Search Documents

By D. B. Smith

DURING the summer of 1953, test work commenced at the Sullivan Concentrator with a view to the modification of filtration practice by the inclusion of wet cyclone classification of the lead concentrates, with separate filtration of the underflow and overflow products. Formerly, practice was conventional and the equipment employed comprised one 50-foot diameter thickener ?with the underflow routed via a 20-foot stock tank to two 8-foot by 12-foot Oliver filters. Heating of the filter feeds to 40° C. and the use of mechanical slappers on the filter drums ?have both been standard features of Sullivan practice for years. Both of these have been retained. Currently (February, 1956), lead concentrates are being classified into sands and slimes by 12-inch cyclones with the underflow, at 75 per cent solids, being fed to No. 1 Oliver filter. The overflow is thickened to 75 per cent solids and filtered separately by a No. 2 Oliver filter . The tonnage split is approximately two of underflow to one of overflow. The overflow contains 75 to 80 per cent of the total minus I 500 mesh slimes in the feed.

Jan 1, 1956

By R. A. Elliott

This paper describes the development of an infra-red ore dryer at the Mines Branch. The dryer utilizes an infra-red heat source mounted over a stainless-steel belt to dry ores and concentrates of varying particle size and moisture content. It has been found to ?be successful in meeting Mines Branch requirements of minimum dusting loss and ease of cleaning to decrease ,contamination between various batches of dried products. It is described with the hope that it might .prove useful in other laboratories where there are similar problems. It might have an application in the drying of concentrates containing high values where dust losses would result in a considerable loss of revenue; also for small batches of material or an intermittent drying problem.

Jan 1, 1958

By D. McConchie

BauxsolTM, prepared by treating bauxite refinery residues with Mg2+ and Ca2+, has an excellent ability to remove arsenic from acidic waters. The addition of BauxsolTM to sulphidic waste rock at the Gilt Edge Mine, South Dakota, reduced As concentrations in leachate water from 35 mg/L to < 0.005 mg/L; the concentrations have remained below 0.005 mg/L for the five years since the treatment was initiated. However, ordinary BauxsolTM does not effectively remove As from near-neutral water and it needs to be acid-treated or blended with small amounts of reagents, such as jarosite or ferrous sulphate, to increase the proportion of positively charged binding sites on the particles. The use of a jarosite/BauxsolTM blend can effectively treat ponded water, and As(V) concentrations can easily be reduced from over 1 mg/L to < 0.001 mg/L; As(III) has to be oxidised to As(V) for effective removal. Metal contaminants in the jarosite are trapped by the BauxsolTM and only very small amounts of the As, or other elements bound during treatment, are liberated using a TCLP leaching test. The exhausted treatment reagents meet the criteria for classification as an inert solid and do not need to be disposed of in a secure repository.

Jan 1, 2006

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By K. U. Kainer

Magnesium and its alloys as the lightest available construction metal offer a wide range of opportunities for the usage in transportation industries, especially Magnesium wrought alloys with their improved mechanical properties show a high potential for structural applications, While magnesium cast components have found their application the interest is now spreading to wrought alloys due to the possibility to get even more homogeneous and better properties compared to cast parts, Therefore alloy and process development especially for extruded and sheet material is a main concern to enhance the application of Magnesium wrought alloys, Castings are still form the majority of applications of magnesium alloys, although efforts to develop adequate wrought alloys have increased, In the presentation, the alloy requirements for processing of cast and wrought alloys will be discussed, The various processing routes and alloy compositions result in specific microstructures and properties which determine the potential use of these alloys, Today, the spectrum of available alloys covers standard alloys as well as alloys for use at elevated temperatures, The trend will be to further diversify the alloy compositions and to improve the alloy properties, Areas of concern still remain the wrought processing and the high temperature (creep) and corrosion properties of magnesium alloys, Examples of recent developments in these sectors will be given, The presentation will also provide an overview of the historical and current use of magnesium and an outlook on future applications.

Jan 1, 2006

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By L. V. Chugaev, Y. M. Shneerson, P. V. Zaytsev, I. V. Fomenko, M. A. Pleshkov

"Pressure oxidation (POX) is one of the most common and reliable methods of processing gold-bearing sulfide concentrates. However, when processing concentrates that contain natural carbonaceous matter, substantial gold losses occur due to autoclave preg-robbing. The latter involves formation of gold chloride complexes under typical POX conditions (high temperatures, high acidity and high ORP) and subsequent sorption of these complexes by carbonaceous matter. Naturally, chloride ion plays a significant role in the process of autoclave preg-robbing; its concentration in POX solution has a well-marked effect on subsequent gold recovery during cyanidation of POX residue. The previous research done by SRC Hydrometallurgy showed that autoclave preg-robbing of gold could be significantly inhibited by the addition of mercury(II) compounds to POX slurry. The positive effect of mercury(II) was well pronounced both at high (>20 mg/L) and low (<5 mg/L) Cl concentrations in POX solution. The successful bench-scale laboratory testing was followed by pilot plant trials at Ore Test Facility in Blagoveshchensk, Russia. The present paper provides the results of these trials. The bench-scale testing results were verified; the optimum oxidizing parameters and reagent dosage were specified. The behavior of mercury (II) at POX pilot plant was found to be in good consistency with industrial practice described in the literature.INTRODUCTION Pressure oxidation (POX) is one of the most common, reliable, and commercially proven methods of processing gold-bearing sulfide ores and concentrates. However, when processing double refractory materials that contain natural carbonaceous matter, POX technology advantages are compromised by autoclave preg-robbing of gold. The latter occurs when natural organic carbon and soluble halides are both present in autoclave feed. Strongly oxidizing conditions of POX (high temperature, oxidation-reduction potential or ORP, and acidity) favor formation of gold-halide (mostly, gold-chloride) complexes, which tend to bond with carbonaceous matter. The exact nature and mechanism of this bonding is unknown, but as the result of this, cyanide is unable to leach gold from POX residue and the precious metal is lost to the tails (Axenov et al., 2014; Dimov, Chryssoulis, & Sodhi, 2003; Fomenko, Zaytsev, Pleshkov, Chugaev, & Shneerson, 2013)."

Jan 1, 2017

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By Mark Richards

Highland Valley Copper is a large, open-pit copper mine in the southern interior of British Columbia. Reclamation has been in progress on the site since 1987. Some 6,300 hectares will have been disturbed at the end of the mine?s life, the majority of which will eventually be reclaimed. The establishment of vegetation and the development of a self-sustaining vegetative cover are the central components of the mine?s reclamation plan. The present vegetation-monitoring program for the reclaimed area represents a significant commitment of resources and only addresses a small portion of the site each year. In an effort to expand the area surveyed while improving the efficiency of the monitoring, the use of remote sensing is being investigated. Airborne multispectral imagery was acquired in the summer of 2001, and the results of the multispectral classification were compared to ground observations made during the routine 2000 and 2001 monitoring program. A thematic map with 17 vegetation classes was produced. Within the vegetation classes, there was a strong spectral separation between ? dry grasses? and ?legumes? with further separation according to their density. Green biomass could also be quantified remotely across a wide variety of vegetation types. During summer 2002, further aerial imagery was acquired in combination with a targeted ground-truthing program to determine characteristic vegetation types associated with recognized spectral signatures, which can be used in a supervised classification. It is anticipated that after some fine-tuning, it will be possible to shift the ground-sampling effort from areas where the aerial classification confidence is high to more complex areas.

May 1, 2003

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By H. E. Grier, H. H. Aronson, H. F. Coffer

"Nuclear explosions are currently being planned for use in oil and gas production, the recovery of oil from oil shale, gas storage and copper leaching. The current status of each of these projects is discussed, with emphasis on the economics of each application. The first commercial application of nuclear explosives will be in gas stimulation. Project Gasbuggy will be rapidly followed by two additional shots, also related to gas production. These three events, each in a different formation, will be described in this paper with a discussion on their significance to the world's oil and gas industry. The use of nuclear explosives in oil and gas stimulation should be a standard accepted practice within a few years. Calculations based on explosions in media such as tuff, alluvium, granite and dolomite predict large increases in productivity when nuclear devices are used in tight, thick formations. The broken-up rock resulting from the explosion becomes the new well bore, with a production rate of six to twelve times that of a normally completed well.Also included in the paper is a discussion of the real or possible problems associated with nuclear explosive engineering. The only major foreseeable problem is the seismic shock wave. This limits the size of explosive which can be used near important surface structures. A discussion is included on the radiation problem, which we believe to be largely psychological in the case of contained explosions."

Jan 1, 1968

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By Gordan Marrs, O. Matwijenko

"The Kidd Creek metallurgical site has been highly integrated to maximize revenues from its base metals mines. The site's operations include a Concentrator processing 4.3 million tonnes per year of copper-zinc ore, a Copper complex producing 100,000 tonnes per year copper cathode and a Zinc Plant producing 130,000 tonnes per year of zinc metal. To improve operating efficiency with increasing emphasis on productivity, process control, process automation and process optimization have been augmented and expanded during the last decade.New microprocessor based control systems provided the opportunity for the capturing of an expanded number of process related measurements. As supervisory computers were already in place, databases could be generated with only increased disc space and database management programs required. Once the data had been accumulated and stored, a method was then required for handling, screening and sorting large volumes of information in relatively quick and easy terms in order that the stored information could be used. By 1984, a decision to use personal computers for accounting, engineering and management reporting provided the vehicle necessary to handle this data. Using commercially available software, large volumes of stored process data can be downloaded from existing databases, filtered, sorted, analyzed, graphed, displayed, projected, reported and distributed. All this can be performed in very little time."

Jan 1, 1989

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such &apos;bootlegs&apos; are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

By Randy Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Occasionally mine operators are unaware of the presence of free gold particles in their ores because they have not seen free gold hand specimens or at the working face of the mine.Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment. The trapping and subsequent release of gold particles can frustrate attempts to calculate accurate metallurgical balances.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1997, 1998, 1999 and Walsh, 1986, 1992). In 1995, the author used radiotracers to locate and eliminate gold traps at La Mine Doyon (Clarkson, 1997). In 1998 and 2001, the author also salted mineral processing circuits at Royal Oak's Pamour Mine in Timmins (Clarkson, 1999) and at Gold Corp’s Red Lake Mine in Ontario with radioactive gold particles.The gamma and X-ray radiation from gold's nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment with scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps, improving security, determining the recovery efficiency of Knelson gold concentrators and estimating retention times of gold particles in various processes."

Jan 1, 2003

By R. Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as an inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1995; Walsh and Rao, 1986; Walsh and Kelly, 1992). In November, 1993, the author inspected the grinding circuit at La Mine Doyon in Rouyn-Noranda, Quebec and made recommendations to recover coarse gold and to eliminate gold traps from the circuit. In 1995, the author salted mineral processing circuits with radioactive gold particles. The gamma and X-ray radiation from gold’s nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment using scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps and improving security.Nuclear TracersWhen particles of gold are placed in a nuclear reactor, some of the gold atoms (Au197) absorb another neutron in their nucleus to form gold’s radioactive isotope (Au198). In the process of radioactive decay, this isotope emits high energy gamma rays and X-rays which are easily detected (even through steel) with scintillometers.Radioactive gold (Au198) has a very short halflife of 2.7 days. At the relatively low activity levels used for tracing, the particles remain detectable with a small hand-held scintillometer for about 10 to 14 days. After 14 days the irradiated gold is close to background levels and within two months it is essentially non-radioactive. The radiation has no effect on the recovery characteristics of the gold particles. The gold radiotracers are very safe due to their very low level of radiation, short half-life, and their inherent physical and chemical stability. However, the use and possession of even mildly irradiated gold is strictly licensed and regulated."

Jan 1, 1997

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979