Search Documents

A Master of Applied Science degree course in Mining Geomechanics commenced in 1983 at The University of New South Wales, taught by extern- al (correspondence) studies. The course is aimed at graduates employed in the mining indust- ry, and especially people involved in geomechan- ics projects on a routine basis in remote locations. This kind of course is unique in Australia and is one of only two correspondence programmes available at this University. The author designed the course and nursed it through the early years, and was Director until 1986. The paper describes the teaching and assess- ment methods and also discusses aspects of admin- istration and coordination of such a course. It is concluded that an important need of the mining industry is being catered for and it appears that similar correspondence course for- mats would also be useful in other areas of the minerals industry.

Jan 1, 1986

Alluvial gold mining is thriving in the Yukon Territory and Alaska. The scale of many operations is similar to those in New Zealand but there is greater government support for research and test work. As a result a great deal of information on equipment for the recovery of alluvial gold has been obtained. This paper is a review of the information with the aim of making relevant data available in New Zealand.

Jan 1, 1989

By P W. Wypych

The iron ore industry faces significant challenges in the control of dust to meet emissions regulations and goals, as well as ensuring sustainable operations. This paper describes some of the different techniques and innovative technologies that are being developed and implemented to improve the suppression of airborne dust, specifically through the use of high energy micromist sprays. The utilisation of computational fluid dynamics (CFD) modelling and simulation is identified and described as a key enabling technology for an improvement in dust suppression solutions both from a level of understanding the source and flow of dust emissions, and for the development of new systems that can be used in the iron ore industry. CFD modelling is shown to be effective for modelling both spray dispersion and cross-wind effects, allowing designers to develop high-efficiency dust suppression systems with a greatly improved level of confidence when compared to traditional techniques. New high energy micromist technology is also outlined as a key element in developing high-efficiency dust suppression systems. Experimental results and industry applications are presented to demonstrate the significant improvements that can be achieved in suppressing or reducing airborne dust emissions.CITATION:Roberts, J M and Wypych, P W, 2017. Research into improving the efficiency of water spraying airborne dust control techniques in the iron ore industry, in Proceedings Iron Ore 2017, pp 359–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Zhijing Z, Huiling Z

The influences on flotabilities of dolomite and magnesite with modifiers and influences on the function of collectors and modifiers with Mg+z Ca+2 were studied. The flotation results of artificial mixed mineral showed that using combined salified water glass and (NaPO3)6 as a modifier for magnesite-dolomite separation can obtain an excellent Selectivity.

Jan 1, 1993

By Whiteman P. C, Stacey G. S, Hunter G. D

Processing of lead-zinc and copper ores by Mount Isa Mines Limited produces large quantit- ies of concentrator tailings waste which is pumped as a slurry to special dams where the solids are allowed to settle and dry out. These areas are unattractive and show no signs of encroachment by plant life even though the surfaces of some dams have remained undisturbed for more than a decade. During 1970 Mount Isa Mines Limited commenced a long term research program in conjunction with the Department of Agriculture, University of Queensland to deter- mine possible methods of establishing a plant cover on this material. Research has defined the major factors limiting plant growth in the tailings medium. Modification of the edaphic conditions through fertilizer inputs, particularly of phosphorus and nitrogen, and alteration of "soil" physical properties by incorporation of mulching mater- ials, provided conditions which allowed plant growth. The outstanding "soil" amendment treatment was incorporation of fly ash, a waste product of the company's coal fired power stations. A range of crop and pasture species have been selected which have grown well with adequate irrigation under the amended conditions in the field. Further research is assessing a range of native plant species and agronomic techniques to provide a stable plant cover on the tailings dams.

Jan 1, 1974

Legislation introduced for Queensland and New South Wales Coal mines provides different levels of prescription regarding specification of mine seals û generally in relation to capacity to withstand overpressure. In Queensland, the Coal Mining Safety and Health Regulation (2001), Section 341 (d) places a further onus on the statutory ventilation officer to æensure all ventilation control devices at the mine are properly constructed and maintainedÆ and that the ventilation officer æmust ensure a ventilation control device mentioned in the regulation à and installed at the mine meets the design criteria statedÆ for the ætype of deviceÆ. Based on the experience of the author, it appears that risk management and life cycle approach to seals has not been adopted to the same extent as for other aspects of operations. Further, because of the number of disciplines and personnel involved that may influence various factors affecting seal integrity, the opportunity for oversight or unclear allocation of responsibility is considerable. While suppliers can provide explosion or design rated seals, this should only be a starting point for application of the product in a coal mine. Application is often considered by mine planning staff (taking into consideration mine environment parameters such as water, control of gas, spontaneous combustion risk, etc) in conjunction with the colliery ventilation officer, and then construction completed by contractors under supervision of operational staff. After construction, seals often are managed by operational personnel with input from the ventilation officer. Input of the geotechnical engineer into pillar design, roadway opening size, ground support specification and most stable seal location is also required. The need for a customised design approach for each seal site is proposed in order to take into account the many and variable factors that may influence a site so that improved seal performance reliability and predictability can be developed. A program of quantitative as well as qualitative monitoring of performance and triggers for rectification or maintenance action is required, and would provide support to the aforementioned proposal. Many mines rely on visual/audible inspection and periodic bag sampling as the primary means of assessment. Other significant factors such as seal material properties, rib degradation, convergence, floor heave, effects of water on both structural integrity of the seal as well as the air tightness of the seal do not generally receive the same level of attention. Based on the above observations, the author has compiled a reference checklist in regard to the above matters, including aspects of and approaches to mine and pillar design, geotechnical modelling and data collection, civil engineering design, site evaluation and practical options available.

Jan 1, 2005

Research of 200 m3 Self-Suction Flotation Machine

Sep 13, 2010

By Guoqing Cao, Xinghong Wang, Fuqiang Liu, Rong Shen, Xiaoping Yuan

In this paper, an approach is proposed to monitor the rate of lump coal based on image processing. Using this method, we effectively improve rate of lump coal on comprehensive mechanised coal face.

Jan 1, 1998

By Hongzhen Yu, Xiaoping Ma, Jiansheng Qian

The paper introduces the design of an Intelligent Managerial Attendance Machine (IMAM) for coal mines. In the system, data communication is carried by Optical fiber communication, including industrial control computer on the ground and the car

Jan 1, 1998

By Lama RD

The paper outlines the development in the control of dust in Australia over the last 20 years. Factors influencing dust make at the faces are discussed. The effect of high production systems is analysed. Changes in dust standards and results of dust sampling on longwalls and continuous miner panels are given. Research conducted on air curtains and water infusion on dust control on longwall faces is presented along with recommendations for future research. It is found that both dust curtains and water infusion can cut dust mak by 50" each when applied separately.

Jan 1, 1988

By X Li, R Chu, X Deng

The hot-dip galvanising industry is the largest consumer of zinc, with over 40 per cent of the world’s total annual production of zinc used for galvanised steel. The dross generated in the hot-dip galvanising coating process is a valuable co-product, since it contains high quantities of recyclable metal. A new method to recover the metal from the industrial galvanising dross was proposed using supergravity separation. During the hot-dip galvanising process, the presence of zinc dross has a serious impact on the surface quality of the hot-dip galvanised sheet, forming zinc dross defects. To reduce the impact of zinc dross, the zinc dross on the surface of the zinc pool needs to be manually or mechanically removed at regular intervals. However, during the dross removal process, a large amount of metal zinc is inevitably carried out, resulting in low zinc utilisation rate and high zinc loss rate. This article proposes an efficient and low-cost technology for the recycling and utilisation of hotdip galvanised dross, which uses super-gravity technology to recover hot-dip galvanised dross online. The metal in the hot-dip galvanised dross returns to the zinc pot in situ, while a small part of the dross remains in the super-gravity equipment, which can reduce the amount of zinc dross by more than 60 per cent and achieve a reduction in zinc loss from 17 per cent to less than 7 per cent.

Jun 19, 2024

By Q-c Li, G-l Gao

Cyanided tailings produced by gold processing operations may cause environmental problems, because they contain pollutants such as arsenic, sulfur and cyanide compounds. Moreover, tailings containing economic metals such as Au, Ag, Cu, Pb and Zn, are potentially valuable resources. In this article, cyanided tailings are catalytically oxidised by nitric acid in the presence of air or oxygen. The resulting solids may be leached to recover Au and Ag. The solution can be used to prepare ferric sulfate or iron pigment. Gases released in the reactions were recycled and reused by oxidation and absorption. All of these greatly improve metal recovery and the reuse prospects of cyanided tailings. Under the following conditions where the initial temperature of oxidation is 80¦C; initial concentration of nitric acid is 30 per cent (by weight); feed proportion (nitric acid to cyanide tailings mass ratio) is 3:1 and reaction time is two hours, the conversion ratio of cyanided tailings is 90.06 per cent. At the same time pyrite in the cyanided tailings is oxidised effectively, gold recovery is as high as 92.3 per cent and nitric acid loss per cycle is only five per cent because of NOx recovery.

Jan 1, 2007

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991

Research on Reduction-Magnetic Separation of Bayan Obo Ore

Sep 13, 2010

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Research on the Design and Processing Characteristics of 320 m3 Air-Forced Mechanical Flotation Cell

Sep 13, 2010

Research on the Differential Flotation of Iso-Floatable Lead-Zinc Sulfide Ore

Sep 13, 2010

By Hang G, Hongtian X

In this paper, it is briefly introduced that China's Ordovician limestone confined-water menaces coal mining and Ordovician water is prevented and cured to secure the safety of coal mining. The theory of "Down-Three-Zones" is presented on the basis of research and practice in recent ten years. The concept of "Down-Three-Zones" of floor water-eruption is described clearly. Finally, the principle and method of applying the theory of "Down-Three-Zones" are discussed. 1. An Introduction of Damage: China is rich in coal resources. The conditions of coal field geology are quite complicated. There is an area of two million square kilometre of Karst limestone in nine million six thousand square kilometres of territory. The resources of underground water are rather plentiful, but this menaces coal exploration. Sixty percent of coal mines in China are damaged by limestone confined-water in different scales, particularly coal mines located the Carboniferous-Permian coal fields of the Ordovician limestone distribution area of Northern China. Because there is the 500-800 metre thickness of Ordovocian limestone and the well developed Karst containsl plentiful water, Karst water can have more than 100 Kg/cm pressure. Limestone aquifers have only distances of several metres or several decade metres to coal seam, Karst water can enter the aquituge and even the coal seam, large eruptions often occur. For example, a mine of 3 million ton production capacity had an eruption of 2053 cubic metres per minute. This is the largest confined-water eruption which has brought enormous economic damage and threatened the safe production of coal mining. Therefore, the prevention and cure of Ordovician water has immense advantage to the development of the coal industry. There are several decades experience in the prevention of Ordovician water-eruption in China. The prevention of Ordovician water-eruption has two kinds of plans. 1) dewatering and depression: it refers to dewatering of aquifers as roofs of seam and depression of aquifers as floors of seam in mining areas. 2) comprehensive prevention under the condition of having water pressure in aquiters. Due to enormous water, electricity, equipment and lots of other factors, the former isn't used extensively, the latter tits to China's actual conditions and is used widely. So-called comprehensive prevention under the condition of

Jan 1, 1988

By G J. Zhang

The shape and particle size distribution of caved ore mass in sublevel caving were investigated in this study. The paper first reviews the main factors affecting the shape and characteristic of caved ore mass in sublevel caving and then through the experimental blast testing with cement-sand concrete models, the shape and particle size distribution of caved ore mass were found out. The experimental results indicated that the shape and particle size distribution of caved ore mass was similar to that of the drawn loose body. This finding presented a new perspective for the future study on the ore drawing theory and on the optimisation of structural parameters of sublevel caving. The structural parameters must meet the principle that the shape of the drawn body is in consistency to the shape of caved ore mass.

Jul 11, 2011

Using a new type of laser surveying instrument named Particle Dynamics Analyser (PDA), the distributions of the radial and axial components of the mean velocity, the size and the concentration of solid particles at selected positions within a transparent hydrocyclone were directly measured out for the first time, from which profiles of the flow field of solid particles were obtained. And some new points were put forward such as the locus of zero vertical velocity (LZVV) of solid particles was not the same as that of liquid, and some particles in inner helical flow could also be separated. The results are of great significance to farther ascertain the separation principle of hydrocyclones and improve the separation efficiency.

Jan 1, 1993