Search Documents

By Michel Aubertin

Using mine wastes as backfilling material for underground stopes has been a common practice for more than 60 years. Waste rock and tailings are used as filling materials because they are available at a reasonable cost to support the rock walls. Backfilling is also very advantageous because it reduces the amount of mine waste disposal on the surface. In underground mines, the backfill must first ensure stability of the opening, while increasing recovery of ore and minimising dilution. It is thus critical to accurately evaluate the pressures exerted on the walls and on the barricades placed near the base of the stope. In this presentation, existing solutions for evaluating the stresses on stope walls and barricades are briefly reviewed. The authors then present recently developed analytical solutions that take into account the stress transfer from the backfill to the walls in the stope and access drift. The stress state solution, which is based on arching theory, considers the influence of the stope geometry and barricade position within the drift. The method gives the pressure generated by partly or fully submerged backfill. The solutions apply shortly after backfill deposition, when the effect of pore water pressure cannot be neglected, and also for long term conditions under a fully drained state. Experimental testing and numerical modelling results are used to validate the proposed equations. Both numerical and analytical results show that the total pressure on barricades can be significantly increased by water pressure, while the effective stress is decreased (compared to dry or drained conditions). A discussion follows on the implications of the results for backfill applications.

Nov 1, 2008

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

"The main purpose of geometallurgy is to develop a model to predict the variability in the mineral processing performance within the ore body. Geometallurgical tests used for developing such a model need to be fast, practical and inexpensive and include as an input data relevant and measureable geological parameters like elemental grades, mineral grades and grain size. Important in each geometallurgical program is to define the number of samples needed to be sent for geometallurgical testing to enable reliable metallurgical forecast. This is, however, a complicated question that does not have a generic answer.To study the question on sampling a simulation environment was built including a synthetic ore body and sampling & assaying module. A synthetic Kiruna type iron oxide - apatite deposit was established based on case studies of Malmberget ore. The synthetic ore body includes alike variability in rock types, modal mineralogy, chemical composition, density and mineral textures as its real life counterpart. The synthetic ore body was virtually sampled with different sampling densities for a Davis tube testing, a geometallurgical test characterising response in magnetic separation. Based on the test results a forecast for the processing of the whole ore body was created. The forecasted parameters included concentrate tonnages, iron recovery and concentrate quality in terms of iron, phosphorous and silica contents.The study shows that the number of samples required for forecasting different geometallurgical parameters varies. Reliable estimates on iron recovery and concentrate mass pull can be made with about 5-10 representative samples by geometallurgical ore type. However, when the concentrate quality in terms of impurities needs to be forecasted, the sample number is more than 20 times higher. This is due to variation in mineral liberation and shows the importance of developing techniques to collect qualitative information on mineral and ore textures in geometallurgy."

Jan 1, 2016

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By J. Mosher, G. Banini, J. Hollow, A. Villanueva

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By G. M. Castillo

Newmont?s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By C. Bissue, G. M. Castillo

Newmont’s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By F. Hassani, D. O’Donnell, M. Momayez, P. Guevremont

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with miniature seismic reflection technology (MSR) developed and patented at McGill University primarily for thickness measurement of this heterogeneous liner. MSR is also capable of providing information regarding the quality of shotcrete in terms of its mechanical properties such as modulus of elasticity and Poisson’s ratio. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fiber-reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring. In addition, the MSR technology has the advantage of being more accurate and more affordable compared to other non-destructive testing (NDT) systems in the market.

Jan 1, 2002

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

By S. Kursunoglu

The aim of this study was to investigate the effectiveness of Ascorbic (C6H8O6) Acid (AA), Activated Carbon (AC) and Guar Meal (C6H12O6) (GM) as a reductant for the simultaneous complete dissolution of zinc (Zn) and manganese (Mn) from a spent and mixed Zinc-Carbon (Zn-C) and alkaline battery powders in sulphuric acid (H2SO4) leaching. AA was tested previously as a reductant by other researchers while AC and GM were tested as a reductant for the first time in battery recycling. The effects of H2SO4 concentration, AA/AC/GM dosages, reaction temperature and leaching time on the Zn and Mn dissolutions were investigated according to 2k full factorial experimental design and Central Composite Design (CCD) technique; then, a simple optimization study was carried out for comparing the reductants. The optimum reductive acid leaching conditions for AA were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M H2SO4 concentration, 13 g/L AA dosage, 1/20 g/mL solid/liquid (S/L) ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. The best reductive acid leaching conditions for AC were determined at 3h leaching time, 80oC leaching temperature, 1M H2SO4 concentration, 3 g/L AC dosage and 400 rpm mixing speed. Under above conditions, Zn and Mn dissolutions were not complete. At 2M H2SO4 concentration, 10 g GM dosage, 700C leaching temperature, 200 rpm stirring speed, 1/20 g/mL solid/liquid (S/L) ratio and 3 hours leaching time, full dissolution of both Zn and Mn was achieved. As a result, three different reductants were evaluated in this study for complete simultaneous Zn and Mn dissolutions. This paper also compared present test results with previous spent battery recycling studies for Zn and Mn dissolutions. Full valuable metals dissolutions from spent batteries were achieved at low H2SO4 concentrations with AA and high concentrations with GM. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leach solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover both Zn and Mn.

Aug 1, 2013

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By Bo-Hyun Kim

Outline ? Strainburst criteria and hypotheses adapted for this study. ? Influence of excavation method on rock mass properties. ? Excavation disturbance factors vs. deformation modulus, etc. ? Estimation of blasting damage zone around excavation. ? Considerations of energy on burst-prone ground. ? Literature review & closed form solution. ? Numerical simulations. ? Summary and future works.

Oct 1, 2010

By Erol Yilmaz

This poster presents results obtained from an experimental test set-up called CUAPS (curing under applied pressure system) allowing to assess the performance and quality of cemented paste backfill (CPB) materials. CUAPS can be used for carrying out a series of tests: one-dimensional consolidation, saturated hydraulic conductivity, pore-water pressure dissipation, and curing under uniaxial stress. The poster presents CUAPS testing preliminary results including uniaxial compression tests (UCS) and mercury intrusion porosimetry (MIP). It was demonstrated that CUAPS-consolidated CPB materials cured under time-dependent stresses provide higher UCS values than standard mould (undrained and unconsolidated) CPB samples. This may be explained by the release of excess pore water within backfill that gives rise to a significant reduction in the total porosity of fresh CPB materials prior to hardening and thus, to higher mechanical strength (UCS) gain. The results obtained from MIP highlighted a good correlation between CUAPSconsolidated and mould-unconsolidated CPB samples. MIP results were also related to UCS values in order to predict the final CPB mechanical strength.

Nov 1, 2008

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009