Search Documents

By Tzung-mow Yao, S Ki, J Word, J Vinson

Properly designed evapotranspirative (ET) cover systems can greatly reduce the amount of infiltration and groundwater recharge (deep percolation) into potential acid generating mine waste. In arid and semi-arid environments, infrequent precipitation, low measurable subsurface fluxes, spatial variability within mine waste and cover material, and evapotranspiration from below the cover system create challenges to monitoring moisture flux in these systems. Sloped ET single-layer (monolayer) cover depths and a variety of reclamation treatments are being studied at a copper tailing impoundment in Arizona, USA. To monitor the performance of different ET cover systems in response to precipitation patterns, four different test plots consisting of two different cover depths and two different vegetation densities were instrumented with heat dissipation sensor nests. The sensors measure the soil water pressure potential and allow hydraulic gradients to be determined within and below the cover systems to depths of 180 cm. Three replicate sensor nests were installed in each test plot to account for variability in materials and test plot treatments. Data collection occurs twice daily and is ongoing. Weather during the 26-month monitoring period was characterised by two months of greater than normal precipitation followed by nine months of normal precipitation and 15 months of abnormally dry conditions. Monitoring data indicate that deep percolation occurs in response to periods of extended precipitation, however, drying was observed to depths of six feet below the surface in all test plots. Using conservative assumptions regarding tailing hydraulic properties, one-dimensional downward flux predictions based on the monitoring data indicate very low (Additional long-term monitoring and installation of deeper and replicate monitoring sensors into tailings without cover systems are recommended to evaluate the long-term ET cover system performance and develop a better understanding of deep percolation rates at the sites.

Jan 1, 2003

Performance of Outotec FloatForce« Flotation Mechanism - A Study in Both Computational Fluid Dynamics and Industrial Scale Measurement

Sep 13, 2010

By OÆBrien D, Priddle D

In order to avoid costly moisture penalties on coal shipments and to minimise rail freight costs, screen bowl centrifuges were selected and installed in the Mount Thorley Coal Preparation Plant for dewatering fine coal product. The Mount Thorley fine coal circuit consists of desliming the -0.5 mm (ww) fine coal in two stages of classifying cyclones prior to recovery by froth flotation. Provision has been made to bypass the flotation circuit with the classified flotation feed reporting directly to product and the centrifuge dewatering circuit has been designed to handle either flotation feed or flotation product. Major mechanical failures of the gearboxes and the ceramic tiling occurred early in the operation life of the machines which led to design changes being made to achieve satisfactory operation. This paper discusses the operating experience at Mount Thorley with respect to both mechanical and metallurgical performance of the screen bowl centrifuges since their installation in 1985.

Jan 1, 1989

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

Estimation of the semi-variogram is basic to the geostatistical processing of data. The most widely used arithmetic average estimator is here employed with various sampling patterns to calculate experimental semi-variograms in a deposit which is simulated to have a defined semi-variogram. Percentage differences between theoretical and experimental semi-variograms are reported.

Jan 1, 1984

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By E McLean, J Fleay, M Davis

Performance testing is often used by project owners and financiers to provide protection from, or assessment of, technical aspects of project design, procurement, construction and commissioning. The performance tests can range from comprehensive performance warranties relating to process performance and production in the case of lump sum turn key (LSTK) projects to less onerous demonstration tests for cost reimbursable contracts. This paper will discuss performance testing from both the contractorÆs and ownerÆs perspectives and focuses on: when performance tests are required, what type of performance test/warranty is optimum for each type of project, and how project performance should be evaluated. The requirement for performance testing can be driven by the project financiers, particularly in the case of smaller resource development companies. In such cases, differentiation between ownerÆs risk and contractorÆs risk can become contentious. At the other end of the spectrum, larger mining houses may choose to heavily influence the engineering and design process with the contractor supplying services on a reimbursable basis. In that case, the performance testing process is often limited to demonstration tests that validate performance for the ownerÆs corporate governance requirements. This paper was prepared due to the lack of published benchmarking of performance testing and the resultant differences in expectations between a contractor and a project owner that often surface late in the contract negotiation process. The paper provides a checklist of requirements for both the owner and the contractor that may be used to provide æcommon purposeÆ early in the contract negotiation process.

Jan 1, 2007

The Mt Whaleback open cut mine South Wall is, in part, developed as an unbenched dip slope. The remainder of the rock slope consists of asymetrical overturned folds which have been locally truncated by major low angle faults. The Mt Whaleback orebody is structurally controlled and therefore extensive structural geology input has gone into the final rock slope design. The design is based on normalised 40 m geological cross sections, but the inherent complexity of the geological structure of the orebody yields a high degree of uncertainty within that interval. There- fore, the final slope bench face and the penultimate bench faces are mapped in detail to accurately establish the geological contacts and struc- ture. The knowledge of accurate geology of final and penultimate faces plays a very important role in the design of controlled perimeter blast- ing. Accurate geology is established mainly by face mapping, and by hole geological evaluation of blastholes to locally refine the current Geologi- cal model.

Jan 1, 1989

By A J. Tucker, L Bottomley

The principle objective of development mining is to create thoroughfares that can be accessed by personnel and machinery for the entire life of an underground mine. The drill and blast process, being the primary method used when creating these thoroughfares, needs to be able to adequately fracture the rock to be removed whilst at the same time minimising any damage that may be sustained to the rock surface that remains. This process of damage prevention is known by a variety of different names including smooth blasting, sculpture blasting, contour blasting and controlled blasting. Whilst the terms are different, the objective is the same and that is to reduce and better distribute the explosive charges to minimise stressing and fracturing of the rock beyond the neat excavation line. The process in this report will be referred to as perimeter control blasting. This paper will discuss the benefits of using perimeter control blasting in a development mining operation and the theories that govern how these blasting techniques work. The methods that are used to implement perimeter control blasting will also be addressed, paying particular attention to how these blasting techniques have evolved, spawning new and improved perimeter control products. Finally some attention will be given to the process of optimising perimeter control blasting in any underground mining operation.

Jan 1, 2005

By J Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration in small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using e-Dev™ electronic detonators in a typical mining application was conducted at Resolute’s Mt Wright operations in North Queensland in 2010. Results were based on direct comparisons to the current industry standard of non-electric firings as a baseline, with as many parameters as possible being captured during the trial. Development costs are typically high in most underground mines, especially in capital development headings, which are in waste and therefore of no direct economic value, so by being able to accurately fire to design, costs relating to both ground support requirements and volume of material removed, (and therefore haulage required) can be minimised. A direct comparison of overbreak (ground blasted outside of design) and cast (distance rock thrown from blast) was also made during the trial, as well as close monitoring of the drilling accuracy.

Mar 21, 2011

By P Bethune

Back Creek is a tributary of the Condamine River. It flows in a northerly direction across the existing Commodore coal reserves. The diversion of Back Creek was proposed to minimise sterilisation of the reserves. The approval process required a Waterworks Licence application, under the Water Resources Act 1989 (Qld), for the construction of a stream diversion channel and floodway. The diversion was designed using the æreference reachÆ approach, which mimicked existing properties of Back Creek. The following design standards were developed for the diversion: the diversion corridor width was 500 m; the diversion geometry was specified for both the low-flow channel, and the floodplain; material properties were specified for both the low-flow channel lining and the diversion bund; compaction standards for both the low-flow channel and floodplain were set; and the diversion rehabilitation included a riparian corridor and pasture land with clumps of native trees and shrubs. The following performance criteria were developed for the diversion: velocity regimes were replicated for the design events considered, in an attempt to avoid increasing the diversion flow velocities in comparison with the existing creek flow velocities; sediment transport calculations indicated that no significant change in sediment transport was expected within the diversion; overburden settlement estimates for the spoil placed in the corridor were summarised, and will be monitored throughout the construction process; geotechnical stability of the proposed Eastern Pit Buttress and the diversion bund configurations was confirmed; and groundwater impacts were assessed. Construction techniques, monitoring and further investigations are also discussed in this paper.

Jan 1, 2003

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

By R Bertuzzi

Permanent rock bolts in civil engineering are taken as having to serve their design purpose for at least 50 years. In many projects the design life is specified as greater than 100 years. A review of recent Australian tunnelling projects shows that substantial differences exist in the level of corrosion protection provided for permanent steel shafted rock bolts. This paper reviews the current state of practice and sets out what the authors consider to be appropriate requirements for corrosion protection.

Jan 1, 1999

By J D. St George

In this paper a laboratory investigation into the effect of confining stress, water content and gas desorption on coal permeability is presented. Of major significance is the effect of coal permeability on outburst occurrence and methane production, which is influenced by changes in stress. Test results indicated that the shrinkage of the coal matrix associated with desorption is greater than the coal matrix compressibility which will cause a reduction in the effective stress, hence increasing coal permeability.

Jan 1, 1998

By J M. Totterdell

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid-Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian-Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

By Totterdell JM

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid- Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian- Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

Factual data about the sedimentation in the Newcastle Coal Measures are presented. Data concerning the total coal measure sequence (isopachs, sand/shale ratio, and total coal thickness variation), data about three coal seams (Borehole, Dudley, and Victoria Tunnel) and data about interseam conglomerate units are discussed.From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature, was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin.The northern and north-eastern edge, which was unstable, supplied most of the coarse detritus (including the conglomerates) to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern- each show development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure.Evidence of ill situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.The unusual character of this coal basin, in particular the very coarse units, is stressed, despite the presence of many "normal "coal basin features.

Jan 1, 1970