Search Documents

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By S. D. Anitha Kumari, T. G. Sitharam

"The huge urbanisation of the world cities have invariably resulted in enormous requirements of development in transport and other facilities. As the surface space available for the construction of these infrastructural facilities is found to be inadequate, underground space is widely used recently for this purpose. However, to understand the behaviour of these underground structures through experiments under various loading conditions is not practically feasible. Hence numerical methods have widely been used to model these structures and predict their behaviour. The underground structures generally rest on soil or rock. Depending upon the properties of the material surrounding the tunnel, the deformation pattern and the stress contours vary. If the tunnels are placed on soft ground at a shallow depth, the presence of existing structures will add to the stresses and strains developed. In the case of densely populated cities, tunnelling operation may result in huge damages if the settlements are not within the desirable limits. This may in turn lead to the collapse of the tunnel along with adjoining structures. So the determination of stress levels associated with the yield of wall due to excavation is very important and necessary supports and reinforcement should be provided. Numerical simulations using discrete element method (DEM) and finite element method (FEM) have been done to understand the stress variation around single and twin tunnels. Studies are also done to quantify the improvement of stability on the introduction of lining around the tunnels in a weak cemented soil mass like sandstone.INTRODUCTIONMost of the life line facilities which include pipelines for electricity, water, communication, sewage, gas, roads, metro, utility tunnels etc in modern urban areas are underground structures. Infrastructure development is crucial for any city and sustainable development urges for underground constructions. Accordingly, there is already a great demand for tunnels to be constructed in difficult and crowded urban settings. This results in the fact that a large number of risk factors are associated with tunnels in these densely populated urban areas. These constraints pose threats to tunnel construction and also demands for minimal disturbance to the public and to the surrounding utilities. One of the most important factor to be considered while designing an underground structure is its stability with respect to the surrounding medium and adjoining existing structures. In this study, a comprehensive presentation of the numerical modeling of single and twin tunnels adopting two different methods is presented."

Jan 1, 2015

By M. Imani, A. Fahimifar, A. H. Javid

"Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study to evaluate the ultimate bearing capacity for two interfering strip footings resting on a rock mass in which the strength can be described by the generalised Hoek–Brown failure criterion. This criterion is applicable to intact rock or heavily jointed rock masses that can be considered homogeneous and isotropic.The material is assumed to exhibit perfect plasticity and obeys an associated flow rule. The effects of Hoek–Brown parameters including GSI, mi, and sci were studied and the corresponding results are presented. For different clear spacing (S) between the footings, values of the efficiency factor (?) were determined; where ? is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that of a single isolated footing having the same width. The maximum value of (?) occurs at spaced between S/B = 0.5 to 1.0. The results have been compared with those available in the literature.INTRODUCTIONEvaluating the ultimate bearing capacity of rock masses is essential for important projects like dams and bridges. Closely spaced footings may occur on rock masses in the form of pier foundation and grillage footing. Close spacing lead to permit higher loads than can be bore by similar isolated footings. The ultimate bearing capacity of two interfering strip footings resting on cohesionless soil have been studied theoretically (Kumar, & Gosh, 2007; Kumar, & Kouzer, 2008; Stuart, 1962). Results revealed when two strip footings approached closely enough, failure zones affect each other and ultimate bearing capacity significantly increased."

Jan 1, 2015

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By D. Turk, P. Lefebvre, J. Sargent, K. Major

"Stillwater Mining Company recovers platinum and palladium from their Nye Montana operations. Mining first commenced at Nye in 1987 at a milling rate of 455 t/d (500 stpd). The plant was expanded in 1995 with the replacement of the ball mill and the addition of flotation capacity to increase mill throughput to 1820 t/d (2000 stpd). The applications for platinum and palladium have increased in recent years particularly in the automotive industry and the supply of the metals has remained fairly constant with prices for both platinum and palladium increasing and remaining very stable. In 1997 Stillwater initiated the expansion of their operations to increase production of platinum and palladium. Projects were initiated to expand production at the Nye operations, increase smelter and refining capacities at the Columbus facilities and to develop the extension of the orebody at the East Boulder site. This paper will discuss the changes at the Nye concentrator which were completed to increase production from 1820 t/d (2000 stpd) to 2730 t/d (3000 stpd) and eliminate some of the process bottlenecks.IntroductionStillwater Mining Company is mining the only significant primary source of PGMs outside of South Africa. The J-M Reef is an extensive mineralized zone containing PGMs that has been traced over a strike length of about 43 km (27 miles) in the southwest region of Montana. Stillwater controls the entire PGM mineralized zone.Johns-Manville geologists discovered palladium and platinum in the early 1970’s. In 1979, a Manville subsidiary entered into a partnership with Chevron, USA to develop the project. In 1 987, operations at the Stillwater property near Nye, Montana commenced."

Jan 1, 2000

By Robert A. Brown

"The O'Brien mine is in the west-central part of Cadillac township along the Cadillac 'break', which extends for 7,500 feet from west to east across the property.The ground was staked in 1924 by A. Dumont and W. Hermeston, prospecting for M. J. O'Brien, Limited. The first vein discovered is that now known as No. 1. The No. 4 vein was later exposed on the surface; the other veins known to be present were revealed by underground work and diamond drilling carried out both from the surface and underground.The mine is developed from three vertical shafts: No .. 2 extending from the surface to 2,000 feet; No. 3 from the surface to 1,500 feet; and No. 4 from 2,000 to 3,000 feet. There is on the property a mill of about 200 tons a day capacity, the usual shops, and a townsite housing about forty-five families. Gold production to the end of September, 1944, amounted to 295,824 fine oz. from ore having an average grade of 0.505 oz. a ton. In addition, the mill recovered 3,237 tons of arsenic trioxide having a purity of 83 per cent As2O3.GENERAL GEOLOGYThe four main groups of rocks of the Cadillac area- the Cadillac, Blake River, Kewagama or Pontiac, and Malartic- are found within the boundaries of the property. However, as these rocks have been fully described in · various government reports (1,2,3,4,5,6) and all the known orebodies occur within one group- the Blake River-a detailed description of the geology will be dispensed with here. The known ore deposits lie south of the Cadillac 'break' in a group of rocks that includes 'greenstones', greywackes, conglomerate, porphyries, and a rock of gabbroic composition that may be intrusive. Both flows and tuffs can be recognized in the 'greenstones'. The two bands of porphyry that trend easterly across most of the property have been considered by some observers to be dyke rocks and by others to be flows. Certain evidence points to their being dykes that were intruded as sills considerably prior to the emplacement of the gold-bearing veins, but the possibility of flow origin cannot be fully rejected. North of the talc-chlorite-carbonate schist zone forming the 'break' the rocks are conglomerate and greywacke with iron formation, in which there are no known veins of ore grade. Within the schist zone are minor acid and basic intrusives. The general trend of both bedding and schistosity is a few degrees south of east. The dip is generally vertica1 or steep to the south."

Jan 1, 1954

By C. W. Drake, J. H. Walsh

"The Canadian Carbonization Re-search Association was formed during 1965, with seven founding members representing four integrated steel companies, two coal companies and one high-temperature tar processing company. The purpose of this paper is to review the circumstances which led to the formation of this new research association and to discuss its general objectives. Also discussed will be the organization of the Association, the nature of its relationship with the Department of Energy, Mines and Resources in the early stages, and some of the technical programs which have now been initiated."

Jan 1, 1967

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By R. Harrisson, K. Esmaieli

Brunswick mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance of ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions, etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Jan 1, 2008

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By S. Kobayashi, N. Ohara, T. Aoki, S. Sakurai, M. Iwano, M. Shimo, I. Otsuka

"This project is the upgrading of a commuter line of approximately 76 km to improve the railway system in Istanbul metropolitan area. Railway tracks have been connected between Asia and Europe through a tunnel under the Bosphorus Strait. The length of these underground structures sums up 13.6 km. In this paper, the observational construction management based on field measurement performed at large scale underground railway station (Sirkeci station) constructed by means of New Austrian Tunneling Method (NATM) is described and the mechanism for generation of ground surface settlement above this station is discussed.Buildings above Sirkeci station are overcrowded. About 60% of the buildings are made of reinforced-concrete (RC) and others are of brick. Based on the investigation into the predicted settlement and inclination, necessary actions such as structural reinforcement and soil improvement have been conducted for dilapidated buildings.Rock mass around Sirkeci station consists of alternative strata of sandstone and mudstone. It is overall soft rock with an elastic modulus of 150 MPa, partly including fractured zones. Overburden is about 30 to 40 m. The thickness of unconsolidated sand layer distributed on the bedrock is about 10 m. As a result of in-situ permeability tests, the coefficient of permeability of the sand layer is about 1.0x10-3 cm/s. Fill layer of about 10 to 25 m in thickness covers the sand layer at the ground surface. The fill layer contains a lot of artificial waste like splinters of wood, brick chips and mortar chips, etc. in addition to gravel, sand, silt and shells. The coefficient of permeability of fill layer is estimated to be 1.0 x10-2 cm/s, which is one-order greater than that of the sand layer. Fill layer consists of ancient city ruins of ages respectively from the Eastern Roman Empire, the Byzantine Empire and the Ottoman Empire and has a lot of gaps.The underground part of the Sirkeci station was excavated through a ventilation shaft. Ground surface settlement occurred more than predicted. Therefore, back analyses were performed in order to precisely predict the next-step settlement. However, back analyses with elasto-plastic models could not simulate the actual phenomena and hence, an anisotropic-damage-parameter model developed by Sakurai (1999) was adopted for the back analysis. Furthermore, as the excavation of tunnel proceeded, the ground surface settlement exceeded the predicted value again. Based on the monitoring results, it seemed that pore water pressure decreased by the tunnel excavation resulted in the soft rock and soil to be contracted due to the increase in the effective confining pressure. A coupled hydraulic-mechanical analysis was applied to explain the relationship between decreased pore water pressure and ground surface settlement. The settlement due to drainage from tunnel wall was well-estimated in the coupled hydraulic-mechanical analysis.However, further settlement occurred more than predicted again and again. Though it was very difficult to clarify the reason of the large settlement, it was recognized that the unexpected ground surface settlement resulted from the existence of the large gaps in the fill layer that was greatly compressed. The final settlement reached up to 327 mm."

Jan 1, 2015

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By R. J. Hundermark, K. van der Merwe, L. R. Nelson

Taphole integrity is critical to all furnaces, but it is especially important in high intensity electric furnaces processing matte and metal of high superheat. Key furnace dimensions are the electrode proximity to the taphole, hearth sump below the taphole and the shape and location of the taphole in the furnace wall (e.g., circular versus rectangular furnace). In addition, electric furnace power density needs to be matched appropriately to any configuration to achieve operational reliability and furnace integrity. The role of furnace dimensioning is generically reviewed across many pyrometallurgical processes to explore potential impact on furnace taphole performance. Some empirical furnace dimensions and power density ratios of industrial furnaces are then compared to explore to what extent they may indeed influence taphole integrity.

Jan 1, 2015

By P. E. Georghiou, S. Shafiei Zadeh, H. Hassan Nejad

Data are presented on the extractant behaviour on toxic metal removal from spent hydroprocessing catalyst, produced at the North Atlantic Refinery plant in Newfoundland and Labrador. Aliquat 336 was selected due to its potential capabilities for the separation of cobalt, molybdenum and nickel from the leachate extractant produced by aqua regia. The solvent extraction process was statistically modeled using central composite design (CCD), and the numerical optimization was conducted to achieve the optimum point for toxic metal recovery for the extractant.

Jan 1, 2014

By Alan Bauer, Melvin A. Cook

Measured detonation pressures of "prills and oil" (94/6 ammonium nitrate/fuel oil) and three of the new "slurry" blasting agents are presented and compared with computed, ideal detonation pressures and with detonation pressures expected from the measured detonation velocities. Results seem to show that the peak pressure in the detonation wave in these cases is the Chapman-Jouguet pressure and that no "spike" exists in these detonation waves. The absence of the Zeldovich-von Neumann "spike" is noteworthy in view of the very long reaction zone lengths of these mixtures. The measured detonation pressure of one of the slurry blasting agents (DBA-3") under steel confinement ( 172 kilobars) is shown to be considerably greater than the ideal detonation pressure of 75 per cent gelatin dynamite (p. = 135 kilobars) despite the fact that the detonation was still somewhat non-ideal in "DBA-3," its computed ideal detonation pressure being 180 kb. The popular 94/b AN /FO blasting agent exhibited a detonation pressure of only 13.5 kb in 5" paper tubes, but 37.5 kb in 5"• steel pipe compared with a computed ideal pressure of 40 kb.

Jan 1, 1961

By J. Oyunaa, P. Munkhbaatar, A. Sarnai

"The molybdenum mining process used at Mongolia Erdenet Company is a selective flotation of molybdenite from the copper porphyry ores in which the extraction of molybdenum comes as a byproduct of the ongoing copper production.The mineralogical composition of molybdenum concentrate is 99.4% molybdenite (MoS2), 0.09% molybdenum oxide (MoO3), 0.52% powellite (CaMoO4) and wulfenite (PbMoO4) and content 47.76– 47.92% molybdenum, 1.5–2.67% copper, 0.04% renium.From compared solvents sodium and carbonate and ammonia are like extracted molybdenum than hydrochloric acid, which contained 96.23–97.72 p.c. of its total amount. Hence to take into consideration abundance, cheap and suitable for analysis and processing the molybdenum concentrate ammonia is choosing as a basic solvent. By direct evaporation of ammonia extract solution, we obtained ammonium ortomolybdate, which contains 73.47% MoO3. INTRODUCTIONMolybdenum occurs in the earth’s crust in an abundance of about 10–14%, mainly as molybdenite, MoS2. Small quantities are also associated with other metals having similar chemical properties. Thus wulfenite (PbMoO4) is found in oxidized parts of sulfidic lead deposits in many regions of the world; powellite [Ca(Mo,W)O4] is a calcium molybdate usually formed from the modification of molybdenite in deposits containing tungsten as scheelite (CaWO4) and tungsten substitutes for molybdenum up to about 10%. Ferrimolybdite (Fe2Mo3O12·8H2O) is the product of oxidation of molybdenite in the presence of iron (III) compounds. Molybdenite is the primary source of molybdenum. Should demand for molybdenum rise so that additional sources become necessary, wulfenite, powellite, and ferrimolybdite may become commercially significant. Molybdenum ore is mined by underground and open-pit methods. A typical primary molybdenum ore body contains 0.05–0.25% Mo, and secondary ore bodies (copper porphyry ores) average 0.3–1.6% Cu and 0.01–0.05% Mo. Flotation remains the preferred and almost exclusive method of upgrading the molybdenite mineral to an industrial-grade molybdenite concentrate containing 90–95% MoS2, the balance being gangue (Habashi, 1997)."

Jan 1, 2016

By A. Eltringham

Operations downstream of mining and beneficiation are still being subjected to increasing scrutiny as highly capitalized projects have been either slow to achieve their targets or have actually failed to do so. Leaching and smelting projects have fundamentally high calls on capital and technology as reaction rates are increased and the capture and disposal of unwanted products are subjected to greater restrictions. Separating value from waste inherently becomes riskier as the purification of the desired product imposes greater demands on the process to produce benign wastes. When we superimpose on the chemistry of the project severe predictions of throughput rates, that bring in facets of manufacturing, we are introducing complexities that the records show are not handled well. This paper discusses some of the more common challenges that operators face and what methods are available and are likely to be successful in preventing the loss of value as projects are brought on-stream. This thinking needs to start much earlier and at greater intensity than our industry has normally chosen to employ.

Jan 1, 2011

By Nilce Alves Santos, Vânia Lúcia de Lima Andrade, Keila Lane Carvalho Gonçalves, Harold Wyslouzi1

"When confronted with the difficult decisions on advancing an exploration project to the feasibility and construction stages, it is important to know how various regions of the ore body will react in the milling and concentration processes. While bench scale test work is common and inexpensive, the results and information provided are somewhat limited due to the difficulty in accurately predicting the effects of recirculating middling streams or gradual changes in solution chemistry.Conventional Pilot Plants, processing 100 to 1,000 kg/hour of sample ore, provide the detailed engineering data required to develop a final process flowsheet and to size the equipment. They are, however, expensive to set-up and operate, and are really only viable for major projects that are well advancedIn the latter part of 1999, the Mineral Development Center at CVRD (MDC) purchased a new piece of mineral processing equipment which can run continuous flotation tests using drill core samples. To evaluate its performance, and to compare it with conventional testing methods, various types of flotation tests were carried out using two different types of copper ore. The limitations and advantages of open circuit and locked cycle bench tests, as well as the Mini Pilot Plant and the Conventional Pilot Plant were evaluated.Open circuit tests carried out at the bench scale only provide basic information. More complete and trustworthy information is obtained, in terms of the recirculation of flows and reaching a permanent and stable flotation regime, as the dynamics and complexity of the tests increases. The data obtained showed that the MPP’s metallurgical performance was equivalent to that of a conventional pilot plant."

Jan 1, 2002