Search Documents

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By C. Barnett

"A description of the Geco orebody has been given by W .L. Brown and R.C.E. Bray (1). The mill flowsheet and equipment were described by M.J.S. Bennett, D. Wild and C. Lawton (2). Mill capacity is now 4, 150 tons per operating day of copper, silver, zinc and lead ore. A recent flowsheet has been published in the - Canadian Mining Manual (1966).Soon after the start of production in September 1957, it became apparent that large tonnages of sand would be required by the mine for backfill pruposes. Initial experimental work on the preparation of sand fill from the flotation tailings was begun in late 19 59. Cyclones of local manufacture, in a variety of sizes, were tested quite successfully. There were, however, several obvious advantages with some of the custom-built cyclones and a recommendation was obtained from the Techniquip Company. A single Krebs D-10-B cyclone was tested experimentally in 1960.INITIAL TESTWORKExperimental results showed that with our relatively coarse grind (in the order of 53 % minus 200 mesh) 75 - 80% of the flotation tailings could be recovered as backfill sand with one stage of treatment. Percolation rates of four inches per hour were obtained with cyclone inlet pressures in the range of 20 - 25 psi and feed densities of 20 - 23% solids."

Jan 1, 1968

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

By Jun Shan

The preparation of poly(N-isopropylacrylamide)-monolayer-protected clusters (PNIPAM-MPC) of gold nanoparticles was carried out in a homogeneous phase using three ways, in which three types of PNIPAM ligands were employed. The first type comprised of PNIPAMs with narrow molar mass distributions, synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and thus, bearing a dithiobenzoate at the chain end. These polymers were used directly to passivate the gold nanoparticles upon the Schiffrin reaction in a one-pot synthesis. The second type of ligands was derived from the first one through hydrazinolysis, and they therefore contained a thiol end group. The third type of ligands was PNIPAMs obtained through conventional radical polymerization, post-modified to contain thiol end groups. The PNIPAM-MPCs were characterized by high-resolution transmission electron microscopy, and by dynamic light scattering. The one-pot synthesis utilizing the ligands of the first type turned out to be a simple and facile method, compared with the other two ways, with which the size of the gold nanoparticles can be easily manipulated mainly by adjusting the molar ratios of PNIPAM / HAuCl4. PNIPAM is a more efficient ligand to stabilize the gold nanoparticles in water and in organic solvents than alkanethiols. The surface density of PNIPAM chains ranged from 1.8 to 3.6 chain/nm2, which is much lower than that typical for alkanethiols. The thickness of a PNIPAM monolayer bound to the gold core is somewhat larger than the size of the random coil of corresponding free PNIPAM in aqueous solution, which suggests that the conformation of a PNIPAM chain bound to the gold core is to extended.

Oct 1, 2003

By Hyung Sup Choi

The preparation of high-purity zirconyl compounds was studied in order to develop an economical process for obtaining pure zirconium via the caustic fritting of zircon sand. The direct dissolution of caustic frits with concentrated hydrochloric or nitric acid at 80c. followed by the addition of a small amount of acidified gelatin, gave high-purity zirconyl chloride or nitrate. The addition of a small amount of gelatin caused a mutual flocculation between colloidal silica and gelatin. The precipitation of this silica floc markedly lowered the content of silica in the product. The silica content of the compounds (or solution) so produced, generally less than 100 ppm., was sufficiently low for tributyl phosphate extraction for nitrate solutions. It was found that the degree of purification de-pends not only on the procedures employed but also on the nature of the frit itself. Silica was more effectively eliminated from the fritted product produced at higher temperatures, and less silica was present in the com-pound prepared from the frit produced in a shorter heating time. In order to ascertain the nature of the

Jan 1, 1965

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By Glen A. White

The level of impact and mitigating measures that are forecast in an environmental assessment (EA) for a new, or significantly modified, metallurgical processing facility or mine are taking on increasing importance during the subsequent life of the facility. The basic premise is that one is authorized to operate within the envelope defined by the approved EA. Operations inevitably change as they develop and mature, and at some point, one is faced with the prospect of re-doing the original EA work. This can lead to significant development delays. Cameco Corporation (Cameco) has played a major role in developing the northern Saskatchewan uranium mining industry over the past decade. Through the EA process, the company has developed ideas on what works well in generating approvals that give the operator some future flexibility. Early introduction of concepts for potentially different mining and processing methods, as well as contingency plans if things do not work out exactly as predicted in the original EA, can make subsequent regulatory approval for change a more efficient process. One must also preserve the principles of open consultation upon which the EA process was originally based. As such, involvement and support from local communities and other stakeholders is required to ensure the long-term success of the EA process.

May 1, 2004

By Jennifer Pakula

Productivity improvements in underground mining are becoming harder to find. Most mines quickly identify deficiencies in their processes and then struggle to make productivity gains beyond that plateau. One way to increase productivity in this situation is to modify existing methods of operation. Vale?s Stobie Mine has been in operation since the late 1800?s employing a variety of mining methods. Many mining advances have been incorporated over time. With the advent of mechanized rubber tired equipment, sublevel cave mining was introduced to allow economic extraction of a large low grade area. Additional productivity gains were seen in the sublevel cave area with the introduction of preloading production drill holes. In preloading, the holes are loaded with bulk emulsion ahead of the production cycle and then primed for blasting as needed. The introduction of preloading, although giving the Stobie sublevel cave process an overall productivity gain, saw an increase in oversize due to the collar priming technique employed. Handling oversize material prohibited the operators from handling additional units of optimally sized material. Prepriming, adding detonators at the toe and midcolumn of the production holes during the preloading process, was identified as a change that could reduce the formation of oversize. This paper describes the introduction of prepriming to the sublevel cave mining method and focuses on the process Stobie employees followed to ensure a safe transition to this productivity improvement.

Nov 1, 2011

By D. Mark Richards

Highland Valley Copper (HVC) is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using GPS has been utilized at the mine since 1996 for blast hole drill navigation and since 2000 for shovel and dozer navigation. Since 1997, rock recognition has been part of the drilling process. This allowed the mine to develop a Mine to Mill strategy using the rock hardness information from drill monitoring systems to both refine drilling and blasting parameters as well as downstream crushing and grinding strategies. Although this preliminary effort has been very successful at HVC, the current intent is to gain further benefits through better use of existing information while also deriving an enhanced data set from monitoring production drills. In the latter case, the objective is to acquire and process drill variables in such a manner as to permit more detailed definition of rock mass characteristics. The subsequent focus will be to use the derived geotechnical and geological information as part of a practical process to more prescriptively blast the rock mass. Through the definition of domains based on drill monitored derived rock mass properties, the intent will be to enhance blast outcomes that lead to optimized downstream (from blasting through to concentration) processes in a more proactive and timely manner. This paper examines a proposed approach to be able to derive more accurate and consistent rock mass properties from production drilling. In addition, the discussion will identify potential benefits to be gained from process improvements that result in enhanced productivities, and crushing and grinding optimisation due to blasting strategies that are more closely matched to identify rock mass characteristics.

May 1, 2007

By D. Bernard

Over the last decades, the wrought aluminum casting industry has made significant progress with regards to process consistency by the introduction of new technologies in the field of liquid metal processing and casting. These technologies, combined with the application of best practices, have led to increases in productivity as well as better process performances and product quality. The competition in the addedvalue aluminum products (by opposition to P1020 production) is, however, very strong and involves players that did not hold a major role five years ago but who are now exerting a strong competitive pressure on our industry even sometimes from far abroad. There are still technical and technological challenges remaining in the different areas of aluminum casting production, amongst which metal pre-treatment, furnace operations, in-line treatment and casting hold a predominant influence. The comprehension of the contribution of each individual process step to the entire process chain is a key element and must be considered in future process optimisations. This paper presents the technological position of the casting industry and tries to highlight areas where further progress can be made.

Jan 1, 2006

By Steve Scott

Green Economy Toyota Prius Hybrid contains about 50 kg of copper. All-electric cars have about 100 kg of copper. From where will all the copper come? Wind turbines have 1 metric ton of copper China is building 221 cities of 1 million people by 2025 (13 cities per year from 2008) = 10 New Yorks. The Greater Toronto Area has 5.6 million people, so a new GTA every 22 weeks!

May 1, 2013

By C. M. Kleemann

The paper describes the present milling practice at Western Mining Corporation Limited's new nickel mine at Kambalda in Western Australia. It details the crushing, autogenous grinding, flotation and spray drying circuits for the production of a nickel concentrate. It also indicates some of the metallurgical problems which have been encountered in concentrating this ore.

Jan 1, 1973

By Donald L. Mordell

Introduction A very large part of the world's fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

By A. W. Lovett

"THE last two years have been years of recession or, perhaps, years of marking time, depending upon whether the observer is a pessimist or an optimist. There has been a slackening in the industrial tempo that has been reflected in many ways in the national economy. As one of the chief barometers of economic health, the consumption and supply of energy reflect this slowing up.These same two years have also seen significant changes in the relation between the sources of energy. In periods of declining demand, it has happened in the past that coal, as the basic or residual source of energy, has shown the effects to a greater extent than the other energies. In these two years, however, in addition to this usual effect, there has been the acceleration in the Joss of market to diesels in the railway consumption category and the continuing decline in domestic consumption. The story of these years is presented in the statistical tables that form the foundation of this paper. Statistics, particularly in the form of tables, are rather dry and are sometimes difficult to follow but the overall developments are illustrated by graphs which present a more striking picture."

Jan 1, 1959

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By K. Thuro, H. Käsling, F. Menschik

"With increasing data volume, due to enhancing requirements for ground investigation programs for large construction projects, the demand for more efficient filing systems is more and more growing. Depending on the project we also have to use flexible systems to cope with varying data out of different lab and field tests.The chair for Engineering Geology at TUM is developing a web-based database solution to handle all project relevant data in a more appropriate way. We aim to optimize our data management to achieve a fast and easy way of collecting, documenting and analyzing our gained data. The second objective is to provide an easy access to our data for project partners across broadly distributed locations.This Database system consists of a PHP web interface and a MySQL database core. The current setup allows an online access via Internet (www). We are able to grant and constrain access to all data or only arrays of data with our user management system to guarantee the safety of project data and respect all rights and proprietorship. The database system is of modular design and consists of the following three base modules: module of general project data, module of laboratory data and user management module. At the current stage we are able to save and work with all usually generated specific values from unconfined compressive strength tests, brazilian tensile strength tests, point load tests, CERCHAR and LCPC abrasivity tests and ultrasonic tests. The user is able to perform a simple statistical analysis within our database (e.g. average calculation of one sample) and export data as csv or xls files for further analysis.For specific questions within projects we are able to deploy and integrate further modules in our database system. At this moment, we are developing an add on to use this database for different drill test analyses. One of the tools correlates drilling performance and drill head wear measured in the field with rock mechanical properties, and extrapolates the data to estimate the performance and wear in new projects. Today we are managing 90 projects with 550 samples and almost 1350 lab tests with the base module.In our contribution we aim to demonstrate an efficient way of data structuring using a relational database for laboratory and field testing data."

Jan 1, 2015

By Norman R. Ball

"Many people in the mining and metallurgical industries were brought up to embrace Henry Ford's pronouncement that ""History is bunk"" but it is not generally known that the same Henry Ford created and paid for one of the finest technological museums in the Western World. I am aware that many people feel that industry history is something you ask aging executives to do or that history is a clip-andpaste compendium of pictures re-discovered every 25 years or on the occasion of issuing a press release on plant expansion. Moreover, there are many who fear historians as somewhat deranged individuals interested only in corruption, injustice and sensational labour strife. Good history lies somewhere between the controlled P.R. handout and the hysterical attack. Writing good history is a difficult creative act based on the application of experience, insight, wide knowledge and careful reasoning to available evidence. To date, the Canadian mining and metallurgical industries have achieved a great deal but left too little evidence and it is this lack of evidence which must be corrected before it is too late. It is the purpose of this article to stimulate thoughts with regard to archives, one of the more important vehicles for the preservation of such evidence."

Jan 1, 1999

By S. A. Willis

For the past several months 1 have been considering the functions of this Society and its reasons for continuance. The fact that it is now sixty years old indicates that it must have been of value and we all know that it has contributed much that was worthwhile to Nova Scotia and the Maritime Provinces. The question arises: "What is the future of the Society, and how might its activities be altered to suit present-day activities and to be of even greater value?" Let us analyse the various activities in which we are interested and determine which, if any, are of more value than others. First of all, at least once a year we have a two-day convention which constitutes a holiday for the members and their wives. This has always been well planned and has been much enjoyed. Second, there are many social and business contacts made during the meetings and interim meetings. These certainly tend toward better relations and co-operation between the various people concerned. Mine operators meet other mine operators, engineers, people from the education fields, Department of Mines, and so forth. Various sales contacts are made at these meetings which can be of value and use to both the Company selling and the customer. Third, and of greatest importance in any conference, is the exchange of ideas by the members and by authorities from outside, and the presentation of slides and drawings, or actual visits to operations. It is upon this phase that 1 wish to elaborate. These papers are not only presented to our meetings but are generally published in the C.I.M. Bulletin so that members throughout the Dominion have access to them. Many important papers describing new phases of operations have originated through our Society.

Jan 1, 1947