Search Documents

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By Tapponnier P

In North Vietnam, large ductile shear zones are observed along the Red river fault and the Dienbien fault. Left-lateral sense of the Red river shear zone is related to the direction of shortening E-W. NE dipping foliation planes is subvertical. Stretching lineation is subhorizontal ( 25¦). Left-lateral slip observed in the Oligocene Yansun granites demonstrates the major tectonic phase in Neogene, The stress field established from microfaults observed in triassic limestones, Oligocene granites and Neogene Conglomerates. Measurements of striations on fault mirors are used for calculating the stress tensor and for separating tectonic phases. Two tectonic phases in tertiary are separated : first tectonic phase related to the compressive direction E-W corresponds to the major tectonic phase represented by NW left-lateral shear zone. Second phase having the compressive direction N-S associated with the right-lateral movement of the Red-river fault zone opening of the Eastern sea and the Red-river and the Red-river delta is associated with the left-lateral movement along the Red-river.

Jan 1, 1990

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

In the latter half of 1973 a contract was given to Roberts-Holland Joint Venture for the stripping of the southern exhaust airway.The contract was carried out efficiently and relatively cheaply. It was completed 2 months ahead of schedule.The sinking stage and in particular the drilling jumbo proved to be a success and helped produce an above schedule stripping rate.No major problems were encountered with ground conditions or ventilation. A survey of the shaft showed the diameter to be within the set limits of 5·49 m ± 0·15 m.

Jan 1, 1974

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By Adams R. W

A commercial scale strong acid leaching plant was commissioned at the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, a member of the Pasminco group of companies, in February 1988. It was designed to upgrade the lead/silver residue product from 26% to 37% lead, thus improving the realised value and increasing overall zinc recovery. This in turn enables the lead smelter treating the lead residue to improve its productivity. The equipment consists of two 250m3 bricklined leach tanks and two 6.5m diameter stainless steel high rate thickeners operating with counter current washing at 95¦C and 120 g/L H2SO4. The present filtration and drying equipment is also being replaced. Two 35m2 squeeze action filter presses equipped with horizontal plates are being installed, together with ancillary drying equipment to ensure that the final product complies with the transportable moisture limit. The new filtration plant is due to be commissioned in mid-1989.

Jan 1, 1989

By N Arrys, A Jani, S Shahin

Optimising pit slope stability and reducing strip ratio of a mining operation are two key tasks in geotechnical engineering. With a growing demand for minerals and an increasing cost associated with extraction, companies are constantly re-evaluating the viability of mineral deposits and challenging their geological understanding. Within Rio Tinto Iron Ore (RTIO), the Structural Geology (SG) team investigate and collect critical data, such as point based orientations, mapping and geological inferences from adjacent pits to remodel deposits where previous interpretations have failed to account for structurally controlled slope failures. This work outlines the key methods utilised by the Structural Geology team which form the foundations of informed orebody knowledge and subsequent geotechnical design recommendations. This publication utilises the results from a recent analysis to highlight the benefits of this methodology and how it has impacted the economics of an operation through optimisation of a pit wall ‘cutback’ and crest relocation.

Sep 1, 2024

By R M. Stephenson

Large diameter raise boring is a common raise excavation method in the Australian mining industry. Geotechnical investigations were conducted on several large diameter raise bore projects at Gwalia Mine to assess the potential for instability and potential back-reaming problems. A thorough geotechnical analysis and subsequent back-analysis was conducted on a vent raise excavated at 5.5 m diameter and 810 m length.The geotechnical investigation for the vent raise included collection of data from an acoustic televiewer survey that was conducted on the pilot hole. The survey results provided structural data and an insight into the effects of stress on the pilot hole. Structural analysis was conducted using a combination of information obtained from the acoustic televiewer survey and geotechnical logs of the diamond drill core drilled close to the site.Further information was collected from drillers’ plods from pilot hole drilling and back-reaming to conduct a back-analysis of the completed shaft, and this was compared with the structural analysis.The key finding from this review was that the acoustic televiewer survey of the pilot hole accurately identified locations with blocky conditions. This is an important supplement to the information available from the main geotechnical investigation hole, as this was offset from the shaft location over most of its path.CITATION:Stephenson, R M and Sandy, M P, 2014. Structural analysis of acoustic televiewer logs for large diameter raise bored shafts, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 89–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Hellsten KJ, Butt CRM

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By L Xiong, W J Shi, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Baizhangzi gold deposit is located in the northern North China Craton. The structural and lithological controls on the location and geometry of orebodies were studied through geologic survey, ore spatial configuration analysis and structural analysis. The orebodies of the deposit comprise auriferous quartz-sulfide veins and disseminated gold-bearing sulfides. The auriferous quartz-sulfide veins are dominantly hosted by the NNE- (and NE- and NW-) trending faults, which are subsidiary structures of the regional NNE-trending F2 fault. The subsidiary NNE-trending faults, having sinistral reverse kinematics, are associated with the sinistral reverse kinematics event of the F2 fault, which happened under a regional S–N-oriented compression stress field. The subsidiary NE- and NW-trending faults appear to be compressive and extensional respectively. These NE- (and NW-) trending faults are restricted to the granite intrusion and are associated with a sinistral strike-slip event of the F2 fault, which reactivated under a NW–SE-oriented compression stress field. It makes significant influence on geological evolution and distribution of different ore types that the strike of the F2 fault presents significant transition from NNE- to NE-trending in vertical. The ore-bearing disseminated host rocks, with widespread silicification and pyritisation, distribute in the lower inner contact zone of the granite intrusion, especially in the lower wavelike boundary of granite intrusion.CITATION:Xiong, L, Wei, J H and Shi, W J, 2015. Structural and lithological controls on the location of orebodies in the Baizhangzi lode gold deposit in western Liaoning Province, China, in Proceedings PACRIM 2015 Congress, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

Design of cemented fill in mining is often carried out without any consideration of the structure of the fill. The composition of cemented fills varies in the stopes due to the placement method, and the strength of the fill in the laboratory depends on the density, orient- ation, moisture content and drainage conditions. Within each stope there are definite zones and the structure of both cemented rockfill and cemented hydraulic fill has to be defined for each zone and the field conditions simulated in the laboratory. Structure also affects fill permeability and compressibility. From a study of the cemented fill in place, the effect of changes in the placement methods can be seen and then controlled to improve fill performance and economy. These features of cemented hydraulic fill and cemented rockfill behaviour are discus- sed and illustrated through reference to field and laboratory work undertaken at Mount Isa.

Jan 1, 1973

Integrated geological interpretation of aerial photographs and Landsat images revealed that the gold mineralisation at Kyauk Pahto took place in a narrow zone of tension fractures within part of a previously unrecognised dextral wrench fault system. The latter is the wider manifestation of the well known Sagaing (right-lateral) strike-slip fault which has a length of more than 1 000 km, and it demarcates the boundary between the Indo-Australian and Asian plates. A subtle, right-handed kink affects the full width of the Sagaing Wrench-fault System at about the latitude of Kyauk pahto, and the extra dilatancy imposed on the tension fracture zone facilitated episodic ingress of mineralising hydrothermal fluids by "seismic pumping".

Jan 1, 1987

By J Mauk, J Rowland

The Karangahake epithermal Au-Ag mine consists of two main lodes, the Maria and the Welcome/Crown hosted in Miocene andesites. Mineralisation is strongly constrained to major structures and is genetically linked to dynamic tectonic processes. Two main periods of faulting are represented in the deposit: 1. NE striking right-lateral/normal oblique linked spatially and temporally with the mineralising system, and 2. ESE striking right-lateral/normal oblique post-mineral faulting that displaces the lodes. Paleostress analyses performed on a limited kinematic data set indicate NW-SE extension during the formation of the vein system. Veins and lodes strike NNNE and accordingly contain a strike-slip component. The kinematics of vein formation at Karangahake is broadly consistent with that of other deposits within a NNE-trending belt of deposits. Oblique shear on deflecting structures will create zones of compression and dilation. Dilatant zones created on steep structures create fluid pathways potentially focussing large volumes of fluid from deep parts of the system into dynamic structures.

Jan 1, 2003

By D Howe, J Conn, J G. McLellan, K Gates

The Red October Gold Mine, owned by Saracen Gold Mines Pty Ltd, is located approximately 80 km south of Laverton, Western Australia. It is considered to be of a similar nature to many of the Archaean granite-greenstone deposits in the Laverton Tectonic Zone, and presents as an intriguing and relatively young deposit in terms of developed structural and genetic models. Regional deformation events have been proposed for the area, and are relatively well accepted. The most important of these deformation events in the region were the D4b (WNW–ESE sinistral transpression) and D5 (ENE–WSW dextral transpression) which have been attributed to the main Au mineralising phases. At the local scale there appears to have been a rotation of the regional stress field to provide the optimum orientation of maximum principal stress for sinistral movement on the main shear zone.Fully coupled 3D finite element analysis (FEA) was used to simulate the geomechanical response of the system based on structural observations. The geomechanical modelling resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two main deformation events. The D4 simulation provided a good correlation with the known distribution of subsidiary structures on the main shear zone, and furthermore provided several geomechanical targets that suggested locations of additional subsidiary structures. The D5 simulation provided a great insight into the response of the main shear zone and known subsidiary structures also highlighting additional targets indicating potential for further mineralisation. These targets have since been followed up with a 732 m deep surface reverse circulation (RC) drill hole, resulting in the discovery of two high-grade shoots, with follow up testing currently planned for mid-2014.CITATION:McLellan, J G, Conn, J, Howe, D and Gates, K, 2014. Structural controls and strain partitioning in the Red October Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By V Morand, W R. H Ramsay

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (D1) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with D1 and the plunge of the F1 fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late D1 . d18O values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995

By Ramsay WRH, Morand V

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (Dl) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with Dl and the plunge of the Fl fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late Dl. S'80 values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995