Search Documents

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By D J. Black

The process of longwall coal extraction coal causes fractures in the overlying and underlying strata and these fractures become pathways for gas released from adjacent coal seams to flow into the mine workings and contaminate the ventilation air. If the rate of gas emission exceeds the diluting capacity of the ventilation air, the gas concentration will increase and exceed the statutory limit resulting in production delays.All potential gas sources within the planned mining area, including coal seams located above and below the working seam, should be identified and sufficient gas data collected and used to determine the specific gas emission from each gas source. Gas reservoir and emission modelling is recommended to determine specific gas emission and changes in gas emission from individual sources over the planned mining area. Accurate gas reservoir and emission modelling provides the information required to accurately design gas drainage programs to effectively manage gas emissions and minimise the risk of ‘gas-outs’.Given the increasing occurrence of incidents of gas concentration in ventilation air exceeding the 2.0 per cent statutory limit and changes to mine plans to avoid ‘difficult-to-drain’ areas, it is apparent that many operations are not effectively utilising gas reservoir and emission modelling to identify high gas emission areas and are not completing sufficient gas drainage in advance of planned mining.The process of gas reservoir and emission modelling to support gas drainage design to control tailgate gas concentration and fugitive emissions is presented and discussed.CITATION:Black, D J, 2017. Gas reservoir and emission modelling to evaluate gas drainage to control tailgate gas concentration and fugitive emissions, in Proceedings Australian Mine Vent Conference 2017, pp 65–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

APPIN AND TOWER METHANE ENERGY PROJECTA world first in energy innovationBHP has teamed with Energy Developments Limited and Lend Lease Infrastructure, to establish an electrical power generation facility that utilizes methane produced as a by-product of mining at BHP's Appin and Tower coal mines in southern New South Wales.

Jan 1, 1998

Gas well tests were performed on 17 wells in the Roma area. The procedure used in the test programme incorporates an initial isochronal test followed by what is described as the "two flow drawdown" technique. The second flow of the two flow drawdown test was conducted for sufficient time to allow transient investigation of the surrounding reservoir. This combination of tests allows the evaluation of stabilized production capacity in addition to the determination ,of several important reservoir characteristics.It also provides a qualitative indication of reserves, by reflecting the presence or absence of reservoir boundaries within the drainage area affected during the test.

Jan 1, 1968

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

By Y Zhang, X Yi, J Deng, J Zhao, J Song

To obtain the combustion process of a coal fire, a high-temperature programmed system is used to simulate the spontaneous combustion process of fresh and weathered coals. Both fresh coal and weathered coals from Liulingou, Inner Mongolia, China, were used to examine the gas releases from constant temperature to 650°C. Moreover, gas release rate was used to calculate the characteristic temperatures. The results showed the coal samples lasted to oxidise under high temperatures, and released plenty of heat to assist self-heating. The humic acid contained inside the weathered coal went through thermal decomposition as temperature rising and generated gases. This resulted in increasing concentrations of CO, CO2, CH4, C2H4, and C2H6. Changes of CH4, C2H4, and C2H6 gases were also similar. For weathered coal, concentrations of three gases were kept in balance under low temperatures, increased rapidly with the temperature rising. After the ignition temperature, the concentration of hydrocarbon was reduced. In addition, particle size affected coal spontaneous combustion. Coal samples with less than 0.9 mm in size produced much more CO than others. This study has examined coal spontaneous combustion caused by coal weathering during mining and its impacts on self-heating and pyrolysis in the process.CITATION:Deng, J, Song, J, Zhao, J, Zhang, Y, Yi, X and Zhang, Y, 2017. Gaseous products of weathered coal during the process of spontaneous combustion, in Proceedings Australian Mine Vent Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M Hino, Y Sasaki

Sustainable handling of municipal waste and sewage sludge has an important goal to recycle resources without supply of harmful substances to humans or the environment. The gasification mechanism of phosphorus from municipal waste and sewage sludge during the incineration process has been investigated to develop a phosphorus recovery system. Quadrupole mass spectrometer coupled to an electric furnace is applied to study the vaporisation behaviour of phosphorous gas phases from municipal solid waste (MSW) incinerator ash of sludge during solid-state reduction by carbon. Measurements are carried out in vacuum conditions of 2 x 10-6 Torrs and furnace temperature range 573 - 1773 K, at a heating rate of 7.22 K/minute. It has been found that most of the phosphorus is vaporised as PO2, P2 and P4, in agreement with thermodynamic estimation despite a shift in the temperature regimes.

Jan 1, 2006

Elastomeric compression gaskets for segmental tunnel liners are capable of fulfilling all sealing requirements for one pass constructed tunnels.Once the segments are mounted and the gaskets are compressed the watertightness of the tunnel is guaranteed at once and for the whole technical life time.The only prerequisite for effective sealing is that tolerances in the tunnel segments be kept within reasonable limits.

Jan 1, 1993

Longwall mining in Australia is approaching maturity. Longwall production from 'state of the art' Australian longwall mines now rivals similar US based longwall operations. Regrettably however, Australian gate road development rates in general fall short of the required development to longwall production ratios that are required to sustain annual longwall production capabilities. By contrast, most US based longwall mines achieve the required development to longwall production ratios to sustain their longwalls. This is despite many having to drive three heading longwall panel gate headings to meet regulatory requirements.

Jan 1, 1998

By Downs M

The use of a cutting machine designed to allow simultaneous cutting and setting of roof supports has numerous advantages few development roads in coalmines. The use of such a machine with the added ability to cut a curved roof profile is of considerable interest for longwall development in thick coal.

Jan 1, 1998

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007

By Burnett C. C H

GEMNet, (Grade Estimation using Mapping Networks), is a grade/reserve estimation software system that uses the artificial intelligence technique known as neural networks to perform reserve estimates from both two- and three-dimensional data samples from a mineral deposit. The system is the result of research carried out over the past three years into the feasibility of using neural networks for reserve estimation at the AIMS Research Unit in the Department of Mineral Resources Engineering at the University of Nottingham. This paper describes the architecture of the GEMNet system including details of the neural network components of the system. The performance of the GEMNet system is then compared to several other widely used reserve estimation techniques on two reserve estimation examples. The results produced by the GEMNet system compare favourably with more conventional estimation techniques, but require fewer assumptions to be made about the form of the data used, and do not require the use of complex mathematical modelling.

Jan 1, 1995

By S R. Pecover

AustraliaÆs opal and sapphire mining industry has fallen from its peak in the 1980s and 1990s into a significant low today. This is not due to exhaustion of the resource, but instead an over-reliance of the Australian miner on achieving a fair price for the gemstone product from offshore middlemen dealers. Gemstone and geological research is also at a low as Federal higher education expenditure has fallen with research institutions relying increasingly on private funding in an environment of restricted autonomy and flexibility for researchers. What little remaining research skills the universities have is being bled into the private sector as a result of the mining boom and encouraged by lower than average academic salaries. Nevertheless, some highly innovative research has been taking place, often by self-funded individuals and retired academics simply with a desire to advance the understanding of the particular branch of science in which they are interested. New models for the formation of sapphire and opal are now beginning to be applied to the exploration for these gemstone commodities. This research, together with well thought out plans for managing the gemstone product through its value-adding steps to the jewellery retail level, has the potential to bring about a resurgence in the Australian gemstone industry.

Jan 1, 2008

The elements of consistent structural de sign models for underground structures are explained. Such models should comprise at least ground properties, excavation and support methods, computational models for analysis, failure hypotheses, and in-situ monitoring. The fundamental characteristics of the interaction between ground and support are investigated. Then, plane strain models for soft ground tun- nelling and design models for rock tunnelling employing stress release at the tunnel face are elaborated. Some numerical evaluations are gi- ven in diagrams, comparing approaches of dif- ferent authors. Comments are presented on nume- rical three-dimensional models (visualized by structural models for mining in rock salt), on the interaction of in-situ monitoring and design, on structural safety for underground structures, and finally on the general develop- ment of structural design models in geo- Techniques.

Jan 1, 1987

This paper outlines the manner in which legislative control for tunnelling and allied operations has evolved, detailing Victorian experience. It examines the concept of mine managers as it relates to the industry and attemps to illustrate its benefits. The Victorian experience in relation to fatal and serious accidents is examined in detail, particularly in the allied art of trenching and examines the Krings system of trench lining support which is hoped will catalyse an increase of engineering expertise in this area. The paper concludes by demonstrating that safety awareness is not incompatible with production efficiency or economic viability.

Jan 1, 1981

The current talk of risk management as a separate discipline and management function is like earlier imposition of Quality Control (QC) as an overlay on shoddy production management. Risk management is vital, but is integral in the way we marshal our staff, make decisions, then monitor and review and make crucial secondary decisions. New leaders must not assume that hiring experts ensures good decisions. It is only the essential step one. The worst company I worked for had more expertise than the best. The difference was in culture and decision-making processes. Failed feasibility studies, persistent technical factions in a company that cancel each other, heaps of expert consultant reports piled up like a dump of bricks, even great but half-managers in large and small companies cancelling expertise at their disposal, are the worst manifestations. Just daily foul-ups are common even amongst smart people. We miners have made a great industry but are content to drift far below excellence, even where that word is bandied around. All the management literature and management courses will not right the situation û we have been sending budding managers to this good stuff for two generations and the effects are worthwhile but marginal. A few key ideals, ideas and slogans are not the way. These make inspiring books that work about as long as the Christmas spirit does in the real world. What we need is a coachesÆ manual and a standard of the essential package of culture and work processes that make excellence possible and show how to maintain it long term. It has not been written until now because most managers want to remain dilettante amateur managers without the discipline that creates excellence. First, believe excellence is possible and worth any effort; then commit to it.

Jan 1, 2007

The Income Tax Assessment Act ["the Act"] levies tax on a taxpayer's taxable income. At a time when commerce and life were more simple, the calculation of taxable income had some connection with logic and a taxpayer's capacity to pay. However, as a result of successive governments' different views of equity, their perception of avoidance, their needs for revenue and their changing views on capacity to pay, the rules determining the calculation of taxable income have continually changed to the point that logic is no longer relevant. Taxable income now is simply the product of the application of a complex set of rules.

Jan 1, 1990

In the past two and a half years, over 40 000 metalliferous mining and related services personnel have been trained through an Australian Generic Safety Induction system. This is almost half of AustraliaÆs metalliferous mining related workforce. This remarkable industry acceptance and delivery of safety courses is supported by Acacia Resources, Great Central Mines, Homestake, Newcrest Mining and WMC Resources, amongst hundreds of other mining, exploration and major contracting and services companies. MARCSTA; the Mining and Resources Contractors Safety Training Association (a pro-active not-for-profit self-help group of 24 major contracting companies) developed this generic safety induction. MARCSTA set out to find the æcommon groundÆ necessary to help address the evident safety problems and cost of re-training that were plaguing development of an internationally competitive and productive export industry. The incredible expansion of Australian mining during the decade fuelled a need for out-sourcing, resulting in much larger numbers of contractors on-site. At the same time, changes within Australian legislation, community expectations and the development of huge fly-in/fly-out operations and widespread skills shortages led to a rapid labour turnover and a higher paid workforce. Many Australian mining houses also ran international operations, particularly in South East Asia and head hunted people across the world. The skill levels fluctuated and fell at some local operations. Employers could no longer rely on systematic in-house training of permanent employees to improve safety and productivity as workers could and often did move on. Serious discrepancies in both quality and quantity of safety induction training and work practices occurred. Repetitive, boring and ineffective safety training became an embarrassing and costly burden for companies and workers alike. Then a spate of mining deaths sparked highly publicity, workforce concern and a demand for improvement from government, unions and corporate stakeholders. MARCSTA recognised it had to develop a high-quality safety-training program to satisfy the needs of all employers and be acceptable to others within the industry. This induction system had to be flexible enough to meet differences in legislation between states and industry sectors and be portable to enable cost and time savings for the new transient workforce. Changes in the last two years as a result of evaluating and incorporating various Taskforce inquiries into underground mining fatalities later led to the development of the MARCSTA Underground Safety Induction. This logical development added to the run away success of MARCSTAÆs General Safety Induction and was seen to be essential for many surface mines that were planning to develop underground operations. There are many lessons that MARCSTA learnt during its development that Pacific and South East Asian mining operations can benefit from. The most important of these are the support of stakeholders within industry and the recognition of higher safety and health expectations from workers and government. This goes hand-in-hand with the productivity and return on investment expectations of companies and their shareholders.

Jan 1, 1999