Search Documents

The mineral sands deposit of Australia pose a number of unique, and quite unusual problems for the explorationist. Most concentrations of heavy minerals have been found in the unconsolidated sediments of the east and west coasts. Mineral sands mines open larger areas per tonne of concentrate than most other mines. This is because of the shallow depth of the sands containing the heavy mineral concentrations. Obtaining tenure can, by mining industry norms, be a massive operation due to the large areas to be examined and, particularly on the east coast, the large number of land holders encountered. A commercial development can still emanate from anything ranging from a small high grade body to a massive low grade deposit, the prices currently being obtained for rutile, zircon, ilmenite and monazite, although still modest when the remarkable properties and applications of these minerals are considered, is nevertheless attractive when compared to the prices being obtained for the base metals with the exception of gold. The current interest in the location and definition of new reserves of heavy minerals reflects this relative price attractiveness. The discovery of heavy mineral concentrates does not necessarily ensure the early establishment of a mine. Because of the cyclical nature of market prices, the average returns likely over the life of the mine permit the employment of only relatively simple, low cost, mining, concentration, and separation processes. If difficult mining conditions are encountered or the removal of small contaminants by complex metallurgical processes are required, then higher market prices must be obtained. Until the market is prepared to pay more for the commodities so produced, the resource will not be economic and lower cost reserves will be mined in preference. The Australian mineral sands industry has seen many closed mines because of past failures to properly assess the data base collected during the exploration and development phases of the failed projects.

Jan 1, 1987

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

In Australian collieries, solutions to the outburst problem must be implemented in a highly competitive environment which has a low tolerance on negative productivity effects. Solutions are only applicable if the overall viability of the operation remains sound. Minimum time must be spent on alleviation and control measures. This is favoured by simple geology, advanced warning and efficient alleviation and control procedures. Research requirements in support of this include 1. an improved means of predicting the nature and location of outburst zones ahead of the face and, 2. an improved means of measuring the effectiveness of gas drainage. For additional safety at the face, a means of continuously monitoring outburst proneness is required. In general, greater emphasis is required on improved instrumentation.

Jan 1, 1987

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

By Madgwick J. C

Powders prepared from the algae Gracilaria secundata, Ulva lactuca and Ecklonia radiatawere shown to provide sole nutritional support for microbial, microaerobic, biodegradation of low-grade manganese dioxide ore. G. secundata was the most effective bacterial nutrient giving 32 per cent recovery of Mn++, at an average rate of 63 mg Mn++/litre/day and a yield of 24 mg Mn++/g dry powder in microaerobic cultures containing 1.5 per cent (w/v)MnOz ore and 3per cent (w/v) powder over 14 days. Although G. secundata was approximately half as effective as molasses in supporting microbial decomposition ofMnOz, possible on-site growth ofthe alga could be economicaIIy more practical than transporting carbohydrate to a distant mine site.

Jan 1, 1987

The accurate estimation of ore reserves is the most crucial element in a financier's assessment of the risks associated with funding a mining project. It is crucial because any deficiencies in the estimation of a company's ore reserves will be later reflected in the cash flows derived from the production and sale of the commodity. Bankers must rely on the advice of members of your institute in assessing the quality and quantity of reserves. This information helps determine the cash flows which bankers use in their credit making decisions. It is against this background that this exposition has been prepared on "what bankers require in ore reserve statements" or put another way, "what does a bank require in ore reserve statements in order for it to provide the necessary credit Approvals".

Jan 1, 1987

By Turco E, Pelizza S, Castellani F, Stanganelli V

Excavation are in progress for the building of tunnels of the waterworks in West Campania (Naples). The works afferent to part II envisage tunnelling through a miocenic clay formation over consolidated by two tunnels whose sections are respectively 50 and 10m2. Tunnel blasting is carried out by mechanical means. An excavator is used in the big tunnel, whereas in the small tunnel a roadheader machine is used for a short tract and a mechanized shield is used over a long stretch. The tunnel feature complex problems regarding stability. This is particularly so for the big tunnel whose face appears unstable. For this reason the clay on the face is sistematically bolted by means of 3-metre and 12-metre bolts. This prevent the use of a TBM for tunnel Excavation.

Jan 1, 1987

Key incompatible element ratios for metabasalts from the Early Permian Croisilles and Patuki Volcanics, South Island, New Zealand, provide constraints on the tectonic environment in which their precursor ophiolitic protolith formed. Two geochemically distinct metabasalt suites are recognised among both the Croisilles and Patuki rocks. Metabasalts from one suite exhibit the geochemical signatures of depleted tholeiites from oceanic spreading ridges (N-type MORB) or spreading centres in evolved back-arc basins. These N-type tholeiites show high Zr/Nb ratios (Zr/Nb = 37-62) and are depleted in light rare earth elements (LREE)((La/Y)N

Jan 1, 1987

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

Geosynclines have been well studied for many years, but very little has been written about the concepts of sedimentary basins in spite of the vast amount of data available. They have been regarded, perhaps, as well- understood intuitively, and therefore not worthy of study. Many of the fundamental concepts of geology were developed during the 19th Century with the construction of coal mines, canals and railways. It was a happy chance that led railway engineers in the early days to think that trains could not climb any but the smallest gradient, so, in Britain at -least, numerous railway cuttings and tunnels were made. These exposed to view and study, in a better form than Nature usually provides, a great deal of interesting geology. Because of the lack of literature about the concepts of sedimentary basins, it is not possible to be sure what the early geologists thought. It seems that sedimentary basins were regarded as recording a history of subsidence during the early stages, when a transgressive sequence accumulated; and a history of uplift during the later stages, when a regressive sequence accumulated. It seemed axiomatic that the age of folding and faulting was younger than the rocks folded or Faulted.

Jan 1, 1987

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

By Kametani H

Since pyrite is a semiconductor, the relationship between the leaching rate and the semiconducting properties is of interest. In order to investigate this relationship, a pyrite concentrate (95% FeS2) was oxidized at 90¦C (363 K) in an acid solution containing 100 g/dm3 H2SO4 and 1.0 to 25.1 g/dm3 total Fe. The suspension potential (Pt vs. SCE) was maintained at the desired values, within the range 0.40 to 0.70 V, by controlled additions of a KMn04 solution during leaching. The results were analyzed using a simplified kinetic expression. The rate constant was independent of the Fe concentration, while it increased with suspension potential. Partly oxidized samples were then prepared at varying fractions of reaction. After removing the elemental sulphur formed, they underwent thermoelectric power measurements using a packed bed lying in a temperature gradient. The value of thermo- electric power increased from about 0 to 30 pV/K in the early stages of oxidation. The results obtained are compared with those for chalco- pyrite reported in a previous paper.

Jan 1, 1987

By Hedley TP

Success for underground coal mine operators in the 1990's and beyond will be dependent upon better understanding of the dynamics of their operating environment, and extension of emerging technologies to reach new levels of output and productivity. The Collieries Division of B.H.P. Steel International Group clearly identifies with the concept of business/product life cycles - and the need to adopt strategies that can drive the business successfully into the future. Three main thrusts within BHP Collieries Division relate to: 1) Detailed assessment of current mines to determine: a) The real output potential of the current facilities. b) What factors now inhibit the full potential from being realised. c) Opportunities that exist to enhance overall mine performance. 2) Based upon the findings of these studies, putting into place cost effective strategies and systems for the ongoing "tuning" of the mine. 3) of new/improved technology primarily in areas of: a) Coal cutting and underground coal clearance. b) Controlling the overall mine gas Regime.

Jan 1, 1987

By Kepplinger W

The COREX process is a technology for production of liquid hot metal on the basis of coal (without the use of a coking plant) developing by VOEST- ALPINE AG, Austria and its subsidiary company Korf Engineering GmbH, Federal Republic of Germany. CORED is a registered trademark of VOEST-ALPINE AG and Korf Engineering GmbH. The COREXW process is based on the idea of separating the process steps realized in the blast furnace (gene- ration of reduction gas, reduction of iron oxide and melting of the reduced iron) and including partial coking of the coal.

Jan 1, 1987

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

A critical appraisal of the wide variety of processes used in the pyrometallurgical production of metals and non-metals shows that there is a strong physico-chemical and, in particular thermodynamic, basis for the variety. Based on this, a simple classif- ication scheme has been developed which makes it possible to understand the methods for extracting individual metals and non-metals pyrometallurgically and to assess which are the more attractive routes. The analysis presented shows why there are essentially two broad routes for pyrometallurgical production of metals and non-metals; viz., the reduce- refine and the refine-reduce routes. Halides have the role in pyrometall- urgical processing of producing pure compounds for subsequent reduction. The criteria which determine the selection of reduction method for oxide raw materials and intermediate halides (e.g., use of carbon, hydrogen, a more reactive metal or electrowinning) are examined critically in the paper. The treatment of sulfide raw materials is considered also, particularly the criterion for smelting sulfides directly to the metal.

Jan 1, 1987

At CPA we believe that ore bodies discovered in future will be bigger and higher grade than the ones currently known and set out targets accordingly. Discoveries over the last three decades substantiated this approach.

Jan 1, 1987

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

By Baguley PJ, Napier-Munn TJ

This paper presents preliminary resu]ts from field studies which were conducted to establish, among other things. the influence of medium viscosity on the partitioning behaviour of dense medium cyclones and drums in mineral applications, using frrrosilicon- ba_sed media. The medium vicoosit.y- was measured on-line, and partitioning behaviour was determined using ore sampling and density t r acers . The results demonstrate that viscosity is an important. operating variable, influencing ,eparat.ing density and efficiency under certain conditions. The implication is that metallurgical performance can be optimised by manipulating viscosity, either by appropriate selection of medium' characteristics or by automatic alarming and/or "ontroi using signals from the on- 1. i ne viscometer.

Jan 1, 1987