Search Documents

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By Hussey K. J, Morrison R. S

Recent mapping (1989-1992) by the Northern Territory Geological Survey in the Tennant Creek 1:250 000 map sheet area has resulted in substantial revision of the lithostratigraphy of the Tennant Creek Block (Donnellan, Hussey, and Morrison, in press). Briefly, the former Warramunga Group (Dunnet and Harding, 1967; Dodson and Gardener, 1978) is divided into the Warramunga Formation, and an overlying less deformed volcano-sedimentary succession, the Flynn Subgroup. The latter is conformably overlain by the Tomkinson Creek Subgroup of the Tomkinson Creek province in the north of the Tennant Creek Inlier. These two Subgroups constitute the Churchills Head Group which is essentially equivalent to the Hatches Creek Group of the Davenport province to the south of the Inlier.

Jan 1, 1994

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

By S D. Dessureault

In large coal strip mines, there are many different processes at work: stripping, overburden removal using trucks/shovels, cast blasting, slot dozer pushing, more fragmentation and further truck/shovel benches. A key component to each of these steps is the use of machines. In modern operations, most machine costs are tracked within Enterprise systems that transact costs and repair work order management. Similarly, in contemporary mines most machines are tracked using technology that provides precise performance measures for each key process. Such technologies include productivity monitors on draglines, dozers and drills and fleet management systems for trucks and shovels. Linking these two sources of seemingly disparate data û costs and performance by machine û would allow for the precise calculation of unit costs by specific machine. This is similar to an activity-based costing system, except in this machine-based system, calculations are made at an even finer granular level. There are many uses for such an integrated information system in mine planning and performance management, both in real-time and through historical analysis.A real-time fleet costs (FLC) measurement process was developed as part of a larger blending-related, multi-million dollar project centred on a centralised remote control room developed at the University of ArizonaÆs Mining Information Systems and Operations Management Mine Control Center. The FLC component of the overall blending system would allow a mine controller to manage the equipment fleet by viewing its cost in real time and, when mixed with other revenue-related components, the exact profit. For example, a mine controller may show high utilisation while still maintaining a production surplus. This could occur, for example, if the equipment is driven long distances. This might appear in traditional performance metrics as æhigh production performanceÆ, but in reality may prove less profitable. This paper discusses the technical development of the FLC, its deployment and its impact on controller performance, and compares mine profitability before and after its application.

Sep 26, 2011

By S Saydam

Professional engineers need to be able to apply university learning to practice. In particular, they have to take responsibility for interactions between technical systems and the complex social environments in which they operate. The most effective way of building this competency is through active experiential learning. We have been developing an advanced educational integrated simulation system to provide mining engineering students with an interactive and immersive learning experience that is not otherwise possible. This will give students an authentic experience in working with industry software packages, while also contextualising the learning in terms of the broader and longer-term impact of technical decisions. We have been piloting the system, in undergraduate courses in order to establish its effectiveness in building systems thinking competencies for mining engineering. For postgraduate students and professionals, the same tools and methods can support studies of more challenging and complex scenarios where mining engineers have to place their decisions within complex global industry contexts.

Nov 22, 2011

By S W. Houlding

The Certificate in Mining Studies program at the University of British Columbia, Vancouver, Canada is a collaborative initiative between mining schools and industry to provide accessible, cost-effective, accredited continuing education and training, designed to address the future needs of the global mining community. Content is provided by industry specialists and delivered through an integration of online learning, short courses and interactive webcasts. Accreditation is provided by a network of mining schools. In 2011, the program will deliver close to 100 short courses and interactive webcasts and provide 24/7 access to more than 130 online courses in six mining streams, to participants from as far afield as Tanzania, Argentina and Mongolia. The program is proving adaptable to corporate and mine site engineer-in-training and graduate-development programs, as well as providing accessible professional development opportunities for individuals. It also provides opportunities for cross-training from other disciplines and integration with mining school curricula.

Nov 22, 2011

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By Forrester P. I, Richardson W

Methane in coal mines is an ever present hazard resulting in loss of lives and serious economic consequences. For effective control of methane, ventilation alone may not be totally adequate in some situations. In order to deal with such cases, new methods for the control of methane are being researched. One such method based on biotechnology has been investigated in Canada in the past several years. This method involves bringing methane oxidizing micro- organisms into contact with coal to oxidize the methane released to non-flammable products.

Jan 1, 1988

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By G Turner-Saad

An improvement to cut-off grade optimisation theory based on geometallurgy has been completed. The improvement fundamentally consisted of taking into account mineralogical and textural characteristics instead of grades. These characteristics are related to the spatial variability of mineral abundance, association, particle size and liberation properties. Additionally, the improve- ment considered the spatial variability of mineral processing liberation and selectivity properties associated with mineralogy and texture. The enhanced optimisation enables estimation of the economic value of mining operations based on an optimum cut-off policy attributed to liberated and selected ore minerals.The enhanced optimisation was developed as an essential component of a joint cut-and-fill mining and mineral processing methodology based on mixed integer mathematical programming. The formulation considers static and dynamic modifying factors that vary over the projected life of mining. The objective function of the mathematical formulation consists of maximising the realistic expected economic value of concentrates or products of liberated and selected ore minerals, whilst minimises liberated and selected gangue minerals. The optimal solution is obtained when the objective function is subject to geological, mining, processing, marketing, smelting, refining, environmental and financial constraints. The methodology accesses geometallurgical multivariate resource models, which integrate the spatial variability of mineralogical and textural characteristics and mineral processing liberation and selectivity properties.The geometallurgical process concurrently optimises stope geometries, ore reserves, mining sequences, and mining and mineral processing production based on the enhanced cut-off of liberated and selected ore minerals. In addition, the process considers additive and non-additive transfer functions associated to mutually exclusive geometallurgical spatial domains. The transfer functions also take into consideration the blending of mineralogical and textural characteristics with mineral processing liberation and selectivity properties.This contribution presents an example of cut-off grade optimisation via mineralogical and textural characteristic, and liberation and selectivity processing parameter optimisation for a spatially variable orebody.

Sep 5, 2011

By M Danišík

Two drill core samples of haematite/goethite from the Robe River (Western Australia) channel iron ore deposits (CID) were dated using (U-Th)/He methods in order to constrain the timing of iron oxide formation and thereby provide a temporal context for CID genesis. (U-Th)/He ages (He ages) from these samples range from the late Oligocene to Late Miocene and despite a high degree of scatter, they corroborate relationships expected from the internal ooidal stratigraphy: For individual ooids, the ages from haematitic core are older than or indistinguishable from the ages of the surrounding goethitic cortex. The goethitic cortices are, in turn, older than the ferruginised wood fragments recovered from the cementing goethitic matrix.The data suggest the following succession of ore formation phases:• Haematitic cores in ooids of both samples formed in the Early to Middle Miocene.• Goethitic cortices of both samples formed in the late Middle to early Late Miocene. This appears to be the age of goethite cortex formation regardless of depth in the core, which does not support the top-down infill model, genetic model proposed by Heim et al (2006).• Wood fragments form a prominent component of the matrix and were ferruginised during the Late Miocene. Thus the data suggest that the unique environmental conditions for the CID formation existed during the Miocene.A methodological implication of this study is that the temperature utilised for He-extraction from iron oxides has a critical impact on the mobility of parent nuclides. The typical ~1100°C laser heating used for crystalline minerals like apatite or zircon induces loss of U and Th and results in erroneously old ages.

Jul 11, 2011

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

By K Schonert, K Eichas

Electrostatic separation of non-conductive materials can be accomplished by triboelectric charging. The efficiency of convential separators becomes worse in the size range below about 100 ¦m. These problems are solved by developing a new double-drum-separator. The investigations have shown the possibility of separating very fine mineral mixtures (eg quartz/calcite) in a strong electric field after tribo-charging in a special dust-feeder. The paper reports about the influence of particle size and field intensity on the separation and deals furthermore with the problem of desagglomeration.

Jan 1, 1993

By R R LARGE

In the past decade mineral deposit models have become an important tool for the exploration geoscientist. By combining genetic theories on the formation of particular deposit styles, with geological, geochemical and geophysical criteria relevant to ore location, it has been possible to more effectively focus exploration effort to the regions and local targets which have the best chance of success. However, such models have their limitations, and must be carefully and critically applied and continually updated as new technical and research information becomes available.

Jan 1, 1992

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992