Search Documents

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By R Miller

The enrichment of magnetite to haematite and haematite-goethite leads to a coincident magnetic low and gravity high within the banded iron formation. Palaeochannel deposits of pisolitic limonite can be expected to provide a relative magnetic high and gravity low in a sinuous geometry. Detrital iron deposits of conglomerate, scree or ‘canga’ might have indistinct magnetic response but will usually have a relative gravity high.These signatures provide clear discriminators detectable by a joint gravity and magnetic survey.The combination of airborne gravity gradiometry and magnetometry is particularly powerful in detecting and discriminating targets, as well as mapping lithologies and structure, across a wide variety of iron ore deposit styles. It provides detection capabilities in a platform capable of rapid, complete coverage with minimal access issues. This approach has been used in FALCON™ airborne surveys for iron ore exploration in the Great Lakes, USA; the Middleback Ranges, South Australia; and the Hamersley Basin, Western Australia.The complex magnetic properties of iron formations (particularly remanence, anisotropy and depth of weathering) prevent this approach from being simple. The use of vector residual magnetic intensity (VRMI), calculated from the measured total magnetic intensity (TMI), assists by reducing the complexity due to the different directions of the remanent and induced magnetic fields.Estimations of the density to magnetisation ratio via the pseudo-lithology calculated from the VRMI and gravity gradients provide a useful method of capturing the discriminatory power of joint magnetic and gravity gradient data.

Jul 11, 2011

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By Laxaminarayan Holla

Significant coal reserves in New South Wales lie underneath major bodies of natural and stored surface waters. In order that mining can occur safely and without any adverse effect on the surface, various statutory provisions and administrative guidelines have been framed for regulating the surface and sub-surface strata disturbance. There are particular bases for the existing guidelines and the assumptions which were made in their choice. Evaluation of the guidelines in the light of the knowledge gained during the last ten years indicates that they are conservative in some cases and can be made less restrictive without lowering the safety standards. The suggested changes include reduced width for pillars in both bord and pillar first workings and panel and pillar workings, and increased level of extraction for a given degree of subsidence. Changes, if implemented, would lead to increased coal recovery.

Jan 1, 1987

By Stephenson D. B, Burgess J, Burgess F. L, Marshall S. H

A new high intensity flotation process 'FASTFLOT' is explained and its theoretical advantages compared with other flotation systems are discussed. The results of initial FASTFLOT testing on the zinc roughing circuit at Pasminco Mining, Broken Hill South concentrator are presented and compared to recent plant data. The comparison suggests that on roughing duties, the FASTFLOT process yields superior concentrate grade while requiring less than one third the residence time of a conventional mechanical cell plant. Strategies for FASTFLOT deployment are also presented.

Jan 1, 1994

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By J Vann

The philosophical context of many activities in mine geology can be an important lever in adding value to operations. For mine geologists (including resource and grade control geologists) we argue that the tasks of problem formulation, observation and data collection, interpretation and modelling invoke various philosophical considerations whether the practitioner is aware of them or not.Constructing testable models to explain reality is the definitive aspect of any activity claiming to be ‘scientific’. A primary goal of mining geology is to build models that accurately predict reality to an acceptable degree and these include litho-structural, stratigraphic, grade control, resource or reconciliation models. What’s more, in mine geology we are often able collect additional drill samples or access new underground openings, for example, that can provide relatively rapid feedback on how predictive, and therefore useful, our models are. In this paper, we describe the key philosophical frameworks proposed for conducting scientific investigations, including falsification, the method of multiple working hypotheses and structural concepts of scientific theory. The strengths and weaknesses of these approaches are discussed and an attempt is made to relate them to activities undertaken by mine geologists. Common perceptions of what constitutes the scientific method have been dominated by how scientists do experimental physics and chemistry in particular. There are very important differences in the types of problem confronted in these experimental sciences compared to the ‘historical sciences’, such as geology, where the processes studied are unique and only evidential traces of past events are available. The philosophical implications of attempting to validate numerical geological models, such as resource estimates are also briefly considered.Some practical conclusions are drawn about how mine geology activities can be better implemented if practitioners are cognisant of the importance of philosophical considerations when attempting to gain new knowledge through a scientific investigation. We believe that the implications for creating additional value to a project or operation can be very significant when geology is applied by a practitioner with an understanding of the philosophical basis of the activities we think of as constituting a scientific investigation.Remember that all models are wrong; the practical question is how wrong do they have to be to not be useful? (Box and Draper, 1987, 74 p).The demand that theories be highly falsifiable has the attractive consequence that theories should be clearly stated and precise. If a theory is so vaguely stated that it is not exactly clear what it is claiming, then when tested by observation or experiment it can always be interpreted so as to be consistent with the results of the test. (Chalmers, 1999, 67 p).

Aug 22, 2011

By J Poniewierski, Varcos D

Efficient blasting requires constant vigilance with respect to the actual layout being used in the field. Objective measurement techniques are required in laying out a pattern as the 'by eye' or 'thumb suck' methods cannot guarantee consistent results in layout. Erratic blast results are the consequence of such an approach. In a case study at Sons of Gwalia mine, it was demonstrated that incorrect front burdens had a snowballing effect on otherwise carefully laid out blasts, resulting in both excessive amounts of boulders caused by preconditioning of bench fronts and tops, and tight digging. Both problems caused lower excavator productivity and excessive excavator damage, as well as making it difficult to set out subsequent blasts correctly. Several field measurement methods are available to aid in determining correct blast layouts and one is described in this paper.

Jan 1, 1994

By N Herault

PT Freeport Indonesia recently completed preproduction development and construction of the Big Gossan underground copper and gold mine, located in the Ertsberg mining district of Papua, Indonesia. Production has commenced with an expected ramp-up to full production of 7000 tonnes per day in 2012. The Big Gossan utilises an open stoping mine method with paste backfill.In order to deliver ore to the mill, which sits in a valley above the ore deposit, an underground production shaft and hoisting facility was designed and constructed as the key component of ore haulage. The design and construction of the Big Gossan shaft posed many challenges to the project team. Available shaft design and construction expertise were limited as this was the first shaft of its kind in Indonesia and the project was undertaken during a time of high industry demand for new shaft systems. Construction resources were also limited due to the remote location and competition with existing, producing mines for these resources and skills. The project also taxed the ability of Freeport to provide services and resources to this as well as their other projects.Completion of the Big Gossan shaft was a milestone in PT Freeport Indonesia’s plan to fully transition ore production to the underground environment in this decade.This paper deals with the various challenges faced by PT Freeport Indonesia and shaft contractor, PT Redpath Indonesia, during the construction of the Big Gossan shaft and offers suggestions to improve future shaft projects of a similar nature.

Mar 21, 2011

By McQuade C. V

Mining is an activity which has, in the past, been regarded as often leaving land in a condition unfit for further use. As the need for development that is both economic and ecologically sustainable has grown, so the issue of re-use of land after mining has become significant. During operation it is usual that mine environmental conditions which minimise unnecessary or avoidable environmental impact are agreed with the regulatory authorities . These conditions are usually set down in such a way that they can be interpreted reasonably well by both miners and regulators. However, the conditions to be met by a mining company before it can be absolved of responsibility of a site are often less clear. The close-out criteria by which the success of rehabilitation programs will be judged have received little attention in the past. These conditions are now growing in importance as the costs of rehabilitation of a mine site to an agreed post-mining land use assume greater significance in the economics of mining. This paper briefly describes the status of close-out criteria presently being applied across Australia. A comparison is made with similar guidelines from other countries.

Jan 1, 1994

By T Atchison

In-pit crushing and conveying (IPCC) systems have come under growing scrutiny as a perceived mitigation to fuel and equipment price fluctuations, labour shortages and the need to move everincreasing volumes of material. Individual vendors and delivery organisations are now offering a sometimes confusing array of systems, particularly for the dig and dump side operations.One system does not suit all operations. This paper seeks to document the factors that should be considered in assessing the suitability of different IPCC systems, with a focus on dig side equipment layouts in particular. These factors include the productivity of the systems, interactions with the drill/blast and bench operation sequence, the ease of relocation, flexibility to changes in the reserve, scalability and compatibility with other elements of the system.

Jul 11, 2011

By G Danckert

The key technical theme of ‘orebody knowledge’ has been applied by Rio Tinto in the Pilbara iron ore precinct from 1966, when operations first started there. It forms the basis of present day application, as well as planning for the future.This paper will review how the early towns and mines commenced and how they formed the basis of Rio Tinto’s early operations, on which the Pilbara precinct has been based. A profile of the last decade of Pilbara growth will be highlighted, together with the current integrated network of mines, rail and ports and the next generation of expansions.The paper will specifically describe the Rio Tinto process of significant resource evaluation, including comprehensive drilling programs and the conversion from resource to reserves. It will also describe the overall mine planning process, both from the strategic view, as well as for short-term mine plans.The ability to innovate in resource development will be discussed. This will include not only the technical dimension of changing cut off grades, use of low-grade ores and managing low-grade stockpiling and beneficiation, but also the broader application of new technology and innovation in the iron ore business.

Jul 11, 2011

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By Fawcett M

Pine Creek Goldfields Limited (PCG) is rehabilitating the Enterprise Pit to an aquatic habitat and potential water resource. This paper discusses the development and implementation of that plan. Pine Creek Goldfields Ltd's Enterprise Mine is located approximately 230 km south of Darwin. Open cut mining of the orebody commenced in 1985 and continued for eight years with 14 million m3 of ore and overburden extracted. Geochemical testing of exposed rock types in the pit has demonstrated a propensity to produce acid, and dissolved metals. A plan of management has been developed and implemented to minimise the risk of acid formation and improve the overall water quality in the final void. In developing the plan prime consideration was given to reducing the potential for pit water to impact upon the regional groundwater. An interception system was constructed on Pine Creek to divert approximately 9 km2 of upper catchment into the northern end of the Pit. Construction of the diversion system was completed in December 1993 and a comprehensive surface and groundwater monitoring program initiated. The monitoring program and associated studies are also discussed.

Jan 1, 1994

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By M Griffiths

This paper outlines an approach to high solids slurry pipeline design with data generated from a closed pipe-loop test system. The pressure and flow rate data generated is used to develop a pseudo-shear diagram for the purposes of system design. Following this approach enables the design of a full pipe flow system maximising system life and reliability. The alternative free fall system is explained and the disadvantages highlighted.Environmental and social considerations are discussed; mainly water and land use, and how designing for high solids slurry pipeline systems can be used improve these aspects of a mining project.Also discussed is how the use of high solids slurry pipeline systems can help to mitigate the risk associated with surface tailings storage facility failure, with the Bulyanhulu project used as a positive example.

Aug 8, 2011

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011