Search Documents

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

By S Morgan, A Jakowetz, S Taylor, B Weekes, S Litson, P Bourke, T L. Do

In the current tough mining environment with lower commodity prices, operators need to improve operational profitability. Optimised equipment asset management is a sustainable way to achieve this objective. The increased efficiency of installed process equipment positively contributes to the circuit performance, affecting metallurgical performance, plant availability and operating costs. Nui Phao Mining Company Limited (NPMC) operates a polymetallic mine located in Vietnam. The circuit produces four main products, tungsten, fluorspar, bismuth and copper. Tungsten is the major revenue producer. The operation experienced the following equipment inefficiencies in its copper and bulk sulfide flotation (BSF) circuits:• lower than expected metallurgical performance - the BSF rougher flotation tails contained coarse (+106 µm) sulfur minerals which affected the downstream tungsten gravity circuit. The unrecovered sulfur competed with tungsten minerals affecting both tungsten recovery and product grade. • structural integrity and safety - the flotation circuit structures experienced excessive vibration beyond the acceptable tolerance levels. The vibration was attributed to the flotation mechanism design and impeller tip speeds. • equipment reliability and wear life issues - the flotation mechanisms were being replaced every six months, with reported failures at three months. This resulted in high operational costs. A mineralogical evaluation of the ore indicated that the coarse sulfur minerals were well liberated and relatively rich in pyrrhotite and pyrite. It was predicted that these particles should be recoverable by flotation under optimum conditions. NPMC worked collaboratively with Outotec to investigate options to improve the metallurgical performance of both sulfur and tungsten. A review of the copper and BSF rougher circuit infrastructure was also undertaken and focused on reducing the structural vibration and improving mechanism wear life. Prior to the circuit upgrade, laboratory and pilot testing was conducted to validate the circuit improvements. The final solution included the installation of Outotec FloatForce® mechanisms in the existing copper and BSF rougher circuits, and a new flash circuit (SkimAir®) treating the rougher tails stream ahead of the tungsten gravity circuit. The flash circuit is unique, as typically these types of cells are installed in grinding circuits. By March 2016, all circuit upgrades were complete, however the initial metallurgical performance was below expectations. NPMC and Outotec worked together to investigate and improve performance through further equipment modifications. Since October 2016, the metallurgical performance has improved significantly. Coarse sulfur mineral recovery has improved, resulting in an overall increase in recovery of sulfur and tungsten of 4.7% and 2.7% respectively. The Outotec FloatForce mechanism has also delivered operational benefits, with a reduction in structural vibration to within acceptable levels (<4.0 mm/s) and an improvement in mechanism wear life by 150%. This paper discusses the BSF circuit upgrades and compares operational data before and after the upgrade to quantify the improvements in metallurgical performance, structural vibration and mechanism wear life. CITATION:Morgan, S, Weekes, B, Jakowetz, A, Litson, S, Taylor, S, Do, T L and Bourke, P, 2017. Nui Phao mine – flotation circuit upgrade, in Proceedings MetPlant 2017, pp 230–253 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

The N3500 orebody is the northern continuation of the 3500 orebody at Xstrata Copper's Enterprise Mine and occurs at a depth of 1.3 to 1.8 km. At the nearby S3500 orebody, extreme deformation was observed in access drives where there was a high number of bedding planes per metre combined with either graphite or talc infill. The observed failure mechanism was largely controlled by the geometry of the inclined bedding submitted to high horizontal stresses. Due to the anisotropic strength and deformation behaviour of the shale rock mass, traditional isotropic methods of geomechanical property estimation based upon GSI are not appropriate. A numerical modelling approach, based upon the distinct element codes UDEC (2D) and 3DEC (3D), has been developed to accurately simulate the failure mechanisms and deformation observed in the initial infrastructure surrounding the N3500 orebody.

Nov 25, 2010

By Kuruppu M

Geotechnical design plays a key role in mine design. A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches: (i) judgmental, based on observational and experiential facts, (ii) empirical, based on empirical design formulae; and (iii) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools is provided. The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing mining structures. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis applications in excavation design.

Jan 1, 1995

By Medhurst TP, Trueman R

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface mod- elling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model pre- dicted the fender would suffer considerably more de- formation and strain.

Jan 1, 1992

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

A mathematical model for spontaneous combustion of coal with moisture included is presented in this paper. The one-dimensional unsteady state model consists of conservation equations for oxygen, water vapour and inherent moisture of coal and energy for both gaseous and solid phases. A first order Arrhenius reaction rate for oxidation under both pore diffusion and chemically controlled reaction regime is considered. The rate of evaporation or condensation is also considered as a function of temperature of coal, water content of coal and gas streams. The equation of the model is solved numerically by the finite difference technique. Influences of different parameters on the process of spontaneous combustion can be examined by using this model. Also the model can be used to simulate full-scale storage conditions.

Jan 1, 2005

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

By Kubik K

The objective of this paper was to determine if recent advances in numerical electromagnetic wave propagation modelling techniques could be used to study the propagation of GPS signals over arbitrary terrain. Specifically the effects of diffraction and multipath were to be modelled accurately for propagation over arbitrary terrain surfaces defined by a digital terrain model. Ideally the model was to be in three dimensions and cover an area of a few square kilometres with a simulation height of a few hundred metres. Simulations were to run on current technology PC's with run times less than a few hours. A relatively new technique that involves a numerical solution to the Parabolic Equations can be used to solve for two-dimensional propagation over any type of terrain. The PE provides a direct solution of Maxwell's wave equations by approximating the Helmholtz scalar wave equation. This technique does not rely on the study of individual ray paths as used in the Geometrical Theory of Diffraction (GTD). It was decided to develop a two dimensional Parabolic Equation code, using the Fourier Split/Step method that allowed propagation over arbitrary terrain (; ; ). The model boundary conditions assumed that the satellite transmission was a plane wave, and that the lower boundary was a perfect reflector. Propagation simulations from the model accurately provide the amplitude and phase of the propagated plane wave at all points within the model domain. The PE model was used to study the effects of diffraction and multipath caused by various types of terrain commonly found in an open cut mining environment. The study of diffraction errors was relatively simple, because we are simply concerned with amplitude of the signal as it diffracts about an obstacle. If the amplitude is above the level receivable by a GPS receiver then the diffraction error can be obtained from the geometry of the terrain obstacle. The study of multipath is more complex, as the computed phase from the PE model is ambiguous and the presence of multipath can only be inferred. Thus the absolute magnitude of the nmltipath error is not currently determinable, though the results of some new work is shown here. This paper shows that diffraction effects can cause significant errors in range. It also shows the effects that multipath has on the received amplitude of the signal and the received phase of the signal. A discussion is made of further work that is presently underway that will allow the direct determination of the multipath error by comparing the ambiguous phase with a reference phase.

Jan 1, 1997

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By J W. Lee, E Baafi, N Aziz

Ground subsidence due to mining is a common dilemma confronting the underground coal mining industry. The effects of underground longwall mining on river valleys have come under scrutiny, especially when mining is located underneath catchment areas. As public awareness of mining impacts on the environment increases, there is the need to develop damage mitigation strategies. Results of numerical modelling show that river valley response to underground longwall mining can be simulated and evaluated.

Jan 1, 2005

By B BussiFre, J Molson, M Aubertin, G W. Wils

Waste rock piles containing reactive sulfide minerals can serve as long-term sources of acid mine drainage (AMD). Within these piles, many physical, geochemical and biological processes can contribute to the production of AMD. The flow of water, for example, depends on internal pile structure, which depends on the dumping methods used to construct the pile. In this paper, the internal structure and grain size distribution of typical waste rock piles are first reviewed with respect to their effect on internal water flow. A numerical model is then applied to simulate unsaturated flow within a waste pile assuming two primary waste materials, different atmospheric conditions and several geometric configurations. The simulations suggest that water movement can be controlled by introducing fine-grained material layers within the coarser host material. However, these layers should not be horizontal because they can lead to localised high-saturation regions as well as preferential flow favouring the production of AMD. A shallow slope towards the pile boundary may be introduced to force drainage to the outside while maintaining low saturation within the interior, thus reducing the production of AMD.

Jan 1, 2003

The paper describes a simulating method.for ground water contamination originating from industrial and mining activrty. The finite difference model simulates heat, mass and solute transport. The applied stochastical method for dispersion provides more accurate solution of mass transport modelling. This method gives a more realistic approach of chemical processes in an aquifer depending on temperature.

Jan 1, 1988

By S Servant

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the stope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the stope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this mine.

Jan 1, 1998

By Servant S

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the scope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the scope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this Mine.

Jan 1, 1998

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The title of my presentation is `Nursing One's Resources', words that fit a young organisation like Ross Mining and words we had to apply to reach our current level as a company. To get to where we are, we had to nurse, foster and treat carefully all our available resources in the widest sense of the word, namely: ò a stock or supply that can be drawn upon (funds, mineral resources, human resources); ò the means available to achieve an end; ò skills in devising expedients; and ò practical ingenuity. I do not claim that Ross Mining is now the perfect mining company. However, we have become a profitable, dividend- paying, gold mining and exploration company which is to our knowledge, currently the cheapest gold producer on the Australian continent. Nursing our resources got us where we are and will guide us in our future development. The words `nursing one's resources' are I feel particularly applicable to mining-as I like to argue that the extractive mining industry has a social responsibility to optimise the metal output and value from each orebody which is being exploited, and preferably leave no metal behind. Likewise, a modem company cannot survive into the future without maximising and optimising its human resource potential. In this presentation I would like to present a number of actual examples of nursing one's physical and human resources. Before I do that, I will give a brief background to Ross Mining. Ross Mining NL is a young Queensland-based company that gained its stock exchange listing in September 1987 and that poured its first gold in 1989 from its own developed Belyando Mine, located in Central Queensland. We have now reached the stage of a medium-size gold producer, producing approximately 70 000 ounces of gold per year, mainly from the Yandan Gold Mine, also in Central Queensland. Our production is set to increase to over 100 000 ounces in the near future. Recent increases in our resource base have secured us a future of ten to 15 years. As a young, newly listed company, we faced all the dangers that most new small floats do as a new entrant into an established industry. However, one advantage of being young and perhaps naive, is summed up by the following Zen Buddist saying: In the beginner's mind there are many possibilities, in the expert's mind there are few. A mining company's main assets are the sum of its resource base and the skills and talents of its people. Attempting to optimise both the physical and human resources within the company has been to-date the key to our success. The first example I would like to present is linked to the exploitation of the Belyando Gold Mine in Central Queensland.

Jan 1, 1995

By B Kretschmer, G Bartel, B de Villiers, W Watt

"The Nyrstar Port Pirie Smelter, located on the eastern shore of the Upper Spencer Gulf in South Australia 230km north of Adelaide, began operation in 1889 to process lead concentrate from the Broken Hill lead and silver mines. The site still operates an updraft sinter machine, commissioned in 1955, with the product fed into a blast furnace. While sinter plant technology has changed and improved since 1955, development has reached the stage where further enhancements are not possible or economic. High purity lead concentrates command lower margins and for the smelter to remain economically viable a wider range of higher value materials must be treated. The current flowsheet cannot meet this demand. Additionally, community blood lead levels particularly in children below four years of age, are a critical indicator used to measure the site’s environmental performance. The smelter’s environmental licence to operate is dependent on meeting future community and regulatory expectations. To achieve this a major step change in the emission performance of the smelter is required. Since 2008 pre-feasibility work has been undertaken to develop a new flowsheet and business model to allow Port Pirie to operate sustainably into the future. The main requirements were for the smelter to reduce lead and sulfur dioxide emissions that impact on the local environment and community to meet current and future environmental expectations, as well as dramatically reducing current feed constraints and change the business case from a marginal business to a sustainable profitable business. After reviewing all practical options a decision was made to replace the sinter plant with an Outotec Top Submerged Lance (TSL) furnace. This paper describes how the new furnace technology was selected and how it will be integrated into the present flowsheet; the unique funding arrangements that are in place to deliver the redeveloped site; and future opportunities that are associated with the implementation of the new flowsheet. CITATION: De Villiers, B, Bartel, G, Watt, W and Kretschmer, B, 2015. Nyrstar Port Pirie redevelopment, in Proceedings MetPlant 2015, pp 325–337 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 7, 2015