Search Documents

By M. Kosugi, Y. Kon, M. Kawata, J. V. Satur, K. Mitsuhashi, C. Tokoro, K. Horiuchi, R. Kawarabuki, B. Calabia

"Liberation of copper minerals is important in ensuring high flotation efficiency in copper sulfide flotation. The high pressure grinding roll (HPGR), microwave (MW), and electric disintegration (ED) are known to feature enhanced liberation over conventional comminution machines such as jaw crushers and ball mills by producing internal stresses on minerals or mineral grain boundaries through high compressive forces, thermal expansion of minerals, and pulsed high voltage discharges, respectively. In this study, each of these methods was applied before ball mill grinding to investigate its effect on enhancing the liberation of copper minerals in a low grade and fine-grained copper ore. The copper minerals observed in the tested ore sample are bornite, chalcocite, and chalcopyrite, and their grain sizes range from 10 to over 100 µm. Calcite, quartz, and feldsparare confirmed as gangue minerals. The liberation of the copper minerals by the different methods was analyzed using the mineral liberation analyzer (MLA) and compared. The result showed that the HPGR crushing was the most effective for enhancing copper mineral liberation. HPGR bench-scale test was then conducted on the copper ore and flotation was applied on a HPGR-treated sample to confirm the improvement in the flotation performance by applying HPGR.INTRODUCTIONIn order to recover copper minerals by flotation, copper ore is usually ground by ball milling to liberate the copper minerals from gangue minerals. In the case that the fine size copper minerals are targeted, grinding of the copper ore to a finer size is necessary to increase the copper recovery. However, finer size grinding by ball mill increases energy consumption significantly, which might deteriorate the economies of the mineral processing operation. HPGR, MW, and ED have been recently the focus of researchers as new techniques for enhancing the mineral liberation in mineral processing (Tavares, 2004; Kingman, 1998; Wang, 2010).HPGR crushing is considered to generate micro cracks along mineral boundary when rocks pass between two rolls by applying high compressive force. In the MW treatment, micro cracks are reported to be generated at crystal boundaries by differential thermal expansion of crystals attached to each other. In the ED treatment, micro cracks are known to be produced by plasma current flowing along mineral grain boundaries. These treatments are expected to increase mineral liberation (Fujita, 2001),improve flotation performance(Michaelis, 2005), and reduce ball mill work index(Kaya, 2010)."

Jan 1, 2017

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988

By A. J. Brown

This paper presents an economic evaluation of resin ion exchange and solvent extraction for the purification and concentration of uraniferous solutions derived from sulphuric acid leaching operations. Capital and operating costs are related to the uranium tenors of pregnant solutions. The conclusions drawn herein apply only to cases where resin and liquid ion exchange are technically feasible process alternatives. It is shown that solvent extraction is economically favoured for pregnant solutions at tenors greater than 0.90 gpl U3O8. Pregnant solutions with tenors below 0.35 gpl U3O8 are best treated by resin ion exchange. Between these concentrations, the economics are marginal and the favoured process is indistinguishable within the limits of accuracy of this study.

Jan 1, 1979

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By Zorigtkhuu Davaanyam, Fisher Wang, Bern Klein, Amit Kumar

"The High Pressure Grinding Roll (HPGR) is an increasingly popular energy efficient solution for comminution of competent ore deposits that primarily competes with conventional crushers and tumbling mills. A significant barrier to increased adoption of HPGRs is the requirement for large amounts (one tonne or more) of sample for pilot testing which may not be feasible for most early staged projects.Various researchers have worked towards developing piston-die and JK drop weight tests to model and predict the energy requirements for an HPGR. Two small scale laboratory test procedures (the SMC test (Morrell, 2009) and the piston press tests (Davaanyam, 2015)) have been developed in recent years to provide necessary information to size an HPGR.These two methods were used to estimate the required specific energy for an HPGR unit and compared to HPGR pilot scale test results from a copper deposit. The comparison provides insight into the benefits and limitations of these tests.INTRODUCTIONHigh pressure grinding rolls (HPGR) have gained popularity in recent years because of their energy efficiency in comminution. Various researchers have suggested that approximately 50–80% of the total energy consumed in a mineral processing plant is used by the comminution equipment (Haque, 1999; Abouzeid & Fuerstenau, 2009; Wang, 2013). Haque (1999) showed that the efficiency of grinding equipment can be as low as 1%. Due to the energy intensive nature of comminution, mining industry has been forced to explore alternative energy efficient processes.An HPGR based circuit has been shown to be 10–25% more energy efficient than a conventional SABC circuit (Von Michaelis, 2009; Wang, 2013). A significant barrier to the increased adaptation of HPGRs is the requirement for a large amount of sample for pilot testing (up to 5 tons), even on a prefeasibility level. Numerous studies have been performed to utilize piston press test to analyze the performance of the HPGR circuit and to predict the energy consumption for an industrial application. This paper uses two small scale laboratory test procedures, the SMC test and a piston press test, to compare the energy requirement to the pilot HPGR data."

Jan 1, 2016

By Saravarim A.

"The aim in flotation systems is to control the grade and recovery of the product., numerical method or sampling and analysis is used to achieve this goal. Weakness of measuring instruments, lack of process knowledge, deficiencies in management and data processing in the control of flotation cells, has led the academic and industrial units to use numerical models. In this regard, using the results obtained from the experimental design carried out in the DTP line of Gol Gohar industrial and mining complex, a regression model was developed based on the analysis of variance. To present this model, after variance analysis of factors and interactions, all models were investigated and the final model was created based on 75% of the data. The model was tested with the remaining 25% of the data to confirm the goodness of the fit. The coefficient of determination for training and testing resulted 71% and 74%. Moreover, a feed forward back propagation neural network with different layers and neuron was used to model the results. The best network structure was 6-27-1 and the coefficient of determination for this network was 99% and 98% for training and test respectively. Given the complexity of neural network models and the relatively low accuracy of the regression model, neural network has a priority assuming we have access to a specialist. In addition, the results obtained from neural network can be used as expert systems to control and optimize the flotation cells.INTRODUCTIONThe primary objective of the flotation cell control is to maintain the product's (in this case tailing) recovery and grade, which represents the index for process efficiency and product quality. Continuous estimation of these indexes requires a significant amount of maintenance, and calibration of the continuous analyzers, in order to maintain an acceptable level of accuracy. Weakness of measurement equipment, lack of process knowledge and the general deficiency in management and processing of data in the flotation cell control, will lead industrial units to use smart methods such as mathematical models, regression and neural networks in near future (Panahi, Abdollahzadeh, & Sam, 2010). Artificial neural networks are inspired by the very complex structure of human brain in which millions of nerve cells solve problems or store information by communicating with each other. The duty of neural networks learning. It should be noted that learning in artificial neural networks is limited, and what is practically considered is the computing power of the network. A neural network consists of units called neurons, and has the capacity to handle a set of input data to produce a desired output data set. Each of these input and output data sets can be assumed as a vector (Soltanmohammadi & Noparast, 2006)."

Jan 1, 2016

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By Elaine Ellingham, Francis T. Manns

"The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at 0.156 oz/T Au. The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distributions, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By G. M. Ritcey, K. E. Haque

"Laboratory-scale sulphuric acid leach tests were conducted on Elliot Lake and Rabbit Lake ores in the presence of various oxidants, namely: Fe2(SO4)3, CI2, H2O2, NaClO3, MnO2, H2SO5, HNO3, Oxon e, K2Cr2O7, KMnO4, O3 and O2. Uranium extraction is significantly accelerated when an oxidant is present in the leach slurry. Uranium extraction of 96-99% can be achieved by maintaining the oxidation potential of the leach slurry in the range of400 to 500 m V (S.H.E.). A rough cost comparison of all the oxidant s indicates that the use of Fe2(SO4)3, 02, O3, C12, HNO3 or MnO2 is far less expensive than NaClO3 and the uranium extraction rates are similar to or better than with NaCIO3. For uranium extraction, it is concluded that gaseous oxygen (i.e., air or oxygen) would be the most effective and economical oxidant for the 24- to 36-hour leach of Elliot Lake ore; whereas for the 8- to I2-hour leach of Rabbit Lake ore, a strong chemical oxidant (e.g. NaCIO3, H202, 03, K2Cr2O7, H2SO5 or HNO3) would be a logical choice.IntroductionThe common practice for the treatment of uranium o res is leaching with sulphuric acid or with a carbonate-bicarbonate mixture. Generally, the latter process is ad opted when an excess (> 18%) of acid-consuming components (e.g., carbonate) is present in the ore. Irrespective of the nature of the leachant, the addition of an oxidant to the leach mixture is necessary to obtain a high uranium extraction.The maximum extraction of uranium can only take place when all the uranium is in the highest oxidation state (i.e.,U +6-uranic ion) . Because a certain percentage of uranium present in the ore is invariably in the lower oxidation state (i.e.,U+4-uranous ion) , the addition of an oxidant to the leach slurry is necessary to oxidize uranous ion to the uranic state."

Jan 1, 1982

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By E. W. O'Brien

Personnel protection involves effective grounding and positive clearance of faults. This paper deals, in a general sense, with various schemes to achieve fool-proof personnel protection and reduce, to a minimum, the effects of human error and equipment failure.

Jan 1, 1966

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012

By James F. Archibald

Testing has been accomplished to substantiate recent laboratory trials which have demonstrated that thin liner membranes, applied to rock core samples, can significantly enhance the structural performance of such rock materials. A range of Canadian polymer liner materials (MineguardTM, RockguardTM and RockWebTM) have been tested side-by-side to evaluate strength and other physical property improvements generated for two highly homogeneous, though differently sourced, granodioritic rock materials. Tests were conducted on physically similar core materials, utilizing 104 to 113 samples of each respective rock type. For both rock sample populations, cores were coated using linings at thicknesses varying between 1 and 7.3 mm, typical of the application range currently used underground by mines contemplating use of such membrane agents. Results of rock failure tests, following application of passive lining covers upon the very large sample populations of each rock type, have indicated that noticeable strength improvement and enhancement of post-yield failure characteristics can be developed by the entire range of spray-on liner materials evaluated. It is shown that all of the tested liner agent materials currently available can and do act to positively reinforce rock support capabilities of modeled core pillars. Where liner materials can be effectively placed underground, it is anticipated that they may provide similar benefit and be successfully used in partial replacement for either screen or shotcrete to provide advantageous area support for rock.

May 1, 2001