Search Documents

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

Case Study: Dragline Swing to Dump Automation By Peter Corke, CSIRO Manufacturing Technology/CRC for Mining Technology and Equipment (CMTE) Peter Corke presented a case study of a project to automate the dragline swing to dump operation. The project is funded by ACARP, BHP Coal, Pacific Coal and the CMTE and is being carried out on a dragline at Pacific Coal's Meandu mine near Brisbane. Corke began by highlighting that the minerals industry makes extensive use of large, mechanised machines. However, unlike other industries, mining has not adopted automation and most machines are controlled by human operators on board the machine itself. Choosing an automation target The dragline automation was chosen because: ò draglines are one of the biggest capital assets in a mine; ò performance between operators vary significantly, so improved capital utilisation is possible; ò the dragline is often the bottleneck in production; ò a large part of the operation cycle is spent swinging from dig to dump; and ò it is technically feasible. There has been a history of drag line automation projects, none with great success.

Jan 1, 1997

Cataclysmic or flood-like release of gas-charged brines, hydrocarbons and slurries accompanied widespread mineralisation of Upper Devonian environments. These are well represented in the Canning and Burdekin Basins of Western Australia and Queensland respectively.The Burdekin Basin provides particularly instructive vein structural sequences. These fall into organic residue to carbonate paragenetic sequences which are known elsewhere to record progressive decarboxylation. Fibrous veins indicate overpressure in fractures with organic residues, acids and gas derivatives driven to overlying groundwater flows. This combination of large flow rates and potent organic mineralisers led to extensive arsenical rare-metal mineralisation which is similar to that concentrated in Upper Devonian extinction horizons of the Canning Basin. Organic-residue mineralisation appears concentrated by certain hvdrostructures and targeted upon particular species. These controls need to be understood to guide modern management stragegies for mineralised organic and nitrogenous wastes.

Jan 1, 1990

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

By W Lu, D Wang

Study of coal oxidation at low temperatures forms the basis of investigating the inherent properties of spontaneous combustion of coal. In general, the process of coal oxidation at low temperatures is very complex, involving many factors. Experiments examining the properties of oxidation and ignition of coal have been carried out. Based upon the results of these experiments, the catastrophe properties in the process of coal oxidation are analysed and the mechanism of catastrophe is proved for the ignition of coal. A folding catastrophe model is also established for the process of coal oxidation. Results obtained show that the process of coal oxidation to ignition is discontinuous, where the coal-environment system yields structure destabilisation. The system can jump from one stable attractor to another. The research results presented in this paper help to show the irregularities of coal oxidation at low temperatures and how to pursue effective control measures.

Jan 1, 2005

By H He, S Tillotson, S Gibbons, J Shaw

"Water evaluation and management during mining exploration and operational activities is crucial to minimise direct and indirect operational costs and also in delivering mining companies the less tangible, but equally critical æsocial license to operateÆ.Mining is often carried out in remote areas, where the mine will be the most significant and visible user and potential contaminator of water resources. However, wherever it is located, a mineÆs use of water must be managed in the context of two key aspects: the natural parameters of the resource; its abundance, its temporal variability and its chemical and physical qualities other users of the resource; other industry, potable water supplies and ecological requirements of local habitats.It is vital, therefore, that this commodity be assessed to an appropriate degree to help establish the viability and sustainability of the mining project and identify those other stakeholders who may be affected by the mining companyÆs activities.This paper outlines the background to catchment-scale model and presents a cost-effective method for establishing a robust water baseline and creating a water management tool to be used throughout whole mine life cycle. Numerical surface and groundwater modelling has long been established as a tool for reactive management, following collation of yearsÆ worth of data. Now, using freely available remote sensing data and desk study information, analytical modelling techniques can be used cost effectively to provide mining companies with a tool for assessing and managing their water consumption requirements at the outset of a new project venture.The paper includes a selection of case studies to show how the use of analytical modelling can be used as an evaluation and management tool to help not only assess general watershed parameters and water availability but also how it can be used as a tool to provide decision makers with the information to complete æwhat if?Æ scenario assessments. The case studies illustrate how a combined hydrological and hydrogeological model may enable identification of sensitive receptors, water competition issues and contaminant migration pathways to help manage the risks associated with water consumption and its potential contamination from exploration and operational activities.CITATION:Gibbons, S, Shaw, J, Tillotson, S and He, H, 2013. Catchment-scale water modelling and its role in risk management during mining exploration, in Proceedings Water in Mining 2013, pp 175-188 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By P C. J Blackney, I M. Glacken

Spotted Quoll is a massive sulfide nickel deposit located in the Forrestania greenstone belt in the Archaean Yilgarn block in Western Australia. Discovered in October 2007, mining has progressed from open pit to underground and currently uses longhole open stoping with paste fill as the primary stoping method. Immediately prior to 2019, the Mineral Resource estimate (MRE) was defined by a single grade domain of nickel greater than or equal to 0.8 per cent, irrespective of the host lithology, a legacy of the original ore wireframe being built using explicit methods. While a number of obvious structural offsets were honoured in this nickel grade domain, only one modelled fault was used to undertake domaining of arsenic. From 2019 onwards, implicit modelling in Leapfrog Geo™ was used to construct a mine-scale geological model, which triggered the definition of a high-grade core of massive/matrix nickel sulfides surrounded by a low-grade halo of stringer/disseminated nickel sulfides in the surrounding rock. As part of the evolution of the geological model and with the aid of Seequent Central™ to allow collaboration between site-based mine geologists, Perth-based resource geologists and Melbourne-based consultants, a detailed review of the structural mapping was carried out as additional information from underground development became available. This allowed numerous faults and shears to be identified – particularly in the lower half of the mine. These were used to define further structural domains and to refine the understanding of the nickel and arsenic grade distributions in the mineralised envelope. The increased definition to the domains provided by the geological model resulted in a significant improvement in the accuracy of the Mineral Resource estimate, as measured by reconciliation using voids of the mined stopes determined from the cavity monitoring survey (CMS).

Mar 22, 2022

A new engine family has been developed by Caterpillar Tractor Co. for application in off-highway trucks. This family, the 3500 Series is available in three configurations, covering a 600-1200 kilowatt range. This engine series incorporates the latest in design technology, stringent functional specifications for servicing ease, fuel economy, reliability, optimum performance and parts interchangeability. TECHNICAL INTRODUCTION The 3500 Series Engine has been under development by Caterpillar for over eight years and has undergone extensive testing in the laboratory and in field prototype units. - The engine configuration is a 600 Vee in 8, 12, and 16 cylinder versions. - The intermittent power output per cylinder is 75 kilowatt (100 HP). Net power for off-highway trucks is 600-1200 kilowatt (800-1600 Hp) depending on engine configurations. The 3512 (3500 Series Engine 12 cylinder Vee configuration) was the first model of the 3500 Series released. These engines offer optimum user value in terms of product durability, reliability, fuel consumption, performance and installation flexibility. Additional features of 3500

Jan 1, 1982

By Ault A. R

The recent modernisation program at the Risdon electrolytic zinc smelter of Pasminco Metals - EZ (PMEZ) inyolved significant changes to the composition of cell electrolytes. The most significant were increased acidity and sulphate level, a reduction in Co level, and the replacement of 2-naphthol in the additive mixture with licorice. In determining acceptable operating ranges, a relatively large number of industrial deposition tests under controlled conditions was required. The cathode zinc deposits so produced were examined in terms of overall appearance, crystal structure according to X-ray diffraction, and a micro-roughness parameter. Beginning with typical deposits produced in the presence of an excess of one of the addition agents glue or antimony or a mist suppressant (licorice or 2-naphthol), a simple classification system was developed. In this system, the deposits are divided into the following types: Doughy, Pinholed, Compact and Stressed. There was a weak correlation between deposit type and crystal orientation. In terms of ease of stripping, observations in plant operations showed that only Compact and Pinholed were consistently acceptable. Current efficiency was normally maximised by producing a Compact deposit. Process variables such as zinc concentration, temperature and the use of strontium carbonate were found to cause changes in deposit type if the reagent mixture used was unchanged. From the knowledge gained, guidelines were developed to allow glue and antimony additions to be altered to fit new circumstances. The simple classification system was first used to expedite recovery from undesirable morphologies and then to optimise individual cell units operated under substantially different conditions. It is believed that finer control could be exercised by determining the micro-roughness of Compact deposits. However, difficulties can arise if sudden, large deviations occur and go undetected. Suggestions are given for an improved additive control system. The classification system developed has been compared with published information in the literature, and good correspondence was noted suggesting a predictable relationship between short-term, laboratory deposition tests and observable phenomena in industrial electrowinning cells run under steady conditions.

Jan 1, 1993

By R Graber, R Johnson

North American steelmaking practices have evolved based on access to iron ore raw materials containing very low phosphorus contents, typically less than 0.025 per cent P. Cleveland-Cliffs managed Tilden iron ore operation produces iron ore pellets exceeding 0.030 per cent P, which by global standards would be considered low phosphorus, but has limited penetration in the North American iron ore market due to phosphorus content. Recently cathodoluminescence microscopy has augmented more standard ore characterisation techniques enhancing our understanding of the genetic history and process mineralogy of TildenÆs complex martite ore. This paper highlights the unique capabilities that cathodoluminescence microscopy provides for phosphorus mineral identification in fine-grained iron ores.

Jan 1, 2005

By E ¦iftti, A Koenig

Natural sphalerite associated with copper, silver, lead-zinc, tin and tungsten deposits from various world-famous mineral deposits have been studied by cathodoluminescence (CL), laser ablasion inductively coupled plasma mass spectrometry (LA-ICP-MS), electron probe microanalysis (EPMA) and electron paramagnetic resonance (EPR) to determine the relationship between trace element type and content and the CL properties of sphalerite. In general, sphalerite produces a spectrum of CL colour under electron bombardment that includes deep blue, turquoise, lime green, yellow-orange, orange-red and dull dark red depending on the type and concentration of trace quantities of activator ions. Sphalerite from most deposits shows a bright yellow-orange CL colour with lmax centred at 585 nm due to Mn2+ ion, and the intensity of CL is strongly dependent primarily on Fe2+ concentration. The blue emission band with lmax centred at 470 - 490 nm correlates with Ga and Ag at the Tsumeb, Horn Silver, Balmat and Kankoy mines. Colloform sphalerite from older well-known European lead-zinc deposits and late Cretaceous Kuroko-type VMS deposits of Turkey shows intense yellowish CL colour and their CL spectra are characterised by extremely broad emission bands ranging from 450 to 750 nm. These samples are characterised by low Mn (<10 ppm) and Ag (<1 ppm), and they are enriched in Tl (1 - 30 ppm) and Pb (80 - 1500 ppm). Strong green CL is produced by sphalerite from the Balmat-Edwards district. Amber, lime-green and red-orange sphalerite produced weak orange-red CL at room temperatures, with several emission bands centred at 490, 580, 630, 680, 745, with lmax at 630 nm being the strongest. These emission bands are well correlated with trace quantities of Sn, In, Cu and Mn activators. Sphalerite from the famous Ogdensburg and Franklin mines exhibited brilliant deep blue and orange CL colours and the blue CL may be related to Se. Cathodoluminescence behaviour of sphalerite serves to characterise ore types and help detect technologically important trace elements.

Jan 1, 2008

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978

Caving is the lowest cost underground mining method, provided that drawpoint spacing, drawpoint size and ore handling facilities are designed to suit the caved material and that the drawpoint horizon can be maintained for the draw life. In the near future several open pit mines that produce in excess of 50 000 tons per day will have to examine the feasibility of converting to low cost, large scale underground operations. Several other large scale, low grade underground operations will experience major changes in their mining environments as large dropdowns are implemented. These changes demand a more realistic approach to mine planning than has occurred in the past, where existing operations have been projected to increased depths with little consideration of the change in mining environment that will occur. As economics force the consideration of underground mining of large, competent orebodies by low cost methods, the role of cave mining will have to be defined. In the past caving has generally been considered for rock masses that cave and fragment readily. The ability to define cavability and fragmentation, the availability of large, robust LHDs, a better understanding of draw control requirements, improved drilling equipment for secondary blasting and reliable cost data have shown that competent orebodies with coarse fragmentation can be exploited by cave mining at a much lower cost than with drill and blast Methods.

Jan 1, 1995

By A Croll

A panel cave using LHDs for ore extraction came into production at Premier in 1990 at a depth of 630 metres below surface on the western side of the mine in the BA5 mining block. A post-undercut mining sequence was used with all development on both the undercut and production levels completed prior to the undercut being advanced over the pre-developed drawbells. Support and rock mass damage on the production level was extensive as the undercut moved overhead. Undercutting and coarse fragmentation created problems. The mining sequence was changed to an advance undercut with the minimum of development and support undertaken on the production level prior to the undercut moving overhead. Only once the abutment stresses had stabilised were drawbells developed and final support installed. The height of the undercut drill design was decreased from 18 to 13 metres. The changes resulted in markedly less rock mass and support damage on the production level. Lessons learned in the BA5 mining block on the 630 level were incorporated into planning and scheduling the BB1E mining block which came into production on the 732 metre level on the eastern side of the mine in 1996. An advance undercut mining sequence was planned, undercut height was minimised and undercutting parameters were optimised in terms of the BA5 experience. Numerous problems still occurred. As the undercut area increased in size severe spalling from the cave back resulted in vertical propagation of the cave to a height of 30 metres instead of the planned 13 metres. The resultant coarse fragmentation created secondary blasting problems and an excess of undercut ore that had to be loaded and trammed, slowed the rate of undercut advance. The planned mining sequence was compromised and considerable support and rock mass damage resulted on the production level below. Once these problems had been overcome the undercut advanced at the planned rate and continuous caving initiated at the predicted hydraulic radius. At a later stage the unexpected ingress of water hampered undercut drilling and slowed the rate of undercut advance in a section of the cave. Leads and lags between adjacent tunnels and the overall face shape could not be developed as planned. The rate of natural horizontal cave propagation exceeded the rate of undercut advance and three undercut drilling tunnels were extensively damaged. More tunnel development on the production level prior to undercutting than was planned resulted. The slow advance of the undercut and high abutment stresses caused extensive damage to installed support and the rock mass on the production level, 15 metres below. Experience in the BB1E mining block on the 732 metre level has taught that an advance undercut mining sequence reduces damage on the production level markedly. Extremely tight control on the rate of undercut advance, leads and lags between adjacent tunnels and overall undercut face shape as well as extraction ratio, tunnel development and support sequence on the production level below is required. Premier Mine plans to implement a block cave at a depth in excess of 1000 metres within the next decade. All the experience gained on current mining levels together with data collection and numerical modeling is being used to plan the proposed mining operation. The geotechnical challenge of mining at this depth in weak rock has been identified as the greatest risk to the project. Challenges centre around adopting the correct mining sequence, limiting the extent of rock mass damage associated with undercutting and effective support. The hydraulic radius needed to initiate caving, fragmentation, drawpoint spacing, secondary blasting and the possibility of seismicity are geotechnical concerns that are being addressed. Results to-date suggest that a pre-undercut mining sequence with all development and support on the production level carried out only after the undercut abutment stresses have passed overhead will have to be implemented.

Jan 1, 2000

By E Ah Mu and C R Lilley, A D. Campbell

Cave propagation is a complex process due to interacting variables such as mine geometry, rock mass heterogeneity and complex structural networks and stress fields. The Ernest Henry sublevel cave (SLC) is directly below an open pit, which provided an opportunity to observe and measure rock mass failure as the cave initiated and propagated through the pit wall. This paper describes interaction between the open pit and SLC as well as rock mass failure mechanisms observed from the start of the SLC to surface breakthrough.Cave propagation and slope failure mechanisms were found to be governed by intermediate structures, while the cave shape was largely controlled by cave-scale faults. The open pit, production-level geometry and production draw strategy were also important factors for cave and subsidence growth. Cave propagation was episodic and asymmetric in shape due to the orientation and relative position of geological structures, combined with the effects of the increasing SLC geometry and drawdown from the underlying production levels. The precursors and failure mechanism of a 2.5 Mt wall collapse are also reviewed in detail.Cave growth was simulated using a 3D, non-linear, discontinuum finite element model coupled with Newtonian Cellular Automata. Model results are compared to field observations and monitoring data to determine the accuracy of forecasts and compared models versus actual rock mass response during cave propagation.CITATION:Campbell, A D, Ah Mu, E and Lilley, C R, 2016. Cave propagation and open pit interaction at the Ernest Henry Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S R. Hencher

The development and availability of modern software for cavern design over recent years has provided design engineers with a range of usable design tools. The paper discusses the range of modern software available, presents a design methodology, reviews ground investigation requirements and software available for data processing and management, and discusses requirements and common analytical considerations with reference to typical packages. Caution is given of the tendency for readily available and user friendly software to be used without a full appreciation of the underlying engineering principles.

Jan 1, 1999

By T R. Gibbons, I Grayand

Geotechnically massive strata may lead to a host of problems during longwall mining. These include windblast on initial goaf fall, sudden loadings on powered supports, periodic weightings, fractures that may propagate to surface, and extreme subsidence problems. It is essential to identify these problems prior to mining and to appropriately deal with them. The problem is essentially that the rock mass does not breakup evenly and when it does so it tends to produce large blocks which may suddenly move. The rock types that produce these problems tend to be massive sandstones, massive siltstones and sometimes igneous sills. The fundamental problem with these is that they do not breakup readily. This is because the ratio of stress they are subject to compared to their strength is low. Thus, the shallower mines with lower stresses are more subject to this problem than deep highly stressed ones with similar strength rock.

Nov 29, 2022