Search Documents

Increases in mechanisation and mining at greater depths are leading to additional problems of heat and humidity in many mines. As a result there is now an escalating demand for temperature prediction simulations appli- cable to underground environments. After a brief review of the present situation with regard to world mining and the use of environmental programs, the paper goes on to discuss in moderate detail the mathe- matical modelling of the many parameters that govern the condition of the ventilating air in a mine. The development of a program that gives the temperature distribution for a mine ventilation system is then outlined. The practicality of the program is discussed and the presentation format for users is explained. Simplification of input data requirements and the acquisition of data from other planning programs are an integral part of the commercial application of this program.

Jan 1, 1977

The Ida Valley in Central Otago is one of series of parallel basins filled with freshwater sediments. The basins are in fact tectonic depressions superimposed on NE trending grabenlike structures which occur in the area and are the result of block faulting possibly initiated in Cretaceous times and concluded in late Tertiary and early Quaternary. In Central Otago this tectonic event affected metamorphosed rocks belonging to the eastern facies of the New Zealand Geosyncline and collectively known as the Haast Schist Group. These rocks constitute the basement and the shoulders of the tectonic depressions. The Ida Valley occupies the depression wedged in between the Raggedy Range to the NW and the North Rough Ridge in the SE. The valley is approximately 38 km long, 3 to 7.5 km wide and is drained by the NE flowing Pool Burn, which meets the SW flowing Ida Burn. The resulting unified stream flows into the Manuherikia river which drains the next door depression to the NW. The present work deals with the Ida Valley basin and more specifically with the geology studied within two Prospecting Licence areas held by Gold Mines of NZ Ltd on the southeastern flank of the valley.

Jan 1, 1977

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By Askew J. E

All facets of current practices of cable dowelling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited are re- viewed. This includes materials specific- ations, installation practices and design pro- cedures. Cable dowelling for cut and fill stoping, square set timber stoping, longhole open stoping and level reinforcement is considered. Installation is simple and can be mechanised to eliminate heavy lifting. Quality control is essential for optimum performance of the re- inforcement. Design patterns must consider the mining method, reinforcement economics, acceptable stability standards and mine production priorities.

Jan 1, 1977

The drilling and evaluation of bore cores provides the best available statistical basis for characterizing a coal prospect. Important, long-term decisions by management frequently must be based on the results. The majority of coal mined presently is used for steam raising or the production of metallurgical coke. Common bore core tests and analyses appropriate to this usage can be cate- gorized as non-destructive, chemical, physical, petrographic, caking/plastometric and propert- ies of non-coal material. The major tests within each category are described. Certain specific information from the bore cores is required by the coal geologist, mining engineer, coal preparation engineer and the user, either individually or as a group. The optimal bore core evaluation test pro- gramme is the one which satisfies the needs of all the professional disciplines with the grtatest speed and at minimal cost. The principal steps in such a programme are listed. There is an urgent need for a bold new Australian standard to provide the necessary guidelines to an industry which at present lacks uniformity in its approach to the task.

Jan 1, 1977

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

The problems encountered with the introduction and use of Isanol underground are described. Significant direct as well as indirect savings have resulted from the use of Isanol. Field studies have shown that the concentration of common gases released during detonation is considerably lower than with conventional nitro-compound type of explosives.

Jan 1, 1977

By Nash B. G W

In June 1976 a 600'tonne/day manganese ore sinter machine, with on-strand cooling, was commissioned at the plant of Tasmanian Electro Metallurgical Company Pty. Ltd. at Bell Bay, Tasmania. This machine was installed in order to utilize manganese lump ore screenings generated in the preparation of raw materials prior to charging to the electric smelting furnaces at Bell Bay. Since commissioning, trial sintering of a number of different grades of manganese ore fines from Groote Eylandt Mining Company Pty. Ltd, has been conducted and suitable sinter has been produced from these different grades. The sinter produced is used as part of the furnace burden in both ferro manganese production and silico manganese production. The inclusion of sinter as part of the charge in the production of ferro manganese has considerably improved furnace operating conditions and performance.

Jan 1, 1977

The fragmentation of whole rock by blasting has an influence on the subsequent loading, hauling and crushing operations. However, no method of calculating the frag- mentation has yet been developed. This paper gives a method of calculating the fragmen- tation for the simplest form of blasting, i.e. cratering. Cratering consists of the detonation of a spherical charge of explosive in a blasthole breaking to one free surface. This paper gives a method of calculating the extent of the system of radial cracks generated by the explosive in the rock. This system of radial cracks is then used to calculate the fragment size distribution curve from blasting. The calculated curves are shown to be in good agreement with experiment.

Jan 1, 1977

The T33-34 blast, the first major blast at Mount Isa Mines, broke 1,360,000 tonnes of copper ore using 349 tonnes of explosives. The original concept of firing T33, T34, T35 and U37 separately was changed during the life of the project due to adverse ground conditions. These conditions also caused the stoping method to be modified after the firing of the stopes had started. To stabilise the two stopes T33 and T34 where large fall off was occurring, rib pillars were left in the original slot. This caused the blast design to be more complex as these rib pillars had to "lead" the blast. The implication of such a large blast on the underground and surface environment was thoroughly investigated and precautions taken. The charging time of the blast was six weeks. Hook-up was started four days before the blast and continued until two hours prior to the blast. Detailed scheduling was carried out of other work that had to be done in the 24 hours before the blast to ensure that there were no delays in the firing.

Jan 1, 1977

By Mills R, Shannon W. T, Finch J

As an extension to investigations into methods of upgrading the Iitania content of ilmenite concentrate from beach sands using 100 g/day, a small pilot plant treating 23 kg/ day of ilmenite was used.In the pilot plant the iron oxide in the ilmenite was reduced to iron at 1200°C using carbon (coal/char) without melting the material, using a tunnel kiln heating cycle, the charges contained in saggars, The iron was then separated from the titania fraction by ball milling, wet magnetic separation, and screening. The resulting magnetic product was high in iron (about 80 per cent Fe) and the non-magnetic product high intitania (about 70 per cent TiO2).From this trial sufficient data were obtained to enable the preparation of a flow sheet for a plant producing 62,300 tonnes/year total products, and an estimate of costs to be made. This has shown that for an estimatedcapital expenditure of nearly $6,000,000 and annual production costs of about $4,000,000, the cost per tonne of high titania product (76 per cent TiO2) would be nearly $70.

Jan 1, 1977

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

In underground ore mining of copper ore, lead-zinc ore, tin ore and fluorspare in German Democratic Republic geological situation is characterized by ore deposits of small thickness and great variability of ore grades and mining conditions. For long range mining strategy and short-term planning of production a model was developed fitting to make optimal economic mining decisions. Starting point of the model is a cost function representing all direct costs per unit recoverable metal in concentrate for each stoping unit (ore reserve block). In the costs function the results of regression analysis of ore grade and metal recovery in concentration plant were considered. All stoping units (ore reserve blocks) of a mine were arranged to growing direct costs. The relationships of recoverable metal, ore tonnages and corresponding costs were plotted in a diagram. The data processed by- computer and the graphic representation of the results make possible 1. economic evaluation of stopes and ore reserve blocks, 2. estimation of cut off grade, 3. optimization of works planning.

Jan 1, 1977

Roasting of zinc concentrate at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited, (E.Z.), is carried out in two fluid bed roasters capable of treating 450000 tonne/yr, or sufficient for the output of 220000 tonne of salable zinc. The furnaces were constructed by Lurgi, Australia, to the basic design developed by Vieille Montagne Company of Balen, Belgium. The advantages of fluid bed roasting include a higher metallurgical efficiency in sulphur oxidation from a feed which does not require any pre-grinding, mechanical reliabil- ity through the absence of any moving parts within the furnace and the capability of being scaled up to a large unit.

Jan 1, 1977

Economic mathematical methods have been developed and applied in the design, planning, development and managing stages in the mining industry. Economic and technological efficiency is achieved with the aid of a large range of probability models, which are used to enable decisions to be made progressively during the different stages. The entire operation is considered as a total system made up of sub- systems and the models representing these are consecutively interrelated with each other. Algorithms and programmes representing the economic mathematical models for all the stages involved were tested and were found to be applicable to the various important mines in the Donetsk basin. Currently, these models are accepted and widely used.

Jan 1, 1977

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

Declining from surface provides access, haulageway, ventilation and provision for ser- vices for stoping and development. Three boom jumbos and 3.8 m3 capacity diesel loaders are used in decline development, the majority of which is driven at a gradient of 1 in 9. Primary ventilation is drawn from the mine through raisebored airways and high pressure contra rotating fans provide secondary ventil- ation. To meet schedules a special decline crew was formed on similar lines to a mining con- tractor. The basis of payment for the mining party was changed and the net effect was to accelerate development. Ground conditions demand constant support and this is achieved with chemical anchor rock bolts, multistrand grouted bolts and shotcrete. Major local shear zones are encountered and when they are to be driven through, a combina- tion of the above methods, involving a spiling technique, is used.

Jan 1, 1977

A study of drilling data at various stages of development of an orebody show that the semi-variogram, used for calculating the accuracy of block estimates can be ill-defined if too few data are available. The consequencesin this case are to have blocks supposedly more accurately known than is possible at the early drilling stage; such a result being potentially dangerous. However, as the amount of data increases the recalculated, semi-variograms approach the underlying semi-variogram of the deposit and the calculations made using them become more reliable and robust.

Jan 1, 1977