Search Documents

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

By Large RR

Precious metals in the Rosebery north-end orebody occur predominantly in sphalerite- galena-pyrite ore and to a lesser extent in massive barite mineralisation. Gold may also occur in the upper parts of pyrite-chalcopyrite ore (although this ore type is usually gold poor), in pyritic mineralisation lateral to base metal sulphide lenses and in the footwall (very patchy). Although present, remobilised precious metals do not occur in economically significant quantities. Mineralogically, silver occurs dominantly in tetrahedrite and, to a lesser extent, argen- tiferous galena. Gold occurs as electrum associated dominantly with pyrite and, to a lesser extent, tetrahedrite. Geochemical modelling suggests that silver was probably transported as a chlorocomplex, while gold was transported dominantly as a thiocomplex, although at high temperature gold was transported as a chlorocomplex.

Jan 1, 1987

By T E. Jeffries, M Zentilli, J STguel, C C. Wilkinson, B G. Rusk, V H. Vry

Laser ablation Inductively Coupled Plasma Mass Spectrometry (ICPMS) analysis of fluid inclusions trapping mineralising solutions in major porphyry-copper deposits indicates that copper concentrations can reach 103 - 104 ppm in both dilute, CO2-bearing fluids and in high salinity brines. Non-Cl transport of Cu is implicated. Au has been determined at 0.2 - 0.4 ppm in the low salinity fluids and may be co-transported with Cu. In contrast, high concentrations of Fe, Mn, Zn and Pb are only attained in brines and correlate strongly with Cl-indicating chloride transport. Physical and/or temporal separation of these fluid types can therefore producemetal fractionation within porphyry systems. Evidence concerning the behaviour of Mo is less clear but brine transport appears to be favoured; phase separation is one mechanism that may account for the fractionation of Mo from Cu and the formation of quartz-molybdenite veins. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By S Moradi

The thickener overflow of zinc concentrate, obtained from flotation process in the Angouran plant located in Iran, contains a large quantity of slimes which were transferred to the tailing ponds. These slimes have caused problems of storing and environmental aspects in the Angouran area. The objective of this research is to describe the extraction of zinc from these slimes by leaching method using sulfuric acid in pilot plant scale.Chemical analyses showed that these tailing materials contain 35 per cent of zinc. By XRD analysis, smithsonite is identified as the major constituent. Calcite, dolomite, and cerussite are found as carbonate minerals. A minimal amount of Zn occurs as hemimorphite. Quartz, kaolinite, clinochlore and muscovite are other silicate minerals in the slimes.In the optimal conditions, ie acid leach at pH of 1, temperature of 55¦C, reaction time of 120 minutes and solid-liquid ratio of 1:3 and neutralisation with Ca(OH)2 at pH = 4.5, temperature = 70¦C, time = 90 minutes, the total recovery of zinc obtained was 95 per cent.

Jan 1, 2004

By A R. A Gomes

The Metropolitan Rapid Transit Authority (MRTA) Initial System Project (ISP) - Underground Structures North, UGN, is the northern section of the blue line, which is the first stage of an underground mass transport rail system of 77 km to be implemented in the central area of Bangkok, Thailand. The UGN section (Huai Kwang - Bang Sue) consists of approximately 8 km of twin single track bored tunnels, nine underground stations and some short cut and cover tunnel sections. The paper focuses on the main issues involved in the structural design of the precast concrete lining, which is the definitive structural support of the bored tunnels. It includes an overview of the site and geotechnical conditions, specific properties of precast concrete linings, ground-structure modelling, approach for the assessment of load conditions and respective sectional forces and particulars of the detailing of the reinforcement and the segment testing program.

Jan 1, 1999

By A Mulyadi, J Barber, R Golden

The Deep Ore Zone (DOZ) underground mine will be a 25 000 tpd mechanised block cave operation starting production in 2000. The ore handling system consists of a direct truck dumping 54 +74 gyratory crusher, which feeds into an ore bin. An apron feeder below the bin is used to load a conveyor belt. This paper describes the design, sequencing and methodology of the crusher station, ore bin and feeder chamber excavations. The Geotechnical investigation and analysis of the site are also discussed as well as the design, installation and quality control of the long-term ground support methods.

Jan 1, 2000

I propose to speak today about our mineral heritage. In common usage "heritage" refers to the past. It means the discoveries, the developments, the mines and the processing plants, the benefits, the consequences, and the human experiences flowing from these. The history of the industry, inseparable from the history of the countries in which The Institute operates, is a rich background of which we can all be proud.But there is also a much wider meaning to mineral heritage. Our past has left us with the ab\lity to create and operate world scale enterprises generating wealth for the community, the ability to offer satisfying and challenging careers in a wide range of skills to our young people, and the willingness to follow adventurous and challenging vocations in remote areas, away from the big cities, at a time when the mentality of many is to get the most for the least effort and at the least inconvenience to themselves. The industry continues to be the repository of the pioneer spirit and a vital contributor to improving the life of the people in our countries.Thus, while our mineral heritage has much to do with the past, an essential part of it is how we use this rich past to build and shape our future. It is in this broader context that I am speaking today.

Jan 1, 1990

By J Szymanski, S Planeta

Extensive rockfill cylinder testing was performed to determine the effect that aggregate size, aggregate moisture, Portland cement, fly ash and cement dispersant addition has on compressive strength of a cemented backfill. In this paper ætwo-level factorialÆ and æcentral compositeÆ designs were used to determine the single and interaction effects that each factor have on the overall strength. The results from the designwork indicated that the per cent of aggregate fines had the greatest influence on the compressive strength of the rockfill cylinders. From the factorial design results, a compressive strength estimation equation was derived, which enables the strength to be estimated, given varying input values.

Jan 1, 1998

By D Chalmers, C R. Ward, B B. Beamish

Coal workers’ pneumoconiosis (CWP) has re-emerged as a major concern in the Australian coal mining industry. Harmful effects from coal dust inhalation have been well documented, but the underlying causes and mechanisms of CWP are still debatable. Research conducted in the USA has proposed a plausible link between the presence of pyrite in coal and the prevalence of CWP. Reactive pyrite in coal oxidises under ambient mine conditions to produce various iron sulfate minerals such as melanterite, rozenite, roemerite and szomolnokite. Rapid reaction rates are promoted by the form (size and morphology) of the reactive pyrite present, which provides both increased surface area and increased porosity for easy air access to reaction sites. The products formed from reactive pyrite oxidation are often needle-like crystals with thicknesses in the order of 1–2 µm (eg melanterite and rozenite) and prismatic crystals with thicknesses less than 5 µm (eg roemerite) have been recorded. The densities of these minerals are significantly less than quartz, which makes them prone to becoming airborne with the normal coal dust. In fact, the mix of these mineral salts is commonly referred to as ‘fairy dust’ by mine workers due to the way they can become entrained and sparkle in the mine ventilation air, particularly if they occur in the upper part of a seam that is forming a coal roof. Examples are presented of the various products of reactive pyrite oxidation found in three Australian coal samples, which provide evidence of the physical and chemical mechanisms that would support the USA findings, particularly in terms of a source of bioavailable iron leading to increased inflammatory stress response.CITATION:Beamish, B B, Ward, C R and Chalmers, D, 2017. Products of reactive pyrite oxidation in the mine environment – implications for coal workers’ pneumoconiosis, in Proceedings Australian Mine Vent Conference 2017, pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By W Uhlmann, U Grnnewald, B Nixdorf

Flooding with surface water is the preferred technique for the abatement of acidification from pyrite oxidation in the lakes of abandoned Lusatian lignite mines. However, water resources of the region are limited and in addition, interruption of water inflow during the summer and the termination of the flooding process after reaching the final water level can lead to a re-acidification of the lakes. The development of three mining lakes with a surface-water flooding history of six to 28 years was analysed û in two lakes on the basis of fortnightly to monthly hydrochemical monitoring data. During summer flooding interruption, the younger lakes showed a decrease in pH from neutral down to pH 4. The degree of the pH decrease depended on the intensity of the groundwater inflow from the overburden dumps and this affected the hypolimnion more than the epilimnion. The third lake was flooded 28 years ago and up to now, interruption of the surface water inflow resulted in re-acidification. These three examples were able to show the benefits and limits of the surface water flooding technique for the abatement of Lusatian mining lake acidification.

Jan 1, 2003

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3 m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.   The tailings impoundment is built with an underdrainage system that collects groundwaters and waters that seep through the impoundment. The embankment and impoundment are both built to withstand the Maximum Credible Earthquake and the Probable Maximum Flood. Tailings are treated to remove cyanide and to decrease metal solubility to reduce long term risk to water quality after mining. A state-of-the-art water treatment plant is utilised to treat water from the underdrainage system and water decanted from the top of the tailings pond and stormwaters to remove residual cyanide and metals to extremely high standards with a great deal of reliability and at reasonable cost. Closure of the facility addresses long term post mining water quality issues, and rehabilitation of the area with wildlife habitat as a priority.

Jan 1, 1995

By Z Lianbi, Z Yibin, Z Youhong, P Bin

Without adequate soil available, it is difficult to rehabilitate a large area of acid mine waste dump with sustainable plant communities, which has a strong potential acid generation. In the present project, paste tailings capping method has been put forward to reconstruct plant ecosystem on acid mine waste rock dump. This rehabilitation method uses paste tailings as capillary break and plant growth media. The tailings used contained 26.3 per cent of particles of less than 20 ¦m which satisfy the requirement of grain of paste tailings preparation. The tailings are not acid- producing materials. In addition to Cu, total contents of Zn, Pb, Cr, Cd, As and Ni in tailings are lower than those in local soil. Paste tailings concentration 70 per cent ~ 72 per cent was prepared by concentrating ten per cent tailings by using polypropylenecrylic sodium as flocculation. The potential pollution risks are low by using paste tailings as capillary break layer. Plants directly grown in the tailings did not particularly accumulate Cu, Zn, Pb, Cr, Cd, As, Ni in roots, stem and leaves, which were 0.01 ~ 1.6 times of those grown in soil.CITATION:Yibin, Z, Lianbi, Z, Bin, P and Youhong, Z, 2012. Study on paste tailings capping ecology reclamation on acid mine waste rock dump, in Proceedings Life-of-Mine 2012 , pp 243-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Osetzky D, Hesp W. R

The treatment of a hydrobiotite containing 0·64 per cent copper with various soluHons showed that a high percentage (up to 90 per cent) of the copper can be extracted under mild conditions (1 M BCI, 85°C) or withsaline solutions (20 per cent by weight NaCI or NH4F, 400°C). The latter results suggest that the copper is incorporated in the interstratified vermiculite of a vermicuHte-biotite mica and the solutions (NaCl and NH4F) which reacted with the vermiculite without attacking the biotite gave the highest extraction yields.In general, extraction yields with saline solutions increased with the temperature (between 100 and 400°C) and duration (3 or 6 days) of the treatment but were not appreciably affected by the initial pH of solutions.The results of RCI treatment especially may have a bearing on the hydrometallurgical treatment of refractory copper ores where copper is tied to gangue silicates.

Jan 1, 1977

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral valuations are still as apt to vary from realised performance as at any time in the past. As well, mineral property valuations are now being extended to cover all assets of potential value, including valuation of exploration tenements with or without identified resources. Valuation of exploration tenements will continue to be one of the most difficult and contentious of valuation tasks.

Jan 1, 1994

Kinetic Dependence of Refractory Gold Sulfide Biooxidation Using Different Microorganism Association In this investigation, refractory sulfide concentrate from a deposit located in northern Russia was treated using biohydrometallurgical technology. The objective of this work was to compare the accelerated refractory sulfide concentrate biooxidation abilities of the pure and mixed mesophilic and moderately termophilic acidophiles cultures. Pure culture of Acidithiobacillus ferrooxidans and two associations of the: Acidithiobacillus ferrooxidans + Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans + Acidithiobacillus thiooxidans + Leptospirillum + Sulfobacillus were used in this investigation. Results of sulfide concentrate bioleaching were analysed using the enzyme catalysis theory. Different effective kinetics parameters were calculated for Michaelis-Menten equation, such as Michaelis' constant and maximum rate of the enzymatic reaction. It was shown that the increase of microorganisms' species decreased Michaelis' constant. Lower Michaelis' constant characterises increasing bacteria ferment affinity to substrate (treated concentrate). As a result, the rates of sulfide minerals biooxidation have increased. This investigation has demonstrated that cultures of the different microorganism species, including moderately termophilic, allow to enhance different parameters of the biohydrometallurgical technology for the refractory gold sulfide concentrate treatment. We can see that bacterial leaching stage duration decreased and sulfide minerals oxidation increased. When the bioresidues were subjected to the hydrometallurgical stage, which includes aeration and sorption cyanidation, the operation factors were also enhanced. The decrease of aeration duration and the growth of the precious metal extraction by sorption cyanidation was achieved. Cyanide consumption was also reduced. The results of this investigation were used in design of an industrial plant.

Sep 13, 2010

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

By P Vasconcelos, X D. Deng

Numerous supergene manganese oxide deposits are developed inSouth China as a result of weathering of a thick sequence of Paleozoic marine Mn-bearing sedimentary rocks, consisting mainly of limestones, cherts and black shales that were intensely folded and faulted due to multiple episodes of tectonism since the late Triassic. The ore minerals are dominantly pyrolusite, cryptomelane, nsutite, lithiophorite and braunite. The supergene manganese ores contain Mn ranging from 20 to 44 wt per cent; manganese oxide deposits derived from cherts and black shales also contain recoverable levels of Co, Ni, Cu, Pb and Zn. 40Ar/39Ar dating of potassium-bearing manganese oxides reveals that extensive supergene manganese ore formation started at least in the earliest Miocene and persisted to the Present. Ages of the deposits show a close correlation to tectonic stability, with the oldest in tectonically quiescent areas and the youngest in active areas that have subjected to continuous uplift and thus significant denudation. The prolonged wet and hot climate since Oligocene and the balance between weathering and erosion, which is parameter to the tectonic stability, are the ultimate controls on the formation and distribution of South China supergene manganese oxide deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Mineral Changes that Occur During Coal Gasification

Sep 13, 2010

By J K. Claflin, S R. La Brooy

A case study from a current Ausenco project is presented to demonstrate the importance of maintaining high carbon activity to illustrate the driving force for plant improvements such as a carbon regeneration kiln upgrade.This paper revisits the factors that influence carbon activity for gold loading, with emphasis on deactivation by organic solution components such as flotation reagents.Kiln process design requirements for effective thermal regeneration are reviewed including the interaction of parameters such as temperature, kiln atmosphere and residence time.The different types of kilns that have been used for carbon reactivation are described. A check list is provided of what to look for when purchasing a carbon reactivation system for dealing with severely fouled carbon. This covers the ancillary equipment as well as the kiln itself.While the effectiveness of the carbon reactivation kiln is vital to maintenance of high carbon activity it needs to be remembered that this is only the end of pipe solution. It is also important to ensure that reagents such as frothers and flotation collectors are appropriately chosen to maximise recovery and at the same time minimise carbon deactivation.CITATION:La Brooy, S R and Claflin, J K, 2013. Carbon management in a high gold price environment, in Proceedings MetPlant 2013 , pp 455-467 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

In terms of tunnelling the mining industry is generally thought of as the crude cousin of the civil construction industry. Mining has tended to concentrate on speed and flexibility rather than the high standards required in civil tunnelling. Historically this difference has been based on the belief that such high standards were not required by the mining industry, they would slow down the development of the project and as a result increase the costs and extend the time period between start up and a positive cashflow.For civil works the construction of a tunnel is the project, for mining the construction of declines, crosscuts and drives are merely the means of accessing the orebody so that the real work can begin û MINING. Extraction of ore is the core business of most mining companies û it is what pays the bills.Though most mining companies have the equipment, the people, the knowledge and the ability to excavate tunnels, in the past mining companies did not appear to put the same energy into their tunnelling operations as they put into improving their ore extraction operations. In the past decade this appears to have changed, many mining companies now realise how important the correct excavation of a decline is to the success of the overall mining operation. They began to recognise that there were cost benefits to be gained in using the correct development techniques without overly sacrificing the benefits of speed and flexibility.This recognition also coincided with the growth of underground contractors whose predominant work was primary development (declines and ore access crosscuts and drives). The contractors again had the same knowledge, the same people, and similar equipment but their focus was different from that of the mining company û the contractors were focused on the development of the mine, the excavation of declines, crosscuts and drives. These deliverables were the contractorsÆ core business û itÆs what paid the bills.

Jan 1, 1999