Search Documents

By J E. Moffatt, N A. Spooner, T J. de Prinse, D J. Ottaway, E Klantsataya, L d. S Teixeira, B W. Smith, T B. Payten, G Tsiminis

Single wavelength fluorescence sensing has been used in the preconcentration of ores for many years in situations where it is typically specific to the mineral of interest. Examples of fluorescence sensing include the sorting of diamonds in diamond mines and the sorting of scheelite in tungsten ores. However, the number of minerals that show useful single wavelength fluorescence properties in the visible spectrum is relatively small, so the application of fluorescence sensing is currently limited to niche application in the minerals industry. Recent developments at the University of Adelaide have focussed upon extending fluorescence signal measurements into the infrared spectrum, as well as investigating multi-wavelength fluorescence known as up-conversion fluorescence. These techniques may not only significantly increase the number of minerals that exhibit fluorescence properties suitable for both identification and sensor-based sorting, but also provide mineral-specific signatures of higher quality than previously attainable. This paper details the research work carried out by the University of Adelaide and funded by CRC ORE to develop a mineral-specific fluorescence sensor. The sensor targets two fluorine bearing minerals, fluorite and fluorapatite, that are common in many base metal ores such as porphyry copper ores and silver/lead/zinc ores. Fluorine is a known penalty element in mineral products derived from these ores, so mining companies need to monitor and control the amount of fluorine in their final product to keep it below commercially agreed specifications. Currently there is no real time sensor capable of monitoring fluorine in the ore feed so monitoring and control is carried out using time-consuming standard sampling and off-line laboratory measurements. The development and application of a real time fluorine sensor will enable the mining companies to monitor and control fluorine levels in the plant, greatly reducing the time and cost associated with producing their mineral concentrates within the prescribed specifications.

Nov 10, 2020

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By R A. Pax, B Cornish

Increasing the throughput of the MMG Century operation by over 25% from past practice to preserve cash flow close to the end of life of mine has revealed new throughput and load dynamic instabilities in the SAG mill causing significant time averaged loss of production. A twelve microphone array around the SAG mill (Pax, 2014) using the non-contact acoustic measurement methodology (Pax, 2011, 2012) has been used to diagnose the new dynamics. Dynamic acoustic noise signal information allows discrimination of the behaviour of the steel balls and the rock. Determination of mill load, toe and shoulder angles, water holdup, and proxies for mill load are possible.The instability was diagnosed with the help of an abnormality in the liners/lifters of the SAG mill with one row of lifters having a slightly increased in-mill life compared to the rest. The steel shoulder angle is observed to be disturbed cyclically at a rate of precisely one revolution at low throughputs of 750 t/h. However, at throughputs closer to 1100 t/h, the cyclic signal disappears indicating additional dynamics to randomise the repetitive behaviour of the mill charge. The cyclic signal has been used to operate the SAG mill with improved stability at 1100 t/h by adjusting the feed water addition rate.This paper presents and discusses these results and proposes the suggested origin of the extra dynamics. A small consistent aberration of the lifters circumferentially provides a useful detector of stable mill operation and a novel sensor for the dynamics of the internal operation of a SAG mill.CITATION:Pax, R A and Cornish, B, 2015. A novel measurement for the internal operation of a semi-autogenous mill using acoustic sensors – a case study, in Proceedings MetPlant 2015, pp 120–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

By Waddell S

A new procedure has been developed for the direct determination of metals loaded on activated carbon. It involves preparation of a suspension of the powdered carbon in water, followed by direct sampling of the suspension with a micropipette,and analyses by atomic absorption spectroscopy using carbon rod atomization. Advantages of the method include the simplicity of sample preparation and the ability to provide a complete metal analysis in 1 - 2 hours. This enables carbon-in-pulp operators to respond quickly to changes in plant efficiency arising from carbon fouling. The successful application of the method has been demonstrated for gold, copper, nickel and iron. Other elements to be surveyed include calcium, magnesium and silicon.

Jan 1, 1984

By B Muller

The disposal of tailings has become a greater issue due to the changing economics of mineral extraction. The processing of lower grade deposits and tougher environmental regulations has led to the selection process for tailings disposal options becoming more complicated. Current selection methods are too time consuming or too easily manipulated for inexperienced users to use successfully. This paper examines a different method for the initial selection of a tailings disposal system, using a numerical system that was introduced into the mining method selection field. The numerical method system was compiled by reviewing previous work done on the positive and negative aspects of the tailings disposal methods used by the coal and metallurgical mining industries. Assessing the common trends and design aspects of each of the methods was undertaken and a ranking was designed to explain how well suited the tailings disposal methods are to a situation. The tool successfully analysed sites using common data to indicate methods for disposal that would have provided minimal technical problems, low environmental risk and been practically possible. The tool also proved successful in identifying critical areas that would need further investigation. This new system was tested on some disaster case studies from around the world in order to show that it could have successfully selected a different method for tailings disposal that would have prevented the disaster.

Sep 26, 2011

By P Lindsay

A numerical model has been developed to simulate the effectiveness and costs of a number of conceptual remedial measures aimed at reducing acidity and metal concentrations in the Ngakawau River and its tributaries near the Stockton Coal Mine, situated on the West Coast of New Zealand. The Stockton Coal Mine has been in operation over the past 100 years. During that time, seepage from waste rock dumps has contributed to elevated acidity and metal concentrations in the Ngakawau River and some of its tributaries. The yearly mean rainfall at the mine site is 6000 mm. The model, developed using GoldSim software, simulates rainfall, run-off and stream discharge for 26 tributaries. It then calculates acidity and metal concentrations in the mine impacted tributaries and the dilution downstream from the mine. The model has been calibrated to measured flow and acidity and metal concentrations in the Ngakawau River and some of its tributaries. Acidity and metal loads are removed from the system in accordance with specified efficiencies and capacities of the respective conceptual remedial measures. The user can compare specific remedial measures, or a combination of conceptual remedial measures. The model predicts the acidity and metal concentrations at a number of monitoring stations for any remedial strategy selected by the user. It also calculates the capital and operational costs for that particular remedial strategy. This paper presents the development of the numerical model and describes how the end-user can use it to compare the efficiency and costs of various remedial strategies by running different æwhat ifÆ scenarios.

Jan 1, 2006

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By A He, J Li, J Pan, J Clout

The removal of sulfur from SO2 containing flue gas is improved by adsorbing SO2 into solution with manganese ions as catalyser, however, burnt lime slurry has to be added to modify solution pH and the CaSO3 by-product is of low economic value. In this paper a novel one step process for simultaneous manganese leaching-desulfurisation of flue gas is presented. An investigation of the effect of process parameters included flow rate and SO2 concentration in flue gas, adsorbing time, solution to solid mass ratio, leaching time, and their impact on the oxidation and removal of SO2 from flue gas. The catalysing mechanism of manganese ions on the oxidation and SO2 removal was demonstrated by calculation of the species originating from manganese ions and SO2 in the solution according to solution chemistry. SO2 removal in the adsorbing solution took place at pH 5 - 6, where manganese ions dominantly occurred as Mn2+, and the chain reactions for oxidation of SO2 starting from HSO3- were improved by the presence of Mn2+. SO2 bearing flue gas was effectively desulfurised by leaching rhodochrosite (MnCO3), with desulfurisation of the flue gas and modifying the solution pH being achieved simultaneously, and MnSO4 of high economic value recovered from the leachate. 85 per cent manganese leaching and over 70 per cent desulfurisation of the SO2-bearing flue gas were achieved with only one adsorption stage under optimum conditions.

Jan 1, 2004

By Johnson M, Gaudin A

With the advent of Computer aided mapping and surface modelling techniques Geologists and Engineers have had to become familiar with the capabilities and limitations of these systems to effectively use them. In this paper we will trace a short history of the rather rapid progress in this area. From this historical perspective we will make some observations and use these to guess at what the future holds. We hope that this paper will assist in clarifying the develop- ments in computer assisted mapping and modelling and promote thought on how these techniques may be best applied to the problems of the Mineral Industry.

Jan 1, 1983

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By Pandey A. K, Srivastava A, Das A

Drilling and blasting constitute important activity in mining operations and account for around 20% of the total excavation cost. The utilization coefficient of energy for explosions of the fragmentation type is hardly 15 to 2035 and an enhancement in this is possible only through optimization of blast design. Designing a 'blast is a complex planning task, which for optimum results calls for matching the energy level of the explosive, rock properties and bench geometry. Optimum blast design needs a comprehensive study and an objective analysis of the intersecting elements. A cost optimised approach is often adopted with due consideration for all the cost sectors viz., drilling, blasting, loading, hauling dumping, and primary crushing, contributing to the overall miring cost. The present study deals with a performance prediction model which predicts the optimum burden for an explosive system in a given rock type to produce a certain desired fragment size. The model is framed on the inputs : shovel size, drill size, unit cost of drilling, bench dimensions, rock density, bond index, unit cost of explosive, maximum work potential. The model has been extended to compute the drilling and blasting costs for an assumed size of the bench to be blasted per round, so as to arrive at the overall cost optimization from a number of explosive systems. A comparative cost calculation with different explosive systems has been presented for a typical iron ore mine in India.

Jan 1, 1990

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G B. Arehart, J L. Mauk

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulphide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3ë in d18Oquartz between maximum and minimum isotopic values for the deposit. Significant overlap in d18Oquartz values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

By Mauk JL, Arehart GB

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulfide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3%o in 618Oq,,,,,= between maximum and minimum isotopic values for the deposit. Significant overlap in 618Oqu,, values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

By Teague JK, Read HW

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years. Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the Illawarra Measures of the Southern Coalfield of New South Wales were carried out. The optimum range of vitrinite was found to lie between 45% and 60% (mineral matter free). Above and below this vitrinite range coke strength deteriorated. I Coke strength indices increased with rank and the optimum vitrinite content increased with an increase in rank. These changes will require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal. . T Use of- petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved. Significantly more work is required before coal reserves can be utilised to optimum advantage. This work would require extension of-the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1970

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011