Search Documents

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By X. Yuan

"The processing behaviours of ores such as their liberation characteristics in comminution and their response in separation processes are affected by their mineralogical characteristics. Key ore characteristics which are relevant to processing, such as mineral proportions, mineral grain size, grain shape and mineral associations are routinely measured at the micro-scale in polished section using optical microscopes and SEM-based automated mineralogy systems. The application of X-ray micro-tomography to mineral processing provides the means to quantify these important micro-textural characteristics in three dimensions, removing the stereological issues encountered when measuring volumetric information in two-dimensional polished sections. In this paper we present several examples of ore textures to illustrate where X-ray micro-tomography can be applied successfully to obtain quantitative measures of ore characteristics which are useful in a variety of process modelling applications.INTRODUCTION X-ray tomography has been used as a tool in medicine for some years and is being applied in a wider range of fields including geology, palaeontology and mineralogy. In this paper we present some applications of X-ray tomography in mineral processing applications being developed at JKMRC. The availability of SEM-based automated mineralogy systems such as MLA and QEMSCAN has seen the increased use of quantitative mineralogical data measured in two dimensions in the design, operation and simulation of mineral processing plants. When the ore is amenable to measurement by X-ray tomography this technique can provide quantitative data for characteristics such as mineral grain size, shape, mineral associations and liberation in three-dimensions. The advantage of measuring these characteristics in three-dimensions is that the stereological issues which bias measurements made on polished sections are removed. X-ray tomography also quantifies the location of mineral grains relative to one another in space - a useful descriptor of ore texture. Like many measurement techniques X-ray tomography has advantages and disadvantages when compared to other techniques. One limitation is that the ability of the X-ray tomography system to discriminate between minerals is a function of the X-ray attenuation of those minerals. While the X-ray attenuation of many common minerals is sufficiently different for X-ray tomography to distinguish between them, there are some where the overlap in X-ray attenuation makes discrimination on the basis of this characteristic alone impossible. An example of this would be chalcopyrite and magnetite. However where the ore mineralogy is suitable to apply X-ray tomography, the technique provides some exciting opportunities to explore the relationship between texture and ore processability."

Jan 1, 2012

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division's Toronto meeting in April, 1960. In bringing the power engineer's viewpoint to the coal producers' attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965

By Shinji Shirakawa

The gold wire bonding technology is widely used for electrically connecting aluminum pads on IC devices to external terminal of semiconductor. In 1960?s, the tensile strength of gold bonding wire was about 100 MPa only. However, recently the wire with 300 MPa in strength has been developed. Since the gold bonding wire was started to use for IC package in early 1960?, the many types of gold bonding wire has been developing continuously in order to meet market?s needs, such as high density, small size and thin type of IC packages. Moreover, electronic equipments were used in automobile applications and also demanded good reliability under severe temperature environment. Thus Au-Pd alloy wire has been introduced instead of the wire with 4N(99.99wt%) purity gold to provide excellent reliability in Au-Al bond interface. The phenomena at Au-Al interface in the high temperature storage have been already explained by several studies as follows. There are five phases of inter metallic compound (IMC) between gold and aluminum. Just after bond gold ball on aluminum pad, Au5Al2 phase was formed and occupied almost all of IMC area. During high temperature storage test, Au5Al2 phase transformed to Au4Al phase, then this phase was corroded by Bromide (Br) ion that was isolated from molding resin. Thus the reliability between Au and Al degraded. In case of Au-Pd alloy wire, the concentrated palladium phase (Au-Pd-Al) was formed at the interface between Au alloy ball and Al pad. The Au-Pd-Al phase prevented from transforming between Au and Al, therefore Au5Al2 phase was hard to transform to Au4Al phase. Consequently the reliability at the interface between Au alloy ball and Al pad was less degradation. However, in recent study using several advanced analysis technique, Au4Al phase was found at the interface between Au alloy ball and Al pad same as the case of conventional gold wire (4N purity gold bonding wire). It was suggested that the formation of concentrated palladium phase (Au-Pd-Al) related the excellent reliability at ball bonding process.

Oct 1, 2003

By T. -W. Hong, Y. Son, S. -J. Hong, D. Choi

The characteristics of indium-tin-oxide (ITO) nanoparticles recovered from TFT-LCD panel scraps were investigated. The ITO was separated from TFT-LCD panel scraps by dissolving the color filter layer located between the ITO layer and the glass substrate. The solution was filtered to separate the ITO from the color filter component, and the filtered ITO was dissolved in the acid solution. ITO nanoparticles were then precipitated with ammonium hydroxide and organic dispersing agent, followed by heat-treatment at 600 °C. HRTEM, EDX and XRD analyses revealed that the 20 nm sized particle were composed of 90 % In and 10 % Sn, and were well crystallized to in the (222) preferred orientation.

Jan 1, 2014

By John N. Ludden, Maurice Rive, Hillar Pintson

"Quelques soixante-dix-sept plutons présents dans la Sous-Province de Pontiac et dans la partie centrale de la Sous-Province de I’Abitibi ont fait I ’objet d’une reconnaissance systématique. Ils ont été regroupes en huit suites plutoniques majeures et trois suites mineures à partir de critères géologiques et petro logiques. Parmi les suites majeures, quatre représentent I' activité intrusive la plus ancienne dans la région. L’une d' entre e/les est représentée par deux complexes anorthosito-gabbroi' ques lites et les trois autres comprennent les orthogneiss dioritiques a leucotonalitiques et les intrusions dons la composition varie de diurétique et granodioritique à leucotonalitique. Leur mise en place peut être pretectonique a syn ou tarditectonique; certains plutons sont synvolcaniques. Quelques data/ions U! Pb effectuées à propos de ces roches donnent des âges s' étalant entre 2 718 et 2 694 MA. Les données géochimiques indiquent la présence des deux lignées magmatiques, tholemique et calcoalcaline bien qu’il n'y ait aucune évidence de relations entre elles dans I' espace et dans le temps. Ces suites magmatiques différentes peuvent provenir soit d’une croute tholemique impliquée dans un processus de subduction soit directement du manteau.Les trois autres suites majeures comprenant des monzodiorites, des granodiorites et des monzonites ainsi que les deux suites mineures comprenant des syenites correspondent à un évènement intrusif plus jeunesse déroulant entre2 694 et2 680 MA. Ces roches sont syn, tarti a post tectoniques et sont enrichies en alcalins, Ba, Sr et terres rares legeres par rapport aux quatre suites précédentes. Leurs caractères chimiques prop res suggèrent qu' e/les proviennent d' une source différente par rapport à celle precedemment citee.La derniere suite plutonique majeure correspond a un monzogranite leucocrate, riche en pegmatite, également syn a tard tectonique, dont I' age n' est pas connu avec précision. ll représente le seul granite ""vrai"" de la région et dérive d’une anatexie soit des meta sédiments soit des granodiorites-tonalites plus anciennes. La troisième suite plutonique mineure correspond a quatre stocks de granodiorite porphyrique qui n’ont pas été étudiés en détail.ABSTRACTSevenly-sevenplutons have been identified in the east-centra/part of the Abitibi Subprovince and adjacent Pontiac Subprovince. These have been subdivided, on the basis of geological and petrological criteria, into eight major and three minor plutonic suite. Four of the major suite, which represent the oldest intrusive activity in the area, range in composition from dioritic-leucotonalitic orthogneisses to diorite-granodiorite/leucotonalite and include two layered anorthosite- gabbro complexes. Their time of emplacement ranges from pretectonic to syn-late-tectonic and some plutons are synvolcanic. U-Pb zircon ages for these rocks range from 2 718 to 2 694 Ma. Geochemical data indicate the presence of both calc-alkaline and tholeiitic magma series for these rocks although there is no evidence time and space relationships between the two. The different magma series also suggest the derivation of these rocks from two sources, either from subduced tholeiitic crust or directly from the mantle. Three major monzodiorite-granodiorite, monzonite, and two minor syenite suites comprise a younger inlrusive event ranging from 2 694 to 2 680 Ma in age. These rocks are syn-, late- to post-tectonica and, compared to the above four plutonic suites, are enriched in alkalis, Ba, Sr and light Rare Earth Elements.Their distinctive geochemistry suggests that these rocks were derived from a different source region than for the older plutonic suites. The remaining major plutonic suite consists of leucocratic, pegmatite-rich, monzogranite-granodiorite. These rocks are also syn- to late-tectonic but their ages are not known with precision. They are the only ""true"" granites in the area and were derived by the partial melting of either older"

Jan 1, 1990

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

By Xuanxue Mo, Kaihui Yang

"Abstract- The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Barly Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry . The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affinities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental rnicroplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820Jo Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 g/t) and recoverable amounts of Au, Tl, Gd, Ga, Ge, In. A massive sulflde zone, in which lenticular and stratiform orebodies are localized in a sulflde-carbonate-silica shale unit or sulfldic tufflte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulflde zone developed in a subvolcanic intrusion or volcanic sequence. The sulfide mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite- chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerais occur rarely in the massive ores. The massive ores are generally fine-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and dis­ placement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two dis­ tinctive alteration zones have been identified: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, trema­ lite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive mode! of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By Xuanxue Mo, Kaihui Yang

"The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Early Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry. The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affInities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental microplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820/0 Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 glt) and recoverable amounts of Au, n, Gd, Ga, Ge, In. A massive sulfide zone, in which lenticular and stratiform orebodies are localized in a sulfide-<:arbonate-silica shale unit or sulfidic tuffIte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulfide zone developed in a subvolcanic intrusion or volcanic sequence. The sulfIde mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite - chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerals occur rarely in the massive ores. The massive ores are generally fme-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and displacement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two distinctive alteration zones have been identifIed: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, tremolite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive model of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By Yun-Jie Wei

Seismic areas were in the eastern margin of the Qinghai-Tibet plain, whose structures were complicated, mainly composed of Maowen fault, Yingxiu fault and Pengxian-guanxian fault. The rapid rise of the Qinghai-Tibet plain led the crustal material of the eastern edge to move to the southeast along the faults on a large scale since the late Cenozoic; Minshan block structure and Long Men Mountain tectonic zone represented the strong nappe thrust movement as the east boundary of Chuanqing slip block; the stress was accumulating when squeezed, which to a certain extent resulted in breakdown of the crust, and earthquakes. The shock speed, high-energy accumulation, and the reversed dextrorotation of the earthquake fault characteristics et al. happened, which caused the development of secondary geological disastersts. According to on-site investigation, the typical geological disasters had thrust rock collapse, the instability deposit, the revival of potential debris flow et al. whose genetic model had been analysed.

May 1, 2009

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By D. Moffat

Rio Algom Limited has mined uranium at Elliot Lake, Ontario for 20 years. The production of this energy-generating element results in the need to dispose of low-level radioactive solid wastes and liquid effluents. Because of the wet-temperate climate at Elliot Lake, the liquid effluents are of particular importance. Radium-226 is the isotope which requires most attention, and the current practice for its control is by addition of barium chloride and retention of the resultant precipitates in large settling ponds. Analyses of typical effluents and waste streams are discussed and typical levels of radium-226, thorium-230, thorium-232, thorium-228, lead-2iO, polonium-2iO, and uranium isotopes are presented.

Jan 1, 1979

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019