maintaining social progress. A key characteristic of both of these circular economy initiatives is to design out, reuse or minimise the generation of waste.The mining sector, by definition, is represented by linear rather than circular activities, by supplying resources to society. However, being one of the world’s largest waste generators, the sector can adopt similar logic to that of the circular economy to improve its sustainability performance. Waste is a critical issue along the whole metals value chain, from mining waste to eventual end-of-life products, such as scrap steel from construction and demolition waste or the growing problem of electronic waste.CITATION:Corder, G and Golev, A, 2016. Can mining be part of the circular economy or is it squaring the circle?, in Proceedings Life-of-Mine 2016 Conference , pp 121–123 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By M Berner, N A. Sifferlinger, E Fimbinger

Today, the advance rate of underground roadway development by drill and blast operation is limited by the need to ventilate the toxic blast fumes after each cycle. In deep mines this usually is only possible during shift changes when the related mine sections are free of persons. This results in roadway development advance rates of 4 m per shift, or 12 m per day. For long roadways this is a limiting factor in mining development in deep mines. Companies like EPIROC, KOMATSU, ROBBINS and SANDVIK are making serious R&D efforts to disc-cutting mobile miners to overcome this bottleneck. However, today, the achieved advance rates are less than 12 m per day in hard rock. If we achieve full robotisation and/or teleoperation from a safe place for drill and blast operation of an underground roadway development section, we could eliminate this bottleneck. Poisonous blasting fumes do not affect robots and machines as long as these fumes do not create aggressive acids. If we can keep the blast fumes isolated in the roadway development section for the shift until the next ventilation opportunity (eg shift change or designated ventilation times), we can do the drill and blast cycle more often in a shift, which will significantly speed up the advance rate. This requires robotisation of all work steps in the section: surveying, drilling, charging of explosives, blasting, loading and transporting material, roof support, installation of infrastructure etc. Also, cache storage for the material is needed. Special care for the ventilation system to keep the blasting fumes under control in the section is necessary. The paper discusses the aspects needed to achieve this robotisation and the related technical and operational tasks.

Sep 1, 2024

By G Corder

The aim of the circular economy is to accelerate the transition from a conventional linear take-make-dispose economic model to a circular model. It is restorative and regenerative by design and aims to keep products, components and materials at their highest utility and value at all times. This extended abstract presents a brief overview of the circular economy, provides application of the circular economy in other industrial sectors including the downstream metals value chain and proposes how circular economy thinking could progress the development of complex orebodies.CITATION: Corder, G, 2018. Can the concept of the circular economy help unlock complex orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 8–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018