Search Documents

By G Harbort

Traditional engineering design for flotation circuits use the “Rule of Thumb” approach. Typically this uses a nominated maximum head grade for design. A scale-up factor is applied to laboratory flotation tests for residence time. This scale-up factor is usually based on a designers experience at other flotation sites and may or may not be relevant to the circuit being designed, or the flotation equipment being used. A small number of locked cycle tests are assumed to represent the ore body and the results of these are often used for financial analysis, independent of changes in mine plan throughput and mineralogy.The engineering “Rule of Thumb” approach is only strictly accurate where there is very little variability in throughput, head grade and mineralogy. It may provide accurate design for mature established operations where a brownfield expansion is being considered but is unlikely to provide accurate design for a new, greenfield site.The use of geometallurgical modeling with floatability component simulation provides a design methodology with significantly less associated risk. The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to use spatial metallurgical information to drive production planning, mine planning, blast design, blending strategies and plant set-up. At a design stage the process designer can use geometallurgical information to evaluate bottle necks and potential design flaws and propose the best investment strategy for the project benefit.This paper details the geometallurgical characterisation of the Andash deposit and methodology used to review the project’s detail design and projected production.

Aug 8, 2011

By M J. Nugus

The structural models developed by exploration and mining geologists are most commonly concerned with the ‘main structures’ or key constituents that pertain to the associated mineralisation. To this end, it is recognised that the geological and exploration models, which are developed, are essentially ‘fit for task’ and the scale-related variances are not always realised at an early stage. In fact, in many cases anomalous intercepts along different trends and of variable apparent continuity have often been neglected as ‘back scatter’ and not important. Recognition of the importance of subordinate structures as mineralising hosts suggests that additional opportunities exist outside the primary and main structures. History shows that opportunities are often not realised where gold is hosted in orientations not parallel to the predominant trend of the schistosity, main fault or shear zone.Another reason for the importance of subordinate structures can be understood from their roles in a percolation network. Subordinate structures can access the large fluid fluxes provided by backbone elements, but, as dangling elements, they provide greater opportunities for gold precipitation mechanisms and hence may constitute essential parts of the resource. Therefore, the role, understanding and consideration of the smaller-scale and orthogonal structures should be considered during all facets of exploration, resource development, delineation and mining.

Aug 22, 2011

By C Berglin

Is the Northern Territory different? Certainly it is more remote, has less people and relies more heavily on two or three industries for its survival. On the other hand, its mining industry is governed by Acts not dissimilar to those of the major States - a Mining Act provides the basis for acquisition of tenure, a Mine Management Act provides regulatory control, a Mineral Royally Act collects revenue in return for the right to utilise the land's bounties, an Environmental Assessment Act provides the public face to rehabilitation and environmental safety, and the Aboriginal Land Rights (NT) Act purports to give development criteria for inalienable land use. With the exception of the latter, at least until the advent of Mabo, all these are simply variations on a theme, and are common to most States. This paper will show how the Department of Mines and Energy works in relation to the Northern Territory mining industry.

Jan 1, 1994

By R Goddard

An alternative stoping method has been adopted for narrow vein stoping at the Tasmania Mine in Northern Tasmania. Colloquially described as ‘Radial-in-Reef’ (RiR) stoping, the method employs the drilling of radial rings in the plane of the Reef from a drill stub located at the geographic centre of the proposed stope panel.Production from the Western Zone of the Tasmania Reef has been undertaken remotely from the Reef since 2007, after a detailed geotechnical engineering analysis indicated that the integrity of the sill drives could not guarantee an acceptable level of confidence should an anticipated seismic event occur within a radius of 10 m. The key tenet of the remote mining approach was the exclusion of personnel from sill drives once stoping had commenced. The remote mining method had to be ‘retrofitted’ to four existing stoping blocks totalling 11 sill drives which totalled 160 m vertically. The remote mining method proved to be complex, cumbersome and very expensive. However, the ore was extracted successfully.By early 2010, previously developed ore had largely been exhausted and the future development with an orebody open at depth presented the opportunity to review the current extraction method. However, the new extraction method needed to maintain the tenet of excluding personnel from sill drives of active stoping blocks, but seek opportunities to reduce the difficult and costly aspects of the previous method. The new ‘Radial-in-Reef’ stoping reduced the development requirement from six to two drives per ore block. Cost implications aside, the significant reduction in prestoping extraction ratio was expected to also reduce the likelihood of seismicity. Transverse production rings were designed to be drilled radially from a drill stub mined from a mid-stope footwall drive. Stopes totalling up to 7000 tonnes were planned be fired in a single electronic blast. Extraction was designed to take place from a basal sill drive under teleremote operation. At the time of writing, the method was under trial.

Mar 21, 2011

By M Nagarajan

Orica Mining Services (Orica) in partnership with Coal and Allied’s Hunter Valley Operations (HVO) has developed a risk management process to maximise mining efficiency whilst controlling vibration and maintaining critical electricity continuity to New South Wales (NSW) electricity grid in the Riverview Pit. The issue is a high tension tower which supplies electricity located within 40 m of mining and blasting activities. The process involved developing an understanding of the relationship between vibration, explosives, geology and the location of the blasting in the geological horizon. From this an optimum methodology for blasting in each region was developed.

Nov 8, 2011

By E R. Ramanaidou

The value of Raman spectroscopy to undertake mineral and chemical characterisation of iron ores was assessed by applying the technique to representative samples of banded iron-formations (BIF) and a BIF-derived, martite-goethite ore. The common iron oxides haematite, magnetite and goethite as well as gangue minerals such as quartz and carbonates all show distinct Raman spectra that enables these phases to be easily detected and mapped in situ for either samples prepared as polished blocks or unprepared material. Raman spectroscopy also offers the potential of in situ chemical characterisation. Shifts in the excitation bands of carbonate detected in BIF were related to the Mg content of Fe-carbonate and confirmed the first world-wide occurrence of a high Mg-bearing siderite (pistomesite) in BIF.The discriminatory power of Raman spectroscopy coupled with the potential of the technique to offer large-scale (volumetric) characterisation of iron ore will be of great value not only to the existing BID and CID ore types, but also to the newly emerging magnetite iron deposits (MID).

Jul 11, 2011

By ALAN J. HARGRAVES

It is normal that Shepherd and Rixon, in their contributed discussion (this issue) see differences with Hargraves (1983), as it exemplifies the present uncertain situation worldwide, a situation expected to remain until better understanding and wider agreement lead to the real goal of the prevention of instantaneous outbursts of coal and gas.

Jan 1, 1983

By O Rojas

The Telégrafo copper – gold deposit is located in the Centinela district of the Antofagasta region in northern Chile. Telégrafo is a porphyry copper deposit of Eocene – Oligocene age which has a total mineral resource in measured, indicated and inferred categories equal to 2.6 billion tonnes with an average grade of 0.38 per cent copper.Currently the project is in the prefeasibility study phase, including an infill drilling campaign to improve the knowledge of the deposit that should result in an improvement of the mineral resource classification. In this context was decided to review the classification criteria in order to optimise the drill hole density necessary to support the project.This paper presents an application of conditional simulation to evaluate the risk related to drill hole spacing, using a geostatistical approach that mimics the process of evaluation of resources from the perspective of geological modelling and grade estimation. The first step of the approach is the generation of conditional simulations using the available samples to generate several plausible scenarios of the deposit in terms of copper grades and geological units. These scenarios are considered as the unknown reality of the deposit and sampled by synthetic drill holes in order to replicate the geological model process and copper resource estimation. In this way it is possible to establish differences between the possible scenarios and the generated resource estimation models for several simulated drill hole spacing alternatives. These differences or errors can then be quantified in terms of estimated mean, metal content and tonnage over different production volumes.The resulting errors were useful in assisting the decision making process related to the design of drill hole spacing for each category of mineral resource in the Telégrafo project, and to redistribute the budget associated to the drill campaigns for the next stage of the project.

Aug 22, 2011

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By J M. Wallis

Heavy mineral sand exploration drilling prior to the 1970s generally utilised open hole auger and air-blast type drilling. However, mining reconciliations were poor and limitations on accuracy and precision of drilling results were severe.Working with the exploration companies, Wallis Drilling principals designed various systems, including what was termed the ‘Eneabba System’ and then the ‘Capel Twin-Tube System’. Eventually the company with its improvements developed and patented the Aircore Drilling System.Aircore drilling has subsequently become recognised as an excellent drilling system for exploration and mine-sample drilling that gives good precision and accuracy in sampling both above and below water. Its use has also been extended to many other commodities and is used in a number of overseas countries.This paper documents anecdotally the development of the system, identifying problems encountered during the times it was evolving and of the means to overcome the problems as being the documentation of the story by the inventors and developers in Wallis Drilling Company. Aircore drilling system is a Western Australian technological development owing its existence to the designing and incorporation of a number of discrete improvements along the way and recognises the tenacity and inventiveness of all who contributed to the system, in both Wallis and also in a number of companies that gave the impetus to succeed.

Oct 5, 2011

By D Connelly

As the resources sector becomes tougher with rising costs and cyclical metal prices, mining companies need to continue to reduce their costs and do more with less. Many new resource projects fail to come in under or on budget based on Feasibility Studies. Particularly, capital expenditure (CAPEX) proves difficult to achieve for resource projects. A number of resource projects have failed because of aggressive plant CAPEX cost cutting resulting in projects with no surge capacity and are unable to achieve design throughput. In addition, the plants are not operable because of the omissions. In recent times many businesses have also experienced the "costs" of simply implementing aggressive operating "cost cutting” measures as a strategy for solving business performance problems. This paper looks at technology driven, employment related, luxury cuts, department cuts and restructuring cuts. In the past companies used an incremental approach based on the use of past budget information as an integral part of the budget construction process going forward. The use of performance reports and Management Information Systems (MIS) is examined along with the role of continuous improvement in achieving sensible cost cutting.

Aug 8, 2011

By C J. Moran

All mines face water management challenges. Adopting leading practice water management strategies can help reduce both operational and strategic risks. While many of the water issues faced by underground mines are the same as other operations, underground mining presents some unique water management challenges. In this paper we review trends in underground mining, water use and associated water issues. We then compile a structured set of strategic and operational risks that are pertinent to underground operations. The causes, threats, opportunities and measures for controlling or mitigating the risks are summarised. The risk compilation could provide an addendum for underground operations to the Australian governments leading practice water management handbook.

Mar 21, 2011

By J G Reid

In the period since 1989 the Yabulu Nickel Refinery of Queensland Nickel has undergone a transformation both in terms of the nickel laterite ore feed and the refined nickel product. These two changes were mutually supporting, as will be shown in the following paper. It had been realised since the early-1980s that the Greenvale orebody would be exhausted by 1992. Consequently planning had been in progress throughout the 1980s for the importation of overseas ore as a replacement for the Greenvale ore. The existence of extensive lateritic ore deposits in New Caledonia and Indonesia made these locations the natural focus of attention. With the three Japanese ferronickel smelters sourcing their nickel garnierite ore feed from these locations it was relatively easy for the miners to supply the overlying limonite ore to Yabulu. This limonite ore was previously discarded as waste. The Yabulu refinery now receives about 85 per cent of its ore from these two overseas sources. The transition from Greenvale ore to imported ore occurred gradually between 1989 and 1993. It was during the ore importation planning stage of the mid 1980s that Queensland Nickel commenced the technical investigation which led to the ammoniacal solvent extraction (ASX) plant installation and the product change from nickel oxide to nickel metal.

Jan 1, 1994

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu's research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta's case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By R Young

Independent Project Analysis (IPA) is in the business of benchmarking the performance of capital projects on behalf of owner companies in the processing and extractive industries. IPA assesses between 500 and 800 projects each year. The projects are conducted globally and range in size from about $1 million to over $30 billion. Using the data, we are able to benchmark the performance of Australian projects against the rest of the world. This presentation focuses on the performance of large (greater than $100 million) projects that involve chemical or thermal processing.We regularly hear calls for more processing to be conducted in Australia but on the other hand industry leaders are concerned about the poor success rate of solids processing projects in Australia. Data gathered by IPA indicates that there is good reason for the concern. Out of a sample of 31 large processing projects conducted in Australia, 23, or 74 percent, were classed as failures. This performance is significantly worse than for similar projects in other parts of the world. The presentation analyses why the performance is worse and demonstrates that many of the reasons behind the failures were manageable by the project team. Furthermore, members of the project teams on at least half the failed projects knew that the projects were on a path to failure before the project was authorised but could not be heard.The presentation discusses how large projects that involve process design and, in many cases, new technology, need to be set up for success. *This is an abstract only. No paper was prepared for this abstract.*

Aug 8, 2011

By A L. Wills

Cliffs Natural Resources Pty Ltd (Cliffs) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three separate hubs and trucked to Koolyanobbing. There it is crushed and screened to lump and fines finished products and railed to Esperance port for export to Asian customers. Cliffs is renowned in the marketplace for its consistent product quality. In 2010, 9 Mt of ore was exported to Asia.Over the last three years, Cliffs has systematically refurbished its product quality system (PQS), to improve efficiency of production while maintaining its high standard of product quality. Particular attention has been given to reducing inventory, which has required significant modifications to the production process design.In redesigning the production process, emphasis was placed on maximising the application of the inherent blending in each of the production process steps and dedicated blending was only introduced where essential. Simulation modelling and statistical analysis of process capabilities were utilised to develop a system that optimises inventory, minimises rehandle, eliminates several decision-making steps and maintains a pull focus throughout the value chain.The new planning functions are now fully integrated and effectively control long-term grade variability rather than relying on long-term stockpiling. The production process design and the daily crusher blend plan are used to control short-term grade variability. With the upgrading of the planning processes the accuracy and consistency of algorithms for lump per cent and lump and fi nes grades became more important and an increased geometallurgical function has been added to the company.The continuous stockpile management system was upgraded to increase the effectiveness of the daily crusher blend planning process and is now the sole intervention point in the production process for grade-based decisions. Grade control systems were modified to utilise advances in software and geostatistics to deliver accurate short range planning models. The reconciliation and sampling systems have also been refurbished with an emphasis on practical application and feedback loops.Accountability and transparency are provided by management reports that are generated from a centralised data warehouse and the introduction of a corrective action system. Standardised reports are available to all stakeholders and a quarterly KPI scorecard assists the management review process.The successful rejuvenation of the PQS has culminated in operational efficiency through the implementation of an integrated end-to-end process flow. Shareholder value is maximised through maximising recovery of the resource and minimising costs. Customer focus is maintained by reliably delivering product with acceptable and low grade variability.

Jul 11, 2011

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011