Search Documents

By E S. Bernard

Toughness testing of fibre reinforced concrete (FRC) at 28 days age is typically undertaken as part of quality control for the many applications where fibres are used in concrete, including shotcrete, tunnel segments, and cast-in-place tunnel linings. The performance achieved at 28 days is usually assumed to be retained with increasing age. However, as the average strength grade of concrete used in most tunnelling applications, including tunnel segments, has steadily increased over the last 20 years, this assumption is becoming increasingly unviable. This is because for some types of fibre the mode of post-crack fibre behaviour depends on the strength of the concrete and can change from a desirable high-energy pull-out mode to a low-energy rupture mode as the strength and age of concrete increases. This paper describes a series of trials performed over two years in which the American Society for Testing and Materials (ASTM) C1609/C1609M beam tests were used to assess the performance of FRC reinforced with two widely used brands of steel and macro-synthetic fibre. The hooked-end steel fibres used for half the beams exhibited a dramatic fall in performance beyond 56 days age as the mode of failure changed from pull-out to rupture. The other fibre did not exhibit a fall in performance with age. This phenomenon highlights the need to quantify performance of FRC at much later ages when long-term performance is required, for example, to resist seismic events or changes in ground stress due to nearby excavations. As an alternative, a reduction factor may be applied to the performance of FRC mixes for which evidence of satisfactory long-term performance is not?available.CITATION:Bernard, E S, 2014. Age-dependent changes in post-cracking performance of fibre-reinforced concrete for tunnel?segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Pisolitic iron ores (also known as channel iron deposits) are an important resource of medium-grade iron ore in the Hamersley Province of Western Australia. They are a special case of transported pisolitic ferricrust, differing from normal transported ferricrust only in the exceptionally high iron and low alumina content. The pisoids typically range up to 5 mm in diameter with abundant particles of ferruginised fossil wood up to 15 mm in maximum diameter preserved in the sediment. Field observations indicate that pisoliths are commonly initiated by the action of raindrops on iron-rich soil. Pisolites form by the impact of raindrops forming coated beads of ferruginous soil, which after dehydration obtain additional coatings during successive showers. Thick deposits of pisolite that are transported and deposited primarily by sheetwash form in the distal regions of the pediment. A size range limited to particles that may be transported by extremely shallow water characterises the abundant fossil wood fragments. The absence of fine sedimentary layering in pisolitic iron ores is explained by the action of soil-forming processes after deposition, while the major coarse bedding features derive from successive erosional and depositional events in the evolution of the pediment. They are not deposited in channels by rivers which, in arid to semi-arid conditions, typically deposit quartz sands and gravels with characteristic point bars and current bedding, abundant ferruginous granules, but rarely pisoids. However, they may fill abandoned river channels.

Jan 1, 2007

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Hammond J. R, Ward T. A

The Tom Price orebody, in the Hamersley Ranges of North West of Western Australia, is mined by Hamersley Iron Pty. Limited. The orebody is a folded sequence of hematite and shale bands capped with goethite, with a con- sequential variable iron content. The overall grade is below that required to yield spec- ification product, necessitating selective mining, 'Zone Plans' based on geological structure have been developed to yield forward information on material types and grades. Short and medium term mine plans - the initial stage of quality control - are based upon these 'zone plans'. Blasts are laid out to break to the grade boundaries, thus minimising dilution, and the samples taken from the blasthole cuttings provide blast grades. Blending of shovel out- put from different blasts forms the operational basis of grade control. Shales, being more friable than hematite, produce fines that are lower in iron grade than lump. Quality control in the mine centres around maintaining the target fines grade, compensation being applied in the mine if the fines grade lies outside the target range.

Jan 1, 1973

Investigation of the Effect of N-Substituents on Performance of Thioureas as Special Collectors for Copper Sulfides by ab Initio Calculations

Sep 13, 2010

Iron Ore - Mineral Processing Overview Several years of iron ore price increases, coupled with a period of strong global demand for raw materials, presented iron and steel producers with unprecedented costs and difficulty procuring the demanded high quantities of iron ore. These conditions spurred many companies to investigate new ore bodies and also reassess past decisions (such as divestment of captive iron ore mines that ensured dedicated supply or a move to reliance on the 'spot market' instead of long term contracts with suppliers) and revisit alternative sources of iron units, including low grade deposits, tailings reprocessing, Ti-rich ores, and iron sands. To properly upgrade these iron sources requires a complete battery of mineral processing techniques. Within different regions around the world, operations and technology have developed to specifically beneficiate the local ore bodies. This paper attempts to bring these different general processing techniques together to allow insight into various common and proven methods of iron ore beneficiation. This paper further explores the current trend to develop global iron ore reserves, and discusses the methods to beneficiate and successfully reduce and smelt iron ore using Outotec's physical separation, direct reduction and smelting technologies for final production of pig iron and slag. Use of these various technologies may allow treatment of what was typically considered a tailings stream into a profitable product.

Sep 13, 2010

By P Dowd, R Jeuken, C Xu

In Australian coalmines there are a number of coal quality parameters that are measured by analysing samples from boreholes. The data points are used to generate spatial models of these parameters, typically using inverse distance as an interpolation method. Numerous additional boreholes are drilled which have geophysical logs measured downhole but from which no coal quality samples are taken. Full suites of coal quality analyses are expensive and time consuming to drill and sample. If geophysical proxies for coal quality could be used, this would greatly improve the accuracy of the resource estimation without additional cost.This paper examines two of the most important coal quality parameters – ash and volatile matter – and assesses the results of a number of geostatistical interpolation methods. The aim is to improve the accuracy of the interpolated models. Auxiliary variables from geophysical logs are also trialled to improve the estimation.A multivariate analysis of ash, volatile matter and several auxiliary variables of a selected coal seam was undertaken in a spatial context, using variography. This was used to construct a model of co-regionalisation that relates all of the variables as manifestations of an underlying geological theme.The traditional inverse distance interpolation approach was compared to ordinary kriging, universal kriging, co-kriging, regression kriging and kriging with external drift approaches. The relative merits of the six interpolation methods were compared by removing all points, one at a time and estimating at the thus known location. The mean error and the root mean square error were evaluated as a measure of bias and precision.This paper demonstrates that there is significant opportunity to improve the estimations of coal quality when using kriging with external drift. For example, the results show that when using the depth of a sample as an external drift variable there is a significant improvement in the accuracy of estimation for volatile matter. Furthermore, when using borehole wireline density logs as an auxiliary variable for ash content, there is improvement in the estimation of the in situ ash. The underpinning reasons for this are discussed in the context of the underlying geology and the physical properties of the coal. These findings hold promise for utilising cheaper proxies for coal quality parameters to dramatically improve data density and the quality of estimations.CITATION:Jeuken, R, Xu, C and Dowd, P, 2017. Improving coal quality estimations using geostatistics and auxiliary variables, in Proceedings Tenth International Mining Geology Conference 2017, pp 157–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Brenchley R

Partitioning behaviour studies for -particles in the 250 to 1,000 micron size range at. the Curragh coal preparation plant are presented. Plant surveys were conducted to compare the partitioning efficiencies of dense medium cyclones and froth flotation. The aim was to assess the potential for improving yield of coal by directing more of the top size of flotation feed material to dense medium cyclones. ovel mass balancing and model fitting NI procedures were used. While flotation offers high yield of low ash particles smaller than 500 microns, dense medium cyclone rejection .of high ash particles larger than 250 microns is superior. These strengths of the two processes are turned to good advantage by the use or desliming sieve bends which tend to perform some density separation on the'size fractions of interest, directing lower ash material to froth flotation than to the dense medium cyclones.

Jan 1, 1987

Ensuring the success of a major resource development project, whether in the Gippsland Basin or elsewhere, is typically both a complex and costly process. It is therefore imperative from the point of view of the proponents of such a project - and in particular the financiers - that everything possible be done to minimise administrative confusion and delay in the establishment phase of the project, and to put systems in place which enable the project to run smoothly and efficiently in the later stages of its development and operation. An essential element in this process is ensuring that the project management is able to come to terms with and deal effectively with the relevant planning and environmental laws.

Jan 1, 1992

By M Ziemski

The provision and management of energy in both fuel and electricity forms is an increasingly important consideration for mines. Pressures from communities, governments and markets are increasing towards more transparent and improved energy management. Combined with the energy-water nexus, where water and energy are closely related in the operation of a mine, this emerging business climate means a more thorough and responsible approach is required for the acquisition and use of energy, as well as the release of emissions. Many of the complexities in potential new ore bodies are borne in remote locations, high altitudes, low grades, arid climates and deep deposits. Each of these challenges affects the successful provision of energy. In combination, such challenges can leave an operation seemingly unviable from an energy perspective, especially when approached from a traditional mining energy feasibility lens. This paper discusses some of the energy alternatives currently available and emerging in the mining industry. Both energy supply and demand options are considered, which can provide a very different energy footprint with the flexibility to address, and potentially overcome, major energy challenges for a mine. CITATION: Ziemski, M, 2018. Energy complexities in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 106–111 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Detailed petrographic analyses of coal seams from the Newcastle, Illawarra, and Lithgow Coal Measures were made for a number of localities for each of twelve seams. From these analyses characteristic standardprofiles were derived for each seam. Two broad types of profile were found; one in which vitrite-poor and vitrite-rich layers alternate, and another in which there is a steady decrease in vitrite from the base to the top of the seam. From comparison of the petrographic profiles it was concluded that the Great Northern Seam in the Northern Coalfield is a possible equivalent to the BulIi in the Southern; and likewise the Fassifern to the Balgowni...

Jan 1, 1967

In this paper is given a description of the flotation plant recently erected by Broken Hill South Limited at the South Mine, Broken Hill, N.S.W. It has been built on the site of the old flotation plant, which was described in a previous paper published by the author. The present paper is supplementary to the former paper in that it replaced the following sections thereof, namely, those from end of the second paragraph, page 269, to the end of the first paragraph page 282, and from the end of the second paragraph, page 284, to the end of the third paragraph, page 302.The roll crushing, fine grinding, gravity concentration, filtration, disposal of products and sampling in the new plant are the same as described in the above mentioned paper.The reconstruction of the flotation section, described herein, completes the reconstruction and modernisation of the treatment plant which was begun in 1928. A description of these earlier alterations has already been published in the Proceedings of this Institute.

Jan 1, 1935

By Enever JR

In-situ rock stress measurements conducted in the Phillipines and on Bougainville have revealed stress fields significantly different from expectations based on intraplate experience. The results have potential significance in regard to both engineering practice in the Pacific Rim region as well as in helping to understand the geological processes occuring near subduction Zones.

Jan 1, 1987

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008

This paper explores options worthy of consideration in the management of S02 produced from the gold roasting operations at Kalgoorlie. Some of the options have relevance to other sources of SO2 in the region, eminating from nickel smelting operations. The paper considers the following options: 1. Capture of SO2 within the roaster where sulphur-containing reaction products are mixed with the calcine. 2. Processes in which the sulphur-containing products are bled separately from the stack for further treatment or for dumping as a waste. These include: Seawater-based scrubbing of SO2; Sulphuric acid manufacture as a feedstock for fertiliser production or for leaching of bauxite; its use as Caro's acid: and the production of value-added sulphur-containing reagents eg liquid S02 and sulphonic acid.

Jan 1, 1992

By L W. Palmer

"Evaluating the geological risk associated with ore deposits is becoming common practice in the mining industry. While geostatistical simulation is a useful tool for evaluating this risk, the effect of applying different types of simulation is less understood. For simulation of categorical variables like rock types, available methods perform simulation in fundamentally different ways. In this study, the geological risk relevant for informed mine planning is studied with two categorical simulation methods, PluriGaussian Simulation (PGS) and Sequential Indicator Simulation (SIS). Risk is expressed as a probability of repeated occurrence of lithological units in the same location across simulations. Significant differences are observed between the methods in terms of spatial distribution of risk. To identify the most plausible risk model, the input parameters at every step of both techniques are scrutinised. PGS and SIS inputs are classified as four parameters that are: fundamental to implementation of the methodfixed to enable comparison of PGS and SISdetermined by user interpretation, hence variablenormally optimised during application of PGS and SIS. The effect of parameter selection from categories 1 and 4 on the risk model is investigated using drill core data from a leucogranite deposit. A corresponding block model is created for assigning outputs from PGS and SIS. Risk models produced by either method are illustrated in a cut-out from the block model to enable bench-by-bench comparison. For PGS, risk associated with relatively rare lithologies is relatively sensitive to variation of parameters. Independent of the abundance of lithology, a location-dependent effect of variogram and vertical proportion curve parameter selection is observed, with risk increasing towards the deposit edge. Although SIS requires fewer inputs, single lithologies must be modelled in turn. Using small numbers of samples in the search neighbourhood, all risk models differ substantially. For larger numbers of samples, the risk models are similar. Overall it appears that the risk model produced using SIS is less sensitive to changes than PGS but further work is required to confirm this.CITATION:Palmer, L W and Glass, H J, 2014. Risk associated with rock type prediction using simulation techniques, in Proceedings Ninth International Mining Geology Conference 2014 , pp 217–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

An efficient stores organisation is essential for an efficient undertaking. Unless the stores organisation is able to meet the requirements of its requisitioners promptly and economically, the undertaking as a whole cannot function efficiently.Delays or errors in supply of material, or substitution due to lack of material availability from the stores are costly and must be eliminated. This then makes the objective of a store, to supply on demand at the cheapest possible price, those items of stock which it is organised to carry, also to procure as quickly as possible and at the lowest price those special items required which are not normally carried in stock. To do this it is necessary to set up a stores organisation consistent with the size and requirements of the undertaking. Stores organisations vary with the nature of the undertaking they are designed to serve. In the case of the Broken Hill Associated Smelters Pty. Ltd., an organisation has been established to meet the operating and maintenance requirements of the Port Pirie Works. These embrace the particularly wide range 0:1; activities associated with roasting" blast furnacing and refining the lead concentrates from the Broken Hill Mines in a continuous metallurgical process producing a variety of refined metals; also many associated activities including power production and engineering maintenance and construction.

Jan 1, 1951

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

Small scale' table concentration tests have many critics. Many metallurgists consider that such tests are of problematical value because of the difficulties involved in conducting and interpreting them.Many kinds of small-scale ore dressing tests are difficult to conduct, and there is, perhaps, good reason for thinking that table concentration tests are amongst the most difficuIt.Interpretation of results from small-scale tests is the responsibility of the metallurgists and engineers in charge, and it is often held that small-scale table concentration tests are particularly difficmlt to interpret.TESTING FOR TABLE CONCENTRATIONOn analysis it appears that the difficulties encountered in conducting small-scale table concentration tests are of three fairly distinct kinds. Firstly, there are difficulties due inherently to the smallscale nature of the operations; for example the smaller width of all mineral bands on the table and the less complete separation due to the shorter length of travel between the feed and discharge points.Secondly, there are the effects of batch operation owing to the fact that the mineral particles behave differently during the initial period when the sample is just beginning to spread over the table, the middle period when feed and discharge are even and continuous, and the final stage, when the last of the sample has been added and the table is beginning to empty itself.

Jan 1, 1954