Search Documents

Structural analyses of oriented bore core sections from the West Wallsend No.2 Colliery Holding together with investigations in adjac- ent collieries and on the surface delineated structural phenomena. The rocks examined are anisotropic due to strongly developed bedding planes and the presence of penetrative joint planes. Joints, in this context, are regarded as mechanical discontinuities, they are genetically identif- ied wherever possible and their spatial attit- udes are determined and geometrically related to the regional structure. Identifiable anisotropies in the roof- and floor-strata of the Borehole Seam render favour- able mining directions for longwall and bord and pillar layouts.

Jan 1, 1972

The stratigraphy of the Singleton Coal Measures is reviewed and a revised stratigrapixy which has been ratified by the N.S.W. Standing Committee for Coalfield geology is nominated and defined by a selected type section. Withir the type section the occurrence of repetitive phases are illustrated and described. Coal. Measure units within the Singleton Coal Mean sures, termed the Wollombi and Wittingham Coal Measures respectively, are correlated with the Newcastle and Tomago Coal Measures. In formal nomenclature the Singleton Coal Measures are designated the Singleton Super Group. The major depositional cycles within the Coal Mea- sures are outlined together with those lesser phases within the Coal bearing sequences that influence the mining conditions likely to be encountered. Both tectonic and sedimentary features of the Singleton Coal Measures are considered and the localized post depositional effects on the coal seams and roof strata in- duced by differential, compactions are emphar Sized.

Jan 1, 1972

Exploration work at the southern flank of the Mt. Coffin diapir has encountered three different types of copper ores: copper carbonate, largely malachite; secondary sulphides, mainly chalcocite replacing pyrite; and a primary arsenopyrite-tennantite-tetrahedrite-chalcopyrite association. The secondary copper ore is occasionally stratiform but mainly erratic at the contact between tillites and siltstones of the Tapley Hill formation.There have been two stages of primary mineralization.1. Arsenopyrite, tennantite, and tetrahedrite occur in siderite veins.2. Revival of the diapirism has caused fracturing and local brecciation of the rimrock and subsequently ascending solutions precipitated chalcopyrite. The chalcopyrite also partly replaced arsenopyrite, tennantite, and tetrahedrite.

Jan 1, 1972

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

The Electricity Commission of New South Wales operates three power stations located on Lake Macquarie and Lake Munmorah. Coal for these power stations is supplied by three collieries operated by the Electricity Commission, three operated by the State Mines Control Authorityrand one privately owned. Most of the coal used in these power stations is won from the Great Northern seam which lies at depths of up to 220 ft at Awaba and at depths of the order of 600 ft at the remaining mines on the southern end of the field.

Jan 1, 1972

Byproduct coking is practised in three of the major Australian ironmaking centres, the Newcastle and Whyalla works of the Broken Hill Proprietary Co. Ltd. and the Port Kembla works of Australian Iron & Steel Pty. Ltd. Coking first commenced at Newcastle in 1915 and at Port Kembla in 1938. The installations established at these centres include coal cleaning facilities and com- plete byproduct streams. The Whyalla plant, because of its location is somewhat less extensive, having no coal cleaning plant and a comparatively restricted byproduct section. As new batteries have been built every opportunity has been taken to incorporate modern design features and improved operat- ing techniques. This has included the provision of equipment to reduce atmospheric and water pollution. A marked reduction of markets for byproducts has had serious repercussions on the profitability of this section of the Industry.

Jan 1, 1972

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

In making any attempts to determine the depositional environments in which coal seams accumulated it would be useful to establish whether there is a pattern, or patterns, of development which the majority of the seams have followed. To this end, the distribution of types of coal seam sequences found in the standard petrographic profiles of about a hundred Australian coal seams of Permian and Triassic age has been examined statistically, using the "chi square test" with the limiting probability set at O·Gl.Results indicate that non-random conditions have probably prevailed during the deposition of most of the seams. More samples are needed for conclusive results.The plants, or some other internal feature of the swamp environment, have been the important controlling factor in the development of the seam sequences.Comparison has been made with some British Carboniferous coals.

Jan 1, 1972

A description is given of preliminary work done to identify the problems inherent in electrochemical oxidation of metal sulphides, and particularly in the use of powder compacts as anodes in electrolysis. Lead flotation concentrate pressed into a compact can serve as an anode for direct electrowinning of lead according to the reaction PbS -7 Pb2+ +So +2e. No pYrometallurgical step is required, and sulphur is recovered in elemental form.In the experimental work, electrical conductivity of the compacts was achieved by addition of 5·5 per cent of graphite. After compaction at 10-20 tons/sq. in. the anodes were strong and remained intact throughout the electro-oxidation period. Perchlorate electrolyte was used, but fluosilicate electrolyte is also applicable. A sheet of pure lead formed the starting cathode.As anode potential increased above 1·0 V (v. SHE) PbS04 was formed in increasing amount. At 0·90 V, Pb2+ extraction efficiency was 85 per cent. Anode potential was kept low by electrolysing at 60°C and 15 mA/sq. cm., and by improving the porosity of the compact. Other metal sulphides (Zn, Fe, Cu) in the flotation concentrate also oxidize and release metal ions to the electrolyte, which would need to be purified prior to deposition of lead.Power requirement in a laboratory cell was about 0·24 kWh per lb of lead extracted.

Jan 1, 1972

By W. J. LANGRON

This paper describes the results of VLF-EM test surveys, using the Ronka EM-16 equipment, over a selection of environments in Australia and Papua.Using comparisons with known geology, drilling information and other geophysical work it is shown that the maximum depth of penetration of the method is about 100 ft but is considerably less than this in most areas.The author believes the method could aid in geological mapping and provide a useful adjunct to aeromagnetic surveying in some areas.

Jan 1, 1972

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By R WOODS

The interaction of, flotation collectors with sulphide mmerals takes place at the solid-solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulphides is an electrochemical process, xanthates being electro-oxidized to chemisorbed xanthate and dixanthogen.The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidized xanthate species. The action of reagents which can activate or depress the flotation of sulphides is discussed briefly.

Jan 1, 1972

This paper gives the background to the development of solvent extraction processes for the recovery of metals from aqueous solutions. Its growing importance in Australia for the recovery of both uranium and copper is dis- cussed, as well as the developments in mixer-settler design as applied to recent plants. The economic significance of solvent extraction as an alterna- tive to cementation is discussed and important features of each process are highlighted by comparison of costs for each process in a hypothetical situa- Tion.

Jan 1, 1971

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

The ore deposits investigated are composed primarily of hcmatite and can be grouped into three categories depending on the amount of leaching of silica and carbonate which has occurred from the original iron formation, and on the amount of recrystallization of the hematite. Minor constituents are magnetite. goethite, and quartz.Texturally. there are five different types of hematite, formed at different stages during the genesis of the ores.These are1. anhedral hematite grains formed by recrystallization of hematite already present in the original iron formation.2. hematite formed by martitization of euhedral magnetite, 3. massive aggregates of fine- to medium-grain hematite formed by recrystallization of (l) and (2).4. tabular or prismatic hematite grains occurring around the boundaries of the massive aggregates or martite euhedra. and in fractures and5. specular hematite. which is present in fractures in ore types (l) to (4).Minor and trace-element analyses, determined using an electron-probe microanalyser. indicated that only silica (less than 0·01 per cent) and cobalt (less than 0·002 per cent) were present in the magnetite and hematite from unaltered iron formation and in the hematite from the ores. Low concentrations of trace elements are typical of magnetite in ores formed as marine precipitates. On the basis of the analyses alone. it proved impossible to distinguish between the five hematite types. A determination of the variation in rare-earth trace element contents between iron oxides in the iron formation and iron oxides in the ores indicates that the rare earths were depleted during ore formation. A possible explanation is that they were removed in solution with silica as it was leached from the iron formation.

Jan 1, 1971

The occurrence is recorded of an indurated kaolinite claystone associated with red-beds in the Burralow Formation of the Narrabeen Group near Putty toward the north-west of the Sydney Basin. The claystone is similar in composition and structure to the Garie Member which immediately overlies the kaolinite-rich "chocolate shales" of the Bald Hill Claystone in the sofrthern part of the basin. Unlike the Garie Member however, the Putty claystone is lenticular and the associated red-beds contain abundant quartz and illite in addition to kaolinite.The source of the Putty claystone is not known. Possibly it is an extension of the Garie Member to the northwest or alternatively, it may represent fine outwash of detritus that produced the coarse-grained kaolinite claystones in the Triassic succession of the Merrygoen-Binnaway area. Although the material is suitable for the manufacture of aluminous refractories the limited size of the deposit precludes its commercial exploitation.

Jan 1, 1971

By Stump NW

Until a year ago all isotope on-stream analysis utilised flow cells similar to those designed for conventional X-ray on-stream analysis. These systems incorporated a fairly complex sampling system necessary to present a representa- tive air-free sample of the main process to the flow cell. Maintenance costs and capital costs associated with flow cells and sampling systems have been generally high. Costs can be greatly reduced and reliability greatly increased, by using isotopes incorporated in immersible on-stream analysis probes which actually dip into the main process stream eliminating the need for sampling. A bonus of other advantages associated with immersible probes includes temperature stability and ease of calibration. This paper discusses details and results of the probe systems, justifica- tion for installing on-stream analysis, comparison of conventional X-ray and isotope techniques, and a brief survey of methods of analysis using radio- isotopes in on-stream elemental determinations.

Jan 1, 1971

During mapping in the Bijerkerno area (Fig. 1), well-preserved sedimentary structures were found at three separate localities. The structures are of four varieties, which are 1. small-scale cross-bedding (Fig. 2),2. convolute bedding (Fig. 3),3. minor scour and fill (Fig. 4), and4. flame structures.Ripple-marking is also doubtfully present.These structures are best preserved in what was...

Jan 1, 1971