Search Documents

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By M. Mirnezami, J. A. Finch

The McGill component of the consortium contributed detailed examination of the electrokinetic properties of the constituent minerals, primarily pentlandite and serpentine. Mineral specimens were derived from an ore sample; mineralogical examination showed the serpentine was predominantly clinochrysotile, a fibrous mineral responsible for much of the flotation separation problem. The study included design of a novel sedimentation potential measuring device to classify the surface charge of the ore and electrophoresis measurements on single and mixed minerals which progressively approached flotation conditions. The sedimentation potential measurements provided a general association between surface charge and the visual state of aggregation as a function of pH. The electrophoresis experiments started with single minerals in a background of indifferent electrolyte and progressed to mixed minerals in a background of supernatant derived from an ore sample. The single mineral tests supported the suspected electrostatic interaction, i.e., hetero-coagulation, at flotation pH 9-10. The mixed mineral tests demonstrated this interaction and also revealed hetero-coagulation with Mg(OH)2 precipitates, derived from the supernatant. This interpretation was confirmed by optical and electron beam imaging. A series of agents, CMC, polyphosphate, soda ash, EDTA, were examined to disperse the system. To accommodate the small mass of single mineral available a novel turbidity measurement using a UV/Vis spectrophotometer was introduced. Selected conditions were used in contact angle and small-scale flotation tests.

Jan 1, 2011

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By The Staff

THE property of McKenzie Red Lake Gold Mines, Limited, consists of eleven claims located on McKenzie island in Red lake. The mine is about 4,Y:l miles by water from the Howey townsite on the same lake, and about 95 miles north of Kenora, Ont. (see Figure 4). Mail and express are flown-in daily, winter and summer, from Sioux Lookout, Hudson, Kenora, and Winnipeg. All heavy supplies are freighted-in during the summer over a water route, using four marine railway portages, from Hudson, Ont., a distance of about 180 miles. During the winter, freighting over the same route is clone by tractor if necessary, but costs are three to four rimes the summer rate. Due to these conditions, large inventories of supplies must be kept on hand, varying from a spring minimum of $45,000 to a peak of $110,000 early in November. The average cost of all freight brought in from steel during 1937 was $0.01 per pound.

Jan 1, 1938

By H. Clare Horwood

"Three types of structures, the main shear zone, the north shear zone, and a series of hanging-wall fractures, contain all the orebodies so far discovered at the McKenzie Red Lake mine. Lenses and veins of quartz in these zones and fractures are the sources of the ore. The ore-bearing structures are unusual in that they are in a complex intrusive mass known as the McKenzie-Gold Eagle stock. They are believed to have been produced by compressive stresses from the south andsouthwest.The mine is on the northeast side of McKenzie island, in Dome township in the central part of the Red Lake area. The original discovery, the main shear zone, was made in 1928, about 3 years after the property was staked, by M. L. Bouzan who was in charge of prospecting and development work on the property. Subsequent diamond drilling and underground exploration led to the installation of a mill, which came into production early in 1935. The hanging-wall fractures were found branching out from the main shear zone during development work on the 350-foot level. The north shear zone was discovered in 1940.From 1935 when the mill began operation until the end of 1946 total production from the mine was approximately 269,349 oz. gold and 69,317 oz. silver, having a value of $9,679,739, recovered from 823,527 tons of ore.GENERAL GEOLOGYThe McKenzie-Gold Eagle stock has a total length of approximately 1 ½ miles and a width of about ½ mile. It was intruded into a complex synclinal fold in Timiskaming sediments. The sediments, which have been cut in only one place in the underground workings, are principally wellbedded greywackes. The stock is composed of large masses of diorite and granodiorite, a small mass of hornblende pyroxenite, and basic dykes of two ages. The diorite occurs as irregular masses in large measure surrounded by the granodiorite that it intrudes. It contains tabular crystals of andesine, having a maximum length of3/4 inch. The hornblende pyroxenite is an elongated lens or dyke in the diorite. The granodiorite masses occupy about two-thirds of the stock. Along its eastern side the main mass tends to become darker and more dioritic toward the diorite contact.Basic dykes of pre-vein and post-vein age are the youngest intrusive rocks at the mine."

Jan 1, 1954

By M. Jorgensen, I. Markland, D. Shuck

"The McLaughlin Mine owned by Homestake Mining Company is located 70 miles northeast of San Francisco in California's coastal range. The mine began operations in February of 1985. The mill currently processes 3,000 short-ton per day of sulfide ore that has an average grade of 0.15 ounces of gold per ton, plus another 3,000 tons per day in a newly completed oxide circuit. Annual production from the mine totals over 200,000 ounces.The sulfide ore extraction process involves three basic steps, grinding, oxidation of sulfide minerals in an autoclave, and cyanide leaching for recovery of gold in a carbon-in-pulp circuit. This process, which incorporates a new technology where oxidation of sulfide minerals is conducted prior to cyanide leaching to facilitate gold recovery, was successful from start-up. However, limitation in the grinding mills initially limited sulfide tonnage throughput.This paper discusses modifications made in the grinding circuit, both mechanical and operational, to resolve it deficiency. The SAG mill, in particular, was unable to achieve design tonnage initially and proved to be most troublesome. Complications occurred due to the hardness and variability of ore being processed, short component life, and a lifter /liner arrangement that had to be tailored to the particular circumstances at McLaughlin. IntroductionHomestake Mining Company's McLaughlin Mill, located in northern California, was designed to process a refractory gold ore at a rate of 3,000 tpd to render the ore amenable to cyanidation. Seven years transpired between discovery of the near-surface ore body in 1978 and the February, 1985 plant start-up. Development of the McLaughlin mill and open pit gold mine hinged on the use of autoclave technology to achieve design recoveries."

Jan 1, 1991

By M. E. Wilson

"The property of McWatters Gold Mines, Limited, is in the east-central part of Rouyn township and about 6 miles east-southeast of the town of Rouyn. It includes 35 claims, the group of 5, staked originally, and 30 claims acquired in later years. The Rouyn-Val d'Or road and the Noranda Senneterre branch of the Canadian National railway both pass within a few hundred feet of the mine.The group of claims in which the mine occurs was first staked in 1922, but gold was not discovered until August 1932 when a schistose zone including veins of quartz carrying considerable free gold was laid bare in a stripped area in the northeastern part of claim R.11604. Diamond drilling undertaken in 1932, and continued into 1933, shouwd that the gold extended for at least 1,000 feet along the strike. A 3-compartment shaft was sunk to 418 feet in 1933. A mill having a capacity of 50 tons a day was constructed in 1934, and enlarged to 150 tons in 1935. Production began in 1934 and continued without interruption to June 1944. Except for a few diamond drill holes, there have been no operations on the property since that time. The maximum depth of the mine workings is 1,50) feet. A total of 368,013 tons of ore having a value of $3,946,752 and an average grade of $11.04 was mined during the years of operation.GEOLOGYThe ore mined from the property occurred within the south limb of an eastward plunging syncline of volcanics and sediments cut off on the north by the Cadillac-Bouzan Lake fault. Because the rock formations within the syncline have been severed from those outside with which they were originally continuous, their correlation is based almost wholly on lithological similarity. They include an irregular middle zone of conglomerate and greywacke underlain by north and south bands of andesite agglomerate and andesite tuff, in which lenticular bands of pillowed andesite are included."

Jan 1, 1954

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By Stéphane Robert

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributable to accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company's total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company's historical results of operations is set forth in the notes to the financial statements included in the Company's Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By G. Shen, W. R. Tyson

In most fracture toughness test standards, such as ASTM E 1290 and BS 7448, crack-tip opening displacement (CTOD) is measured by using three-point bend (SE(B)) or compact (C(T)) samples with deep cracks. The loading mode and crack depth in these tests sometimes are different from that of pipelines. Pipelines usually have shallow defects and experience tensile loading when the supporting ground moves. As a result, the CTOD measured by these samples is lower than that of pipeline in tension. Recent researches suggest using single-edge-notch tension (SE(T)) samples to measure fracture toughness for pipelines. In the present study, shallow and deep SE(T) samples under fixed grip loading were analyzed by using the finite element technique. An equation to relate the CTOD to the area of the load/plastic crack mouth opening displacement (CMOD) is proposed. With this equation, the CTOD of a SE(T) sample can be evaluated by measuring the area under the load/plastic CMOD curve of a SE(T) sample.

Jan 1, 2005

By J. A. Finch, G. Labonté

"A long-standing objective has been to obtain interpretable measurements of the oxidation-reduction potential in mineral slurries. For this purpose several sensing electrodes (black platinum wire, platinum foil and spiral, gold foil and spiral, and sulphide minerals such as chalcopyrite and galena) were investigated to determine their response to the presence of sulphide minerals in the pulp, and to the addition of reagents commonly used in flotation. The observed discrepancies between the electrodes may be explained using a combination of the classical mixed potential model for complex solutions and the probability of contact between the mineral particles and the sensing electrode. It is shown from laboratory testwork that gold spirals are preferred over platinum electrodes. Finally, some of the practical aspects of using the electrochemical measurements in a plant environment are discussed.IntroductonThe interpretation of flotation of sulphide minerals in terms of electrochemical (electron transfer) processes has brought new possibilities for process control of selective flotation. Investigations on massive and compacted particulate bed electrodes have shown that the flotation of a given mineral in the presence of a collector can be controlled by the potential induced on the mineral surface. Also, phenomena such as collector less (self-induced) flotation, activation by heavy metal ions, and natural selectivity sustained by galvanic coupling during flotation might also be controlled by electrochemical means.The technique for measuring electrochemical potential in slurries is an adaptation of that used for solutions. The measurement of the oxidation-reduction potential of a solution (ORP , Redox, Eh) is usually carried out by immersing a noble metal electrode (platinum, gold or silver) and a non-polarizable reference electrode: Standard Hydrogen Electrode (SHE), Standard Calomel Electrode (SCE), or silver/silver chloride (Ag/AgCl) in the solution. (The abbreviation Eh implies the SHE is the reference electrode.) The potential difference between the two electrodes is measured using a high impedance electrometer. ASTM standard D 1498-76 (revised 1981)(1) covers the practical details of such measurements; however, it does not deal with their meaning either in complex solutions or in mineral slurries ."

Jan 1, 1988

By Knud Sinding

Mining firms are widely criticised for their adverse impacts on the environment. At the same time many firms in the industry devote extensive resources, both financial and managerial, to the reduction or elimination such impacts. Very considerable improvements have been made, although these are sometimes overshadowed by a few high-profile accidents, such as the occasional collapse of a cyanide-containing tailings dam. In parallel, much effort is also directed at projecting a positive environmental image, as witnessed by extensive environmental reporting, both on paper and increasingly through web-platforms. Mining projects today almost invariably involve some form of environmental protection. In industrial countries regulations in this area are extremely stringent, as is enforcement. In less well developed countries, regulation and enforcement may be weaker, but firms are in many cases and for a number of reasons committing themselves to high levels of environmental protection, even if they might get away without doing so. Research in the area of environmental performance of mining firms has so far paid much attention to concepts such as sustainability indicators and the sustainability of individual firms. Given the still raging debates about the appropriate way to determine the degree to which any given firm is sustainable (Welford 1995) as well as the usefulness of what will in the final analysis be a value judgement, anyone on the sidelines of the debate will come back to the fundamental issue, how is knowledge that a particular firm has been judged ?sustainable? going to be made use of. This issue remains unresolved, which may explain the lack of progress in formulating a useful definition of a sustainable firm The question addressed in this paper is not so much about what firms are doing on the ground or in any particular case of environmental protection, but more in the subsequent use of these efforts - and by extension - on the overall direction of corporate environmental strategy. The fundamental problem facing all mining firms is that they cannot easily benefit from unilaterally reducing their environmental impact. The firm can of course avoid liability and keep a variety of stakeholders happy and hence experience lower costs of obtaining the [input] resources they need (in a broad sense, not just minerals), but this represents only part of the opportunities available form pursuing an environmental strategy (Reinhardt 2000). The other part, which may have an enormous potential, involves the concepts of competitor management and product differentiation. The logic of keeping stakeholders happy has been most forcefully argued by Pfeffer and Salanchick (1978) who link the behaviour of firms in all domains to their ability to obtain the resources they need, at a cost that is lower than it would otherwise be (Pfeffer & Salanccik 1978). Several varieties of strategy can be included under this heading, including cost reduction and risk management. The alternative logic is to convince customers that they want to pay more for minerals supplied by mining firm X or directly attributable to mine Y, or by making all mineral users pay more. These two strategies, which may be referred to as product differentiation and competitor management, respectively (Reinhardt 2000) are related to the demand side of mineral supply, whereas cost reduction and risk management are related to the supply side. Mining firms have not pursued the demand side very much, if at all. This is probably due to the extreme difficulty of moving mineral products, bulky and unglamorous as they are, away from their

May 1, 2003

By J. Butra

The underground research presented in this paper was carried out in the two Polish copper mines: Rudna and Polkowice-Sieroszowice. The aim of the research was to determine stress field parameters. The measurement method and measuring positions are described as well as the measuring technique adapted to the geological and mining conditions of the Rudna mine and the Polkowice-Sieroszowice mine. The identified values and directions of principal stresses and horizontal stresses and their importance for optimization of mining operation and safety improvement are discussed.

Aug 1, 2013