Search Documents

By L C. Thompson

This paper examines six sites in Northern Nevada where soils and groundwater have been contaminated with petroleum hydrocarbons and/or organochlorine compounds. All six of the sites studied are located in an arid, highly mineralised area of the Great Basin. As a part of the original geochemical investigation to determine the applicability of biodegradation in the remediation of petroleum impacted soils and aquifers extremely high levels of uranium, vanadium and molybdenum were detected in the anaerobic groundwaters associated with some of the hydrocarbon plumes. Some groundwater uranium concentrations exceeded 7 ppm while vanadium and molybdenum concentrations reached almost one ppm. The bioleaching appeared to be most effective under methanogenic conditions and was noted in both high sulfide and low sulfide environments. Background concentrations of uranium in the formation were measured between 6 ppm and 109 ppm and highly dependent upon depth with the highest levels being found in association with evaporites. Unlike uranium, vanadium tended to concentrate in free-floating organic fractions reaching levels as high as 2000 ppm in the layers of jet fuel floating above the groundwater. Molybdenum was the most resistant of the three metals to bioleaching.

Jan 1, 2004

The kinetics of chlorination of alumina and bauxite with CO/CI2 mixtures were studied in the range 300-1100°C. The temperature of prior calcination is critical in determining the reaction rates. An optimum chlorination temperature in the range 600°C-750°C was demonstrated such that there is no increase in reaction rates with increasing temperature. This lack of rate sensitivity to rising temperature is largely a function of the influence of gaseous diffusion gradients in the porous alumina together with a progressive decrease in surface area.

Jan 1, 1976

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

Roadheader tunnelling machines have been used in Australia by both mining companies and contractors involved in the mining and con- struction industries since the early 1970's. They have both advantages and limitations, and this paper discusses machine excavation from the point of view of a contractor who has both reaped the benefits and suffered the conse- quences of using roadheaders. The paper also includes brief descriptions of three projects tackled by roadheader, all the projects being Declines.

Jan 1, 1987

The Pacific Rim countries ofAustralia, New Zealand, Papua New Guinea, Indonesia, Fiji, Philippines and Solomon Islands will be reviewed from an equity investors perspective.   The following areas will be covered: Country risks Exploration spending and activity Project development Taxation Relative cost of doing business Environmental considerations Political/bureaucratic situations Capital raising Equity markets as a source of funds Developing market funds The aim of the paper will be to outline the most attractive areas for investment by equity and private funds plus documenting the changes needed in the less favourable countries if they are to attract investors.

Jan 1, 1995

By Johnson N. W, Ralston J, Lauder D. W, Smart St C R

The flotation behaviour of the Hilton ore of Mount Isa Mines has been examined in the presence of two collectors (sodium ethyl xanthate (Ex) and sodium diisobutyldithiophosphinate (3418A)) over a range of flotation Eh values and collector additions. Tests were also conducted in the absence of collector to determine the relative contributions of natural and self-induced floatability of the major minerals in the feed. In these tests the influence of metabisulphite on the self-induced floatability of the minerals was also determined. Attention focussed on optimising the selectivity of galena flotation. It is shown that the Hilton ore sample contained lower levels of naturally hydrophobic iron sulphide minerals than are generally contained in the Mount Isa lead-zinc ore. Furthermore, the self-induced floatability of galena was less than that exhibited by the galena in the Mount Isa lead-zinc ore. Sodium metabisulphite (MBS) reduced the self-induced flotation of galena but had no effect on the natural floatability of the iron sulphide minerals.

Jan 1, 1991

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By J Robinson, D Herbert

Bench stoping operations at the Isa Lead mine have been underway for over 11 years. They were implemented to address safety, productivity and mining cost concerns noted with cut and fill mining operations which were then being used to extract ore from the Racecourse orebodies. This paper describes the main features of benching operations at the Isa Lead mine and identifies the key elements for the success of the method. Four case histories are presented which highlight several of these factors.

Jan 1, 1998

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974

Air tabling of zircon-rich non-conductor products containing quartz enables most of the fine quartz present to be rejected without a markedloss of zircon. The coarser quartz in the air table feed can be separated from the zircon by screening one or more air table products, the oversize products containing most of the quartz and little of the zircon. Air tabling, with or without screening, is more efficient than wet tabling alone for the removal of fine quartz, but not for the removal of coarse quartz. Practically all of the quartz can be separated from the zircon by using wet tabling in conjunction with hydraulic classification, or by using air tabling in conjunction with dry launder treatment, in which a degree of sizing takes place that is advantageous for subsequent air tabling.INTRODUCTIONBack-dune and inland beach sand deposits usually contain fine wind-blown quartz, and neither spiral nor wet table concentration, alone or in conjunction, makes a clean separation of heavy minerals from quartz. Many rutile plants recover rutile and zircon from a low-quartz, wet-table concentrates by means of magnetic and electrostatic separation; some rutile and zircon are lost in the table tailings. Other rutile plants, and two of the ilmenite plants in Western Australia, recover rutile or ilmenite respectively, from a spiral concentrate containing several per cent of quartz, and then subject the non-conductor product to an additionalgravity concentration process to separate the zircon from the quartz. Some zircon is lost in the additional gravity process, but all of the rutile or ilmenite in the spiral concentrate is, or should be, recovered as high-grade concentrate. The higher recovery of rutile or ilmenite by this treatment method is offset by the expense of drying part of the feed twice, as a wet process is usually used to separate the quartz...

Jan 1, 1962

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

Geostatistical analysis, resource estimation and three-dimensional modelling of the gold grade distribution was undertaken using exploration drillhole data taken from the Mt Leyshon gold mine. The main aims of the project were to provide an independent estimate of the primary gold resource and to improve the estimate by better understanding the statistical distribution of gold and the establishment of more robust variograms. These criteria have been achieved by the removal of low grade sub-populations, increased sample size and access to data from the most recent drilling program. The outcome of this statistical study has led to a lowering of the sill and nugget variance of the variograms used. Distinct geometric anisotropy was identified in all the resource estimation zones and was used to model gold grade distribution.Two independent resource estimates were established from the primary gold resource, one based on a geostatistical estimator (kriging) and the other on a traditional estimator (inverse distance weighting). Both methods were compared with a contemporary kriged estimate by Mt Leyshon Gold Mines Ltd.

Jan 1, 1993

By Perring CS, Vearncombe J. R, Ho SE, Groves DI

Large Late Archaean greenstone belts in Western Australia, Canada and Zimbabwe, contain abundant mesothermal gold, volcanogenic massive base-metal sulphide, and komatiite-associated Ni-Cu mineralization. These greenstone belts are similar in many respects to convergent and accretionary plate margins found in the Pacific rim; modem environments which are cor-respondingly rich in gold and base-metal mineralization. The giant gold placer deposits of the Late Archaean Witwatersrand Basin (the world's largest gold producer) formed in a foreland or retro-arc basin; in a similar tectonic setting to much modem placer mineralization around the Pacific. Gold and volcanogenic base-metal sulphide mineralization are abundant in Late Archaean terranes and the Pacific rim because1. gold mineralization is a product of convergent margin tectonics, and 2. accretion in convergent margin orogens provides the best chance of preserving base-metal mineralization related to submarine volcanism.It is therefore likely that the abundance of gold and base-metal sulphide mineralization in the Late Archaean reflects the widespread growth and sta-bilization of continental crust via tectonic processes broadly similar to those operating in the present Pacific basin.

Jan 1, 1990

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By N Davies, M J. Coward, P L. Hissey

Mount Isa Mines has four mining operations in Mt Isa with the X41 and Enterprise Mines producing copper and the Lead Mine and George Fisher producing lead zinc and silver. Each stream contributes ore to their respective concentrator at a feed rate and therefore metal ratio set out by the monthly schedule. Mine Planning and scheduling lead to a sales and operating plan (S&OP) and revenue projections which ultimately derives actual revenue /tonne and therefore cost/tonne. At Mount Isa, both the copper and lead/zinc streams produce ore from relatively new operations to be blended with material from more mature operations. It is critical to accurately predict the metal contribution from each operation in order to gauge the relative performance of each mine. Development mining ore contributions are estimated and reconciled, as are stope and bench sources. Performance is continually measured and assessed during extraction and grade adjustments are made to account for underbreak, overbreak and design modifications. It is critical to not understate or overstate the contribution from one operation relative to the other as this can produce a false picture of operational performance. Identifying process improvements are key to improving the business overall. Ore from the lead stream passes 17 measurement stations and two midstream reconciliation points before delivery to the heavy media plant (HMP), where the metallurgical circuit begins. From this point two concentrates are produced. A zinc concentrate for treatment off site and a lead concentrate for further on site processing. The lead smelter takes 100 per cent of Isa concentrates as well as a contribution from BHP-BillitonÆs Cannington Mine.

Jan 1, 2002

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008