Search Documents

By B. Loveday, G. W. Delaney, S. Cummins

"Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage.The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed."

Jan 1, 2012

By S. Kahraman, K. Develi, E. Yasar

Four hydraulic top hammers, one pneumatic top hammer, and three down-the-hole drills were observed in several rock types at quarries and highway construction sites to measure the performance data. At the same time, drill cuttings from each drill hole were collected for the determination of the coarseness index (CI), which is the sum of cumulative weight percentages of a particular size-graded sample of debris, and for the determination of median particle size (MPS), which is defined as the particle for which the quantity of particles equals 50% of the total of the cumulative distribution. After the sieve analysis was carried out on the drill cuttings in the laboratory, CI values were calculated and MPS values were obtained from the plots of cumulative undersize vs particle size. The performance data of the drills, CI values, and MPS values were analyzed using the least square regression method. It was seen that strong linear relationships usually exist between penetration rates and CI values, and penetration rates and MPS values for both top hammer drills and down-the-hole drills. Penetration rates increase linearly when increasing the CI and MPS values.

Jan 1, 2004

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By R. W. Lawrence

"The management of acid rock drainage( ARD) to prevent impact when tailings are disposed of in the environment requires understanding of the phenomena giving rise to acidic drainage, a rigorous evaluation of the weathering characteristics of the tailings, and the successful implementation of control measures that will be effective in the long term. This paper provides a brief theoretical background to the complex reactions taking place in mill tailings containing residual sulfide minerals which must be appreciated to enable waste characterization program to be effective in predicting the future behavior of the tailings and in designing control methods which will work. The principals and practice of prediction and control as part of an ARD management strategy will then be discussed.Paper Not Available at Time of Publication"

Jan 1, 1997

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By Ian Rozier

"Emphasis in recent years in western Canada has been placed on the development of large open-pit coal mines, the most notable developments being in northeast British Columbia. However, vast resources exist below the limit of economic open-pit mining, and with world demand predictions of the late seventies in mind, the potential of underground coal mining in western Canada has been investigated. Particular emphasis has been placed on the Plains coalfield of Alberta, and there is optimism that underground coal mines will be developed in the Lethbridge area of southern Alberta.With no existing operations in southern Alberta with which to compare mining conditions, any mine planning and feasibility level studies rely heavily on the engineering/geotechnical data obtained from surface investigation to predict ground control problems and technical constraints on mining. Such investigations have been integrated with exploration drilling programs. Emphasis has been placed on extracting maximum information to provide an over-all appreciation of potential ground conditions and to identify specific ground control problems that could be encountered.The acquired geotechnical parameters are then used to evaluate the mine properties from an engineering standpoint for input into the determination of optimum mine layouts, development directions, mining methods and roadway and face support requirements. These geotechnical studies have been primarily directed toward the longwall mining method, but the acquired data base could equally be applied to alternative mining methods.In addition to the lithologic and structural controls which relate to roof stability, caving characteristics, floor heave and subsidence, investigations have been directed at gaining an understanding of the over-all surface and ground water regime with respect to potential inflow into the mine openings and ground control problems that could be caused by inflows encountered during mining. Experience has shown that soft floor conditions and water control are important factors to be considered in a longwall layout, and without doubt these parameters will play a major role in the design and operation of a successful longwall operation in the Lethbridge coalfield."

Jan 1, 1986

By B. Misra, B. S: Sastry, Kollu S. Rao

"This paper reports the results of a finite element study of the geothermal heatflow into dry mine airways. For isotropic and unsteady state conditions the heatflow into mine airways is studied for a range of surface heat transfer coefficients between rock and air, and age of the airway. Dimensionless temperature gradient values are presented in tables for different values of Boit and Fourier numbers and the results are compared with Starfield tables and Gibson algorithm. It is found that Starfield tables have consistently over-predicted the G values with errors ranging from 2% to 10%. The differences between results obtained from the finite element study and the G values calculated from Gibson's approximation method are mapped. The small error values over a large range of Fourier and Biot numbers confirm the suitability of Gibson's algorithm to rapidly calculate G values for estimating the heat transfer from surrounding rock to mine air.IntroductionIn many underground mines heat is a major problem, and the provision of acceptable working conditions requires considerable expenditure on ventilation systems. The rational design and operation of these systems depend upon an understanding of the various sources of heat in the mine. The natural source, i.e. geothermal heat, contributes up to 80% of total heat added to mine air and it is difficult to analyze and predict the heat owing to a number of influencing variables. The problem of geothermal heat flow has been studied by many investigators (Goch, 1940; Starfield, 1966; Hemp, 1987; Amano et al., 1982; McPherson, 1986).The primary concern of this paper is to develop a better ready reference dimensionless transient temperature table for estimating heatflow at any stage of mine airway life."

Jan 1, 1994

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By Schoeman L., K. C. Sole

Evaluation and measurement of the influence of changes in conditions and electrolyte composition during early stages of a growing metal electrodeposit are crucial to predict changes in developing morphology. A galvanodynamic polarization technique was developed to reliably measure overpotentials for nickel electrodeposition from sulfate electrolyte. The validity of these polarization parameters as indicators of the relationships between changes in the electrolyte and resulting deposit morphology was evaluated for electrolytes of varying composition. Findings indicate that nucleation and plating overpotentials measured by the described technique can be used as indicative tools for monitoring, evaluating and ultimately improving control of the electrodeposition of nickel from sulfate electrolytes. The results predict that nickel deposits of desirable quality and morphology are obtained when plating overpotentials are higher than 700 mV vs. Ag/AgCl and nucleation overpotential is less negative than plating overpotential.

Jan 1, 2017

By Yuki Tsunazawa, Sho Fukui, Chiharu Tokoro

"A milling process is one of the important unit processes in mineral processing. In the milling process, the control of particle size distribution is necessary for the later physical separation process. Since the milling process is strongly affected by the equipment designs, operation conditions and raw materials, the control for particle size distribution of milling products is mainly based on empirical rules. Recently, the discrete element method (DEM) has been widely used as an effective tool to investigate the behavior of grinding media. Although the behavior of grinding media can be accurately simulated, it is not well-established the way to predict particle size distribution after milling by the DEM simulation.The objective of this study was to develop a new method to predict particle size distribution in ball milling using the DEM simulation. To predict particle size reduction, a correlation between experiments and the simulation was investigated in various operation conditions, that is, wide range of the rotation speed and the filling ratio of grinding media. In experiments, after lime stone was ground, the average and variance of particle size distribution were evaluated using some kinds of distribution equations. In the DEM simulation, direct simulation of particle disintegration in milling process is generally very difficult because of huge computational load. Therefore, collision energy between grinding media balls orgrinding media ball and wall was used as a factor of particle disintegration.As a result, a good correlation between experiments and simulation was obtained. In addition, the particle size distribution in ball milling could be predicted using this correlation. Therefore, these results indicated that the use of the correlation between experiments and the DEM simulation was an effective approach of predicting the particle size distribution in milling process."

Jan 1, 2016

By J. H. Nantel, J. F. Archibald

"The presence of radon from uranium-bearing ores, waste and from backfill material introduced underground to provide ground support, work platform and waste disposal functions, requires that ventilation controls be established to maintain safe working level concentrations. One approach has been developed at Queen's University to quantify radon and radon daughter source level s and to estimate ventilation requirements necessary to maintain these safe levels.Knowledge concerning the sources of radioactive contaminants and their production quantities is of value for planning and design stages of ventilation control systems. For any given mine layout, radiation level estimates may be forecast and modified by ventilation network design where excessive production quantities may exist.Behaviour of Radon Gas in MinesRadon gas, produced from the decay of Ra-226 in a host medium, will diffuse through porous media. In areas adjacent to mine workings, radon will be liberated into the mine atmosphere. The rate of radon emanation is proportional to the rate at which radon is produced within the host material (a function of the ore grade of U308) , to the radon concentration gradient in the host pores and to the diffusion properties of the material.The radon source concentration is determined by the rate at which Rn-222 is produced by the decay of Ra-226, and by the emanating coefficient (E), or fraction of the radon which escapes from the source matrix and is free to diffuse through the pore spaces."

Jan 1, 1984

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By M. Fooladi Mahani, M. R. Izadpanah

The knowledge of the thermal shock resistance of refractory materials is of outmost importance due to their wide range of applications in various industries, namely; ceramics, oil refinery, thermal insulation, nuclear power, chemical and petrochemical industries. Thermal shock resistance is measured in terms of the number of cycles that a refractory material can withstand when subjected to sudden temperature changes. This property is measured experimentally by heating a sample of the material and cooling it in a known environment then the number of cycles it withstands this treatment without spalling is a measure of its thermal shock resistance. Although this method of experimentation has long been the practice, but it is both expensive and time consuming. Various studies have been carried out to predict this vital property, however, the rang of applications are limited. The present study employs a test rig by which temperature distributions in magnesite samples are accurately measured. This information plus other results obtained from relevant tests on related properties are used to develop a model which predicts the number of quench cycles withstand by different materials when subjected to sudden temperature changes. The comparison of the theoretical values using the solution of the presented model with experimental data for different materials having different thermal resistance shows a closed agreement.

Jan 1, 2004

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By Quin Dennis

Process Optimization ?What is it really? It is NOT ?a larger fan to increase draft through a process ?a larger pump on a wet circuit ?a wider conveyor belt for solid materials ?a larger feed elevator into or out of a process These relieve individual constraints ??bottlenecks??and allow operation to the next constraint in the process ?It is also NOT about automating the operator ?which captures consistency but is not continuous optimization

Nov 1, 2011

By Gwenaële Petit, Ulan Massimkhanov, Gilles Joubert

For its Zuuvch Ovoo uranium deposit in Mongolia, Badrakh Energy (partly owned by Orano Mining) is working on the prefeasibility study for exploitation by ISR (in situ recovery). As part of this project, Orano built a 2-cell (each cell is constituted of one producer well located in the center and surrounded by six injection wells in an hexagonal pattern) and a processing pilot plant that will be used to demonstrate the operability and economic viability of an ISR process. Another main objective of this pilot trial is to demonstrate the ability of Orano’s modeling tools to predict the ore behavior under given leaching conditions. To model uranium production by ISR, Orano uses HYTEC, a reactive transport computational software, which was adapted for its existing operation in Kazakhstan (Katco) to predict uranium recovery and reagent usage based on operating conditions. In order to perform similar simulations for this new deposit, Orano engaged in a comprehensive program including ore sampling, detailed characterization, and metallurgical testwork. The mineralogical conclusions were used to prepare a simplified geochemistry for the ore, in particular carbonate and reactive clay grades, uranium mineralization and penalizing elements such as pyrite. Then, bottle roll leach tests were used to characterize dissolution kinetics for smectite clays. Eventually, column leach test results such as pH, free acid, and uranium recovery were modeled on HYTEC to improve the fit of some of the dissolution kinetic parameters. Parameters fitted using metallurgical test work results will now be used as inputs for predictive model at the pilot scale, in order to anticipate operational results and help with operating decisions for production ramp up.

Jan 1, 2020

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019

By M. J. Sapko, R. W. Watson, E. S. Weiss

The relative incerdivity of several blasting agents was evaluated in the Bureau's Bruceton Experimental Mine (BEM) . The minimum charge weights resulting in the ignition of predispersed oil shale dust clouds were measured for each of the explosives. A 400 g unstennned charge of ANFO (ammonium nitrate-fuel oil) was sufficient to initiate an oil shale dust explosion, whereas a 1000 g unstenuned charge of an emulsion blend did not ignite the dust even with the addition of 4% methane gas. Several stenuning materials were evaluated in the BEM for their effectiveness in preventing the ignition of near stoichiometric methane-air mixtures. Water stenuning was superior to all other inhibitors tested against methane. Explosibility testing of fine sulfide ore dust in a 20 L chamber and in the BEM show that the dust is capable of propagating an explosion given nominal concentrations of 700 to 800 g/m3. Results are encouraging and irrlicate that there is merit in pursuing explosive composition as a means of reducing ignition probability of oil shale and sulfide dust clouds generated during nonnal blasting operations. The proper selection of explosives and stenuning materials should significantly reduce the probability of secondacy dust explosions in oil shale and sulfide ore mining.

May 11, 1988