Search Documents

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

By I Testrow, M Wiggin

Scrutiny of the whole explosives industry has increased as a result of the terrorist attacks on the World Trade Centre and the Pentagon on 11 September 2001 and the bombings in Indonesia, including the Bali bombings last year. This has been highlighted in specific press releases from governing bodies, like the Department of Mineral and Petroleum Resources û Western Australia, on the necessity of being in compliance with regulations for storage of explosives. As a result, audits by inspectors to assess compliance are to be expected. In a proactive move, DynoConsult has assisted several customers through benchmarking current practices, in order to identify any areas of non-compliance to the statutory requirements for explosive storage and security. This paper discusses the outcomes of supplier discussions and customer audits and highlights the implications for the industry.

Jan 1, 2003

For effective backfilling, a system with the 13 features covered under the section: effective backfill systems, is required. Effective backfilling cannot be done with systems that are badly designed, outdated or overextended. But in cases where the requirements for effective backfilling are overlooked, the shortcomings of such systems may wrongly come to be regarded as limitations to the capabilities of backfilling per se. Mining is currently done to depths of 3500 m, and is to go deeper since the gold-bearing reef extends down to 4000 m and 5000 m below surface. Effective backfilling systems will be required at such depths, and with suitable design this can be achieved. Mining the narrow tabular orebody of a typical South African gold mine is described at the start of this paper, then cycloned backfilling is discussed in general, and its effectiveness (most of the fill placed in South Africa is cycloned backfill or ædeslimed tailingsÆ).

Jan 1, 1998

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

A geologic, petrographic and geochemical study has been performed on the pyroclastic flow deposits in the coastal area of East Zhejiang Province, Southeast China. This study leads to classification of the pyroclastic flow deposits into three associations: the extrusive type, the surge type and the ash flow type welded tuff associations. Through detailed investigation and comparison of the characteristics of these lithologic associations, with emphasis on the welded tuffs, a comprehensive model has been proposed to demonstrate the petrogenesis of the pyroclastic flow deposits.

Jan 1, 1995

The need to describe shape properties of solid particles arises in many applications in the mining and minerals industry. This paper presents a technique for describing the shape of 2D particle profiles from digital images, based on traversals of the circumference of the profile boundary at a succession of different scales. The traversals are undertaken in such a way as to establish a more stable set of results than usually arises from conventional fractal multi-scale shape characterisation techniques. The resulting values can be used to provide compact information on various generic shape features of the particle profile.

Jan 1, 1998

The geologists at the Zinc Mine in Broken Hill have developed a method of logging core using portable MS-DOS computers and LOTUS 123. The computer based logging system has almost halved both the time and cost to produce a completed log. The system is fast, flexible, easy and pleasant to use.

Jan 1, 1990

A static equilibrium mathematical model of the lead,flotation circuit at The Zinc Corporation Limited is developed to permit the feasibility of applying computer control techniques to be studied. The model is based on the relationship between the cumulative recovery of a mineral species R from n flotation cells or assemblies in a unit given asR = M(1-(1 - p)?)where M is the maximum possible: recovery and p is the probability of flotation for the particular mineral.The verification of this relationship by data from pilot plant cell-to-cell and plant open flow flotation units shows that these systems behave as if the probability p is constant for each cell or assembly of anyone unit. It is also concluded from this study that mineral recovery is independent of the head assay. Two consequences of this probability relationship, are demonstrated.1. The total recovery from an open flow unit is enhanced by increasing the number of flotation assemblies but maintaining a constant flotation time and total air addition.2. The rougher and scavenger capacity required to recover a bulk lead-zinc concentrate is approximately half that used for selective flotation.The static equilibrium model is derived by solving a series, of mass balance equations which incorporate the recovery-probability relationship for each type of flotation unit. It is used to calculate the complete metallurgy of the circuit for any arrangement of cells knowing only the plant feed assays and the probabilities of flotation for the three mineral types, galena, marmatite, and gangue for rougher, scavenger, and cleaner flotation. The high degree of prediction obtained is demonstrated by comparison with plant results.Pulp flowrate is the principal variable affecting the accuracy of the present model. Work is in progress to establish this effect and permit the derivation of a dynamic model. Even so, the static model is valuable in its present form for the analysis and design of circuits, and optimisation studies using computer services have been conducted.

Jan 1, 1964

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

Every estimate of ore reserves necessarily contains an assumption in regard to the specific gravity of the ore. This assumed figure may be based on experimental data, on textbook data, or on a reconciliation of past tonnage estimates and production figures. Not infrequently it is simply a guess - shrewd or otherwise.Errors in the density factor are not likely to be serious in gold-quartz mines-or, at least, not so serious as in base metal mines. It is to the closer determination of ore density in the latter that this paper is devoted. Moreover, the remarks apply to ores which show no appreciable pore space.Not many ore bodies are sufficiently homogeneous to allow of a truly representative factor being obtained by the simple testing of a few specimens of ore, or by the weighing, after breaking, of a carefully measured block. The empirical figure derived from a comparison of past ore reserves and actual production can never truly describe conditions other than those now past; no real link with ore as yet unmined is provided. The dilution of heavy ore by waste is not exposed by this method, but is effectively cloaked. Anyerrors in past estimations of ore reserves are transmitted, by way of the density factor, as a source of error in all future estimates.ObjectIons may be raised to the practice of weighing measured blocks of ore in the case of any but a very homogeneous ore body. Even then, the exact composition of the block weighed, and an indication of whether its moisture content is representative of the whole, are difficult to determine.

Jan 1, 1940

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J V. Lawless

Two types of low sulphidation epithermal deposits that have different gangue mineralogies and ore shoot geometries are recognised. One has laterally near-continuous ore shoots over a significant vertical interval that consist of quartz, chalcedony, pyrite, minor base metal sulphides and adularia, with electrum. The other type of deposit has discrete near-vertical ore shoots of a lesser vertical extent, that consist of quartz, pyrite, base metal sulphides, sulphosalts, electrum and in their upper parts barite, which are enclosed in veins of earlier quartz. The gold mineralisation in both deposit types is considered to be a co-precipitate of pyrite, with that in the first type of deposit produced by prolonged boiling in an upflow of a hydrothermal system (Upflow Deposits); an example is Waihi in New Zealand. The other type is produced by mixing, a deep water primed for gold deposition by prior limited boiling, with an iron-bearing oxidised condensate of the steam released by the boiling, in an outflow of a hydrothermal system (Outflow Deposits); an example is Thames in New Zealand. Early recognition of these different types of deposits can be used to develop mineralisation models of predictive value on which to focus exploration drilling. Early recognition of an Upflow Deposit promotes an extensive program to delineate the extension of the main ore shoot. In contrast recognition of an Outflow Deposit requires a more intensive approach to find individual ore shoots which, although smaller than those found in Upflow Deposits, may be high-grade, particularly if there is earlier mineralisation present to act as a protore.

Jan 1, 1999

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

By Y Wu, F-J Ping

Today, coal production accounts for about 65 per cent of the nationÆs gross energy in China. By the year 2010, the output of coal is planned to increase to 1.65 billion tonnes and by the year 2020 to 1.9 - 2.0 billion tonnes. To meet these energy needs the Chinese coal industry is developing underground coal production on a massive scale. The new drive introduced by using direct torque control (DTC) is now proven technology for mine shaft hoisting. The drive offers unequalled speed and torque control performance as well as a low impact on the supply network by controlling the power factor to unity with a minimum of harmonics distortion.

Jan 1, 2005

By H. J. Glass, A J. Cornah

Improving the quality of the variogram helps to improve subsequent estimation and simulation processes. Two strategies for conditioning data prior to construction of the variogram are investigated using data from the Luce iron ore deposit in Canada. One strategy is the classic approach in which the deposit is subdivided into a set of structural domains. The domains are analysed individually and datapairs are recombined to produce a variogram. The second strategy is reconstruction of the deposit at an earlier stage of its history through unfolding. This involves transformation of the Cartesian coordinates into stratigraphic coordinate system. Improvement in the variogram quality, expressed in a decreased weighted deviation from a fitted model, is observed for both types of data conditioning. This indicates that, for the Luce deposit, application of data conditioning could also help to inform the selection of sampling locations.

Jan 1, 2006

Prior to the merger of BHP and Billiton, both companies had a keenfocus on improving their performance in health, safety, environment and community (HSEC) matters. This shared intent, albeit executed insomewhat different ways, provided an excellent foundation for the newCompany. During the integration planning phase, a team was formed toconsider the organisational design for consistently achieving world class HSEC performance. The design included the policy platform, resources, structures, standards and procedures to be implemented in the merged entity. A key aspect of the design was the fully integrated HSECManagement Standards. These Standards create the framework for theconsistent application of BHP BillitonÆs HSEC Policy at all of ourmanaged operations across the world. The Standards have their origin in similar frameworks adopted by BHP during the 1990s, as well as thewell-known quality related standards (eg ISO 14001). However, they areunique in that they combine all aspects of HSEC management into asingle integrated set of auditable standards. By combining these areas and integrating our HSEC Management Standards with other aspects of the æBHP Billiton WayÆ, we are establishing a holistic, line management driven improvement approach. Over time, the BHP Billiton Way will embed a systematic improvement philosophy that we expect will become a key source of competitive advantage. The HSEC Management Standards are consistent with ISO 14001,OHSAS 18001, the Australian Minerals Industry Code for EnvironmentalManagement and generally aligned with SA8000. While compliance withthese external standards ensures that a systematic approach andimprovement plans are in place, BHP BillitonÆs HSEC Standards gofurther to include minimum performance requirements that reflect theintent of our HSEC Policy. Therefore, implementation at site levelensures that robust systems are in place to implement our Policy and that accreditation can be achieved to external standards if required.To assess implementation of the HSEC Management Standards anaudit system has been designed which incorporates both self-assessmentand peer review. Each site is required to undertake an annualself-assessment of compliance with the Standards using a commonassessment protocol. Every three years a peer review is conducted at each site to confirm the results of self-assessment and to provide a means of sharing knowledge throughout the Company. The review teams are composed of line managers and HSEC professionals from around theCompany, representatives of our joint venture partners and independentspecialists as required. The Company has committed to public reportingof the audit results through our annual HSEC report and this is reflected in our published targets. From a wider perspective, as we in the resources industry strive tocollectively raise our HSEC performance and reputation, there may be arole for industry based HSEC Management Standards complemented bya level of independent review.

Jan 1, 2002

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By K Williams, T Donohue, W Chen, T Roessler, A Katterfeld

Wet sticky iron ore poses particular difficulties in every aspect of the material handling process. Material hang-ups in bins, pipes and chutes; carry-back and spillage due to insufficient belt cleaning; clogging of screens; malfunctioning of crushers as well as rat holing of gravity reclaimed stockpiles are all predominantly due to the inherent cohesion and adhesion characteristics of the wet, sticky ore (Roberts, 1993). Limited understanding and quantitative measures on the stickiness of such a material significantly lower the mining operation efficiency.This research aims to investigate the cohesion and adhesion characteristics of the wet, sticky ore on physical modelling, experimental techniques and numerical implementation. Initially, the suitable bridging mechanism that contributes to the cohesive and adhesive forces within the iron ore material was identified (Hering, Martin and Stohrer, 1989; Rumpf, 1958). A cohesion/adhesion energy density factor based contact model was then introduced to describe the stickiness of the material. Secondly, an experimental system was proposed to directly test the stickiness of the material. Such a system is able to obtain both the cohesive/adhesive shear force and tensile force of the material at a specific moisture content. Lastly, the implementation of the proposed cohesion/adhesion model into the discrete element modelling (DEM) software was also discussed. A cohesion/adhesion calibration for modelling wet sticky iron ore in DEM was then conducted to ensure the material modelled in the simulation is reflective of the reality.From the study, understanding of the cohesion/adhesion characteristics of the wet iron ore material is significantly enhanced. Experimental and numerical outcomes can be directly applied for better designing or optimising the material handling processes that involve wet sticky iron ore. Consequently, the mining operating costs can be greatly reduced.CITATION:Chen, W, Donohue, T, Williams, K, Katterfeld, A and Roessler, T, 2015. Modelling cohesion and adhesion of wet, sticky iron ores in discrete element modelling for material handling processes, in Proceedings Iron Ore 2015, pp 387–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016