Search Documents

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

By Junpeng L, Huiguo Q

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

By Zhansen P

This paper describes the test re- sults which give a complete proccess of failure of concrete lining embedded in sand medium under load, including the order of appearance of crack along the lining up to failure. nor each crack appearance corresponding calculation being made to assess the redistribution of moment and thrust force in critical section including crown section, section making 45¦ with the vertical etc. De- flection at the above stated critical sections are also measured at each stage of loading. The pressure along the top hori- zontal surface of embedded lining and the vertical sides are measured by pres -sure gauges embedded in sand medium. fhe test results show a complete figure of rupture characteristics of concrete lining embedded in soft ground which approximates alluvial deposite often occur in metro construction at cities near the river side. These test results have been taken as a reference in assessing the action behavior of concrete lining in certain cities in China.

Jan 1, 1987

By E Drueppel, M Mistry, J Pateiro

As mining undoubtedly influences the natural environment future challenges of copper ore mining are minimisation of land use in area and duration, proper land rehabilitation as well as tailings management. One possible solution to avoid these negative impacts could be the application of underground mining with backfilling tailings compounds. This approach would definitely increase the production cost. Against this background the project analyses the influence of an æecologically satisfyingÆ copper ore mining on world market prize and demand as well as on the environment. In the project 261 copper ore mines accounting for 98 per cent of world copper production have been examined. After modelling a backfill plant, analyses of applied backfill techniques were conducted. Afterwards a method of cost estimation was developed and then the backfill plant model was applied in three case studies. The results were transferred into scenarios. The work closes with a short discussion and gives an outlook to forthcoming research. The results presented in this work have been generated within the Collaborative Research Center (CRC) 525 entitled æResource-orientated view of metallic raw material flowsÆ. This interdisciplinary project was established at Aachen University of Technology (Germany) in 1997 and is funded by the Deutsche Forschungsgemeinschaft (DFG). The long-term goal of this research program is the identification of options for the resource-sensitive supply and processing of metallic raw materials. In order to address the sustainable development challenges facing the metals and minerals industry an integrated resource management system is to be developed and tested for important metallic raw materials. Case studies for aluminium and copper are being conducted by the CRC 525 in order to provide useful and efficient tools for decision makers over the entire life cycle of these materials.

Jan 1, 2003

By Miller JD, Ye Y

The Air-Sparged Hydrocyclone (ASH) has been developed for the fast and efficient flotation of fine mineral particles in a centrifugal field during the past decade at the University of Utah. Over the years, the air-sparged hydrocyclone unit has shown promising potential for the flotation of copper porphyry ore, low-grade placer gold and auriferous pyrite ores, various industrial minerals, and fine coal cleaning. Many fundamental studies including the X-ray computed tomography (CT) analysis have been carried out in order to understand the multiphase fluid flow phenomena associated with ASH flotation. With data available from these studies, it is now possible to construct more accurate ASH flotation models for different applications in order to analyse the behaviour of the system and to optimise design and operating variables. The ASH flotation model developed in this paper is based on the data given in `Air-Sparged Hydrocyclone/Advanced Froth Flotation Fine Coal Cleaning', Final Report, DOE Contract No DE-AC-88PC88853, submitted by Pennsylvania Electric Company (PENELEC), December 1989. Data from several hundred experiments with the two-inch ASH-2C air-sparged hydrocyclone (capacity 0.1 - 0.3 tph dry coal) are available from the report and have been used for this analysis. In the past, a preliminary model based on limited data had been developed. The current study, however, emphasises the global behaviour of the ASH system by utilising almost all the data from the report for the purpose of scale-up and industrial application. There are two parts in the current modeling and analysis effort for ASH flotation of fine coal. The first part is the modeling/analysis of dimensionless ratio of overflow opening area to underflow opening area, A*, and the dimensionless ratio of air flowrate to slurry flowrate, Q . The second part involves the modelling/analysis of all other variables in the system and an expert system for operation and control is introduced.

Jan 1, 1993

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

Modelling and Optimisation of Direct Reduction of Iron Ore by Coal in a Rotary Kiln

Sep 13, 2010

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

Modelling and Simulation to Design a Flotation Circuit for Gold Concentration

Sep 13, 2010

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000

Hydrocyclones are widely used in both mining and various industrial sectors. Considerable fundamental research work on the modelling of hydrocyclone classifiers has been carried out through the past 25 years. Based on the similarity principle, the hydrocyclone classification was taken as a whole physical process and a group of similarity numbers were obtained with the help of dimensional analysis in this paper. Then, the functional dependences of the similarity numbers have been established. The variables optimisation was carried out with the multiple objectives linear planning programs developed in this study.

Jan 1, 1993

By O Handayani, R Barr, E Isaaks

The mining industry has focused a great deal of attention recently on the impact of blast movement on grade control. Although the problem of blast movement and its contribution to dilution and ore loss is well known, solutions to the problem are less than satisfactory. Perhaps the most recent innovation is the application of blast movement monitoring (BMM) devices to quantify blast movement. These devices emit an electronic signal and are planted at surveyed locations within the preblast material. Following the blast, their new locations are found using an electronic scanner. The magnitude and direction of the blast movement is given by the vectors between the pre- and post-blast BMM locations. However, it’s not clear how the BMM vector data can be best used to minimise dilution and ore loss. One common solution is to displace preblast dig line polygons by distances indicated by the BMM vectors. However, studies of BMM vectors show that blast movement not only displaces material laterally but also mixes material internally within the bench (Thornton, 2009a).This paper presents a method for modelling the post-blast muck pile that accounts for displacement and internal dilution using simulated annealing. The preblast ore control block model is re-blocked to 1?×?1?×?1?m sub-blocks. Each sub-block is displaced by simulated BMM vectors conditional to post-blast surface topography and blast initiation sequence data in addition to BMM vector data. The displaced sub-blocks are aggregated into new ore control model blocks whose grades are calculated from the contained sub-blocks. New dig lines are then designed on the post-blast muck pile model using the new ore control block model grades. A case study based on actual data is provided.CITATION:Isaaks, E, Barr, R and Handayani, O, 2014. Modelling blast movement for grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Tonnage and grade are the principal reported components of mineral resource estimates but tonnage is a derivative of two more fundamental estimates; volume and bulk density. Typically, most of the effort in a resource estimation study is directed towards grade and volume, yet poor application of bulk density data to resource models can result in significant biases. The impact on tonnage estimates is easily recognised but poor density estimates may also introduce subtle biases into the grade estimates. Methods for measuring bulk density have been discussed previously. This paper focuses on the manipulation of bulk density data and the extension of bulk density from essentially point measurements to block estimates within resource models. Bulk density is a continuous, geologically controlled, spatial variable and should be treated as such. Issues such as combining data from multiple sources, sample support and the interdependence of bulk density and grade estimates must be resolved. The statistical and geostatistical techniques used for grade estimation are, under the right circumstances, equally applicable to bulk density. The importance of bulk density needs to be recognised. With robust raw data and correct estimation procedures, better estimates of bulk density can be obtained and both local and global tonnage and grade estimates can be improved.

Jan 1, 2000

Modelling Channel Scale Flow in Heap Leaching Using Smooth Particle Hydrodynamics (SPH)

Sep 13, 2010

By K Williams, T Donohue, W Chen, T Roessler, A Katterfeld

Wet sticky iron ore poses particular difficulties in every aspect of the material handling process. Material hang-ups in bins, pipes and chutes; carry-back and spillage due to insufficient belt cleaning; clogging of screens; malfunctioning of crushers as well as rat holing of gravity reclaimed stockpiles are all predominantly due to the inherent cohesion and adhesion characteristics of the wet, sticky ore (Roberts, 1993). Limited understanding and quantitative measures on the stickiness of such a material significantly lower the mining operation efficiency.This research aims to investigate the cohesion and adhesion characteristics of the wet, sticky ore on physical modelling, experimental techniques and numerical implementation. Initially, the suitable bridging mechanism that contributes to the cohesive and adhesive forces within the iron ore material was identified (Hering, Martin and Stohrer, 1989; Rumpf, 1958). A cohesion/adhesion energy density factor based contact model was then introduced to describe the stickiness of the material. Secondly, an experimental system was proposed to directly test the stickiness of the material. Such a system is able to obtain both the cohesive/adhesive shear force and tensile force of the material at a specific moisture content. Lastly, the implementation of the proposed cohesion/adhesion model into the discrete element modelling (DEM) software was also discussed. A cohesion/adhesion calibration for modelling wet sticky iron ore in DEM was then conducted to ensure the material modelled in the simulation is reflective of the reality.From the study, understanding of the cohesion/adhesion characteristics of the wet iron ore material is significantly enhanced. Experimental and numerical outcomes can be directly applied for better designing or optimising the material handling processes that involve wet sticky iron ore. Consequently, the mining operating costs can be greatly reduced.CITATION:Chen, W, Donohue, T, Williams, K, Katterfeld, A and Roessler, T, 2015. Modelling cohesion and adhesion of wet, sticky iron ores in discrete element modelling for material handling processes, in Proceedings Iron Ore 2015, pp 387–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Keddie

Standard microeconomic theory suggests that the behaviour of mineral extraction and processing firms with respect to their demand for water can be modelled and a market demand for water subsequently derived. Such a model, although an abstraction of the real world, should be able to predict the responsiveness of quantity of water demanded to change in price, and, change in demand to a range of factors including: expectations about reliability of supply, changed commodity prices for mineral production, and change in water technology and storage at mine site. This paper demonstrates that the price of water is particularly responsive to changes in demand and that although price increases would result in some additional supplies, physical constraints on supply suggest that the industry will be paying considerably higher prices for water in the future. It is recommended that the mining industry undertakes quantification of possible price increases to position itself to minimise the impact on their operating costs as well as to make responsible capital investment decisions to facilitate future expansion or commissioning of new mines. Substantial investment is required to commission a new mining venture with expected rates of return subject to risk and uncertainty due to fluctuations in world commodity markets as well as reliability of secure supplies of inputs. If a reliable supply of water was subject to uncertainty and water was a critical input for production, then the initial mine design would typically consider a range of production decisions contingent on levels of uncertainty with respect to water supply. These states or sets of water supply, will affect production decisions and future water demand. Modelling production decisions contingent on different states of nature, termed the state-contingent approach, provides a number of insights about producer behaviour under uncertainty. This paper investigates the assumptions underlying the derivation of the market demand for water by the mineral resource industry and identifies the drivers of demand and the responsiveness of the industry to change in price and supply, particularly in relation to capital investment in water-use technologies. The usefulness of these models to the mining industry is considered by reference to the increasing demand for water by the industry in Queensland, in a climate of water shortages.

Jan 1, 2006

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By Y Wei, H-B Mnhlhaus

Particles are by far the easiest objects to simulate, because their dynamics is simple. Determining the motion of particles and their interaction, a wide variety of deformable structures can be constructed by connecting particles that have mass, position, and velocity, and that respond to forces. Starting from this simple idea we have derived what we call the particle-lattice method for the solutions of boundary value problems of deformation and fracture of solid mass. The problem of rock breaking by blasting operations as well as fracture and flow of rocks fragments involve momentum transfer between solid and fluid; gas flow and reactive mass transfer. In this paper we outline the method and describe briefly the salient features of the algorithm. We derive relationships between the contact properties for the discrete model and the properties of the underlying continuum and fluid flow coupling procedure. Finally we illustrate the potential of the method by means of example solutions related to the dynamic fracture and flow in jointed rock by blasting.

Jan 1, 1999