Search Documents

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By John D. Smith, Robert J. Mitchell

"There is a world-wide trend toward underground bulk mining methods employing hydraulically placed backfill. This trend is recent and therefore there is little in the literature to assist an operator in the design of backfill properties, the design of drainage facilities, the calculation of the operating forces on a bulkhead, and the control procedures considered necessary before, during and after pouring. This paper presents recommended procedures that are based on over to years of experience in the various aspects of backfilling large openings. Free-draining timber or concrete block bulkheads are shown to be a viable alternative to massive reinforced concrete bulkheads for the containment of backfill pours. Hydrostatic pressures cannot develop in backfills provided adquate drainage facilities are installed.IntroductionThe increasingly adverse relationship between mining costs and mineral values has led mining companies to develop more productive, lower-cost, bulk mining methods. This has led to the increasing use of large, more or less continuous, hydraulically placed backfill pours to enable the recovery of a higher proportion of pillar ore. The success of any bulk mining method depends on the degree of stability maintained during the stoping operations with reference to the mining rate, the performance of the backfill with respect to the per cent extraction of pillar ore, and the control of the mine structure with respect to safety and productivity. One such method has been previously described(I) where a steeply dipping orebody is being mined with a sub-level method that employs large, hydraulically placed tailings pours for delayed pillar recovery. The paper describes the rock mechanics analysis undertaken to establish the stope and pillar geometry and the approach taken to establish backfill strength requirements to prevent dilution during pillar recovery. Production with this method started in 1970 and because few, if any, large bulk pours had previously been used in- this way (judging by the lack of information in the literature), design data and criteria were needed for several aspects of the work. Methods to establish backfill quantities and pertinent ""in-place"" fill properties are described in 2, 3 and 4 in the list of references. Results of field measurements taken to establish fill pressures for bulkhead design purposes are described in 5 and 6. Laboratory large-scale model tests undertaken to confirm a fill strength design equation, which takes into account fill arching, have recently been completed. A paper describing these tests and the results will be forthcoming in the near future."

Jan 1, 1982

By B. S. Riess

A novel design for an automated uranium pellet stacking system is presented. This system is designed as a drop-in solution to the current production line to enhance the fuel pellet stacking process. The three main goals of this system are to reduce worker exposure to radiation to as low as reasonable achievable (ALARA), improve product quality, and increase productivity. The proposed system will reduce the potential for human error. This single automated system will replace the two existing pellet stacking stations while increasing the total output, eliminating pellet stacking as a bottleneck in the fuel bundle assembly process.

Aug 1, 2010

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By G. Castillo, G. Thies, C. Bissue

"Newmont’s Phoenix mine began gold production in 2006 and has since experienced difficulties in reaching design throughput due to variability in ore hardness. In 2010, a debottlenecking study was conducted, generating multiple options to increase throughput of the existing Phoenix Mill through a series of phased expansions. An option was selected in early 2011 to increase the current concentrator capacity by approximately 25% through two phases. The first phase of the project was the installation of a secondary crushing and screening circuit in order to reduce SAG feed size from a P80 of 6 inches to 2 inches. The second phase focuses on downstream unit operations in the concentrator aiming to relieve existing bottlenecks such as flotation. This paper analyzes the design, commissioning, and operation of a recently installed SAG Pre-crush circuit (Phase 1). The design discussion will focus on concept development, flowsheet design, design criteria, process models, design limitations, and control philosophy. Discussion on the integration of operating data and flowsheet into design during engineering will be presented. Actual operating data of major equipment is gathered from the commissioning and operation of the circuit and compared to the initial design models. Conclusions will be drawn on equipment design factors used during engineering, and the success of model integration into operation. The paper concludes on the successes of the project and where improvements can be made during design.INTRODUCTIONThe Phoenix mine is located within 25 miles of the town of Battle Mountain, Nevada. The mill processes copper, silver, and gold ore. Production started in 2006 and has since struggled to reach the designed tonnage of 33,600 stpd due to the variability in ore hardness. In production year 2010-2011, the Phoenix mill average daily throughput of 33,000 stpd. In 2008, a larger primary crusher (FLS 60/89 gyratory crusher) was installed to operate in parallel with the originally supplied primary crusher (Metso 50/65 gyratory crusher), in order to provide additional capacity upfront in the circuit so that the primary crushing circuit could keep up with the mill.In 2010, a mill debottlenecking study was completed to assess the various options that could be implemented to increase the current mill capacity. The study was completed in late 2010 and contained four tonnages that Phoenix could achieve through various expansion scenarios. A single option was selected in early 2011 to increase the mill capacity from 33,000 stpd to 48,000 stpd. The selected option looked at a four phased expansion that would increase the capacity of the Phoenix mill and address the mill’s current bottlenecks:"

Jan 1, 2013

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By P. Cheung, J. Gulyas, R. Clary

Over the past 50 years, the use of autoclaves in the metallurgical industry has evolved from final metal recovery (hydrogen reduction) and purification (sulphide precipitate oxidation) to treating whole ores and concentrates. Recent process developments, such as the use of autoclaves for laterite leaching, have necessitated higher temperature and pressure operations, which in turn have seen marked advancements in technology and manufacturing capabilities to keep in step with process demands. This paper will discuss the advances in technology in terms of design, materials and construction of autoclaves and liners, typical dip tube design and geometric layout. This paper will also address specific auxiliary equipment, such as acid and steam injection systems, and components, such as agitator seal systems.

Jan 1, 2004

By D. E. Pickett, J. A. Roland Faucher

"INTRODUCTIONMineral processing is undergoing growth and change at a rapid rate. The modern flotation process was discovered only in the mid-twenties, and uranium leaching in the mid-fifties. The growth of individual unit equipment size is also a recent development and is perhaps most dramatically illustrated by the increase in size and connected horsepower in grinding mills. It is also apparent in much of the equipment used in mining operations.These technical and mechanical developments have influenced the design of plants but not to the expected degree.Many metallurgists believed until recently that grinding an ore in the absence of steel results in a loEs of selectivity in the flotation. However results reported by Thornton (1), Fahlstrom (2), Canmet (3 & 4) have shown on the contrary better selectivity and improved recovery at a lower operating cost. According to the Aitik (2) plant results, the net difference in cost plus tailing value in favour of the two-stage autogeneous grinding circuit is in the order of 40 cents per ton of ore milled. Even a greater difference was indicated by the results obtained by Canmet on a sample supplied by Mattagami Lake Mines Ltd.Yet how many plants are taking advantage of these findings and how many plants are being converted. How much more improvement of the results would have been obtained if these tests had incorporated optimization of classification efficiency? By nature the mining industry and the mineral processors are conservative, and tend to emphasize the possible penalties for an unsuccessful innovation out of proportion to the potential rewards even for a significant improvement."

Jan 1, 1979

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the &apos;B-zone&apos; copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By A. de Ville d’Avray, G. Guezennec, P. Wavrer, E. Braak

The aim of the European CEReS project was to develop an innovative copper recycling route based on the coprocessing of coal production waste by bioleaching and printed circuit boards (PCBs) from Wastes of Electrical and Electronic Equipment (WEEE). Coal waste is processed by bioleaching in stirred tank reactors, and the resulting bio-lixiviant solution is used to extract copper from PCBs pre-treated by catalytic cracking. Copper is then extracted using solvent extraction, stripping and electrowinning. The whole process flowsheet combines thermal, biotechnological, physical and hydrometallurgical operations. Once the process concept has been validated at laboratory scale, a simulator of the whole process has been built in the USIM PAC software platform. The tool enables to improve the analysis of the results of the lab-scale experiments and to design industrial-scale scenarios by simulation. The results of such simulations allow to estimate the economical interest and to perform environmental impact assessment. After presentation of the CEReS project objectives and main results, the paper describes the methodology used to build the simulator and define the scenarios corresponding to feasible process routes. The main results of the simulations are then presented with technical, economic and environmental point of views. INTRODUCTION Because of rapid technological innovations in the electronics industry, electronic waste represents the fastest growing waste stream in the world, especially in developing countries (Işildar et al., 2018). Meanwhile, the global copper demand is expected to go on rising in the future. As significant amounts of copper are present in end-of-life printed circuit boards (PCBs), it becomes a necessity to develop efficient copper recycling routes. Metal refining from e-waste is traditionally performed by pyrometallurgical processes. However, the hydrometallurgical processing of PCBs, which has been shown to be technically feasible at laboratory scale with a wide range of leaching reagents, could be a less energy intensive and more flexible alternative (Tuncuk et al., 2012). However, a large amount of leaching reagent is required to leach the metals from PCBs.

Jan 1, 2019

By Kimberly Morrison

Strategically located within the Uravan Mineral Belt District of western Colorado, the Piñon Ridge Project is the first new uranium mill being proposed for construction in the United States in over 25 years. In 1992, dramatic changes to the US regulatory environment for uranium ore processing occurred making regulatory compliance an increased challenge for a new facility. Proposed as a 6.3 million tonne uranium milling operation, the mill will receive ore from a number of mines in the region. The project includes design and permitting of a uranium/vanadium processing facility, tailings cells, evaporation ponds, and ore stockpile pads. The focus of this paper is to provide an overview of the US regulations and how these regulations were applied to design of the mill facilities, as well as provide a status update on the project as the mill license application was submitted to the Colorado Department of Public Health and Environment (CDPHE) in November 2009.

Aug 1, 2010

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By Marc-André Villiard, C. St-Onge, V. Silla, J-C Milot

Rio Tinto Fer et Titane (RTFT) operates a metallurgical complex in Sorel-Tracey, Canada. In the Ore Preparation Plant (OPP), ilmenite ore is roasted through four parallel rotary kilns generating 95% of the plant wide sulphur dioxide (SO2) emissions. RTFT proactively set an annual emission cap for SO2 to be achieved by 2015. To achieve this targeted SO2 reductions, a technology evaluation and selection exercise was carried out, followed by detailed engineering and implementation. After a detailed evaluation of SO2 scrubbing technologies, the Circulating Dry Scrubber (CDS) system was selected as the most appropriate desulphurization system for this application. The system was implemented and commissioned from 2013 to 2015. General performance testing conducted in May 2015 demonstrated that the system achieved and surpassed the anticipated design values in terms of SO2 removal efficiency and hydrated lime utilisation. This paper summarizes the SO2 technology selection process, design features of the selected technology, project implementation and final performance testing of the SO2 abatement system.

Jan 1, 2015