Search Documents

By Z. Q. Liu, J. M. Du

"On the basis of analyzing current design and applications, the structure form, working loads and design principles of shaft sinking headframe are summarized in this paper. To overcome the insufficient bearing capacity and geometry size of the finalized shaft sinking headframe in China, a series of new large shaft sinking headframe were developed under vertical shaft construction conditions of maximum net diameter of 12.0 m and maximum depth of 1200 m. The new series shaft sinking headframe include two sets (with single sheave platform and double sheave platform), three dimensions (optimum shaft diameter <8.0 m, 8.0-10.0 m, and 10.0-12.0 m, respectively) for each set, and has innovation and optimization on structure of the sheave wheel platform (MU type) and bracing frame (REN and ZHONG type). The largest new shaft sinking headframe can arrange up to 4 hoisting equipment simultaneously and has bearing capacity more than 10000 kN. Two of the new shaft sinking headframe were successfully applied in practical engineering, such as the Hulusu auxiliary shaft, the Dahaize 1# auxiliary shaftand Sishanling auxiliary shaft. These applications showed that the new shaft sinking headframe has sufficient bearing capacity and reliable applicability. The new shaft sinking headframe could provide an effective guarantee for safety and efficiency sinking of deep-large shaft in the future.INTRODUCTIONShaft sinking headframe is one of the basic shaft sinking structures and it is mainly for hanging hoisting containers and sinking facilities in sinking a vertical shaft (Yu & Shi, 1991; Wang, Jing, & Liu, 2007). Currently, 7 types of steel pipe sinking headframe are used in China, which are mainly finalized by the Ministry of Coal Industry of China (Wang, 1988). As shown in Table 1, V-type is the largest of them and it is only suitable for sinking shaft of diameter less than 8 m and depth less than 1 000 m(Yang, 1982). However, with the increase of mining depth and scale of mineral resources in China, the diameter and depth of newly built vertical shaft are increasing continuously (Xie, Zhou, Xue, Wang, Zhang, & Gao, 2012; Qi & Pu, 2013). At present, the maximum net diameter of vertical shaft is close to 12 m, and the maximum depth is more than 1600 m (Yang & Chen, 2015; Xu, Yang, Liu, & Qin, 2015). The shaft sinking headframe has become the main restrictive factor for the development of sinking equipment, such as the height of muck discharging platform cannot meet the usage requirement of hydraulic umbrella driller, the size of sheave wheel platform is difficult to arrange the increasing hoisting and suspension equipment, the bearing capacity is insufficient to meet the needs of multiple hoisting loads in sinking a deep-large shaft, etc. Therefore, development of new shaft sinking headframe for deep-large shaft (>1000 m in depth and 8~12 m in diameter) is urgently required for China and also the whole world."

Jan 1, 2019

By J. Poplawski

In mineral processing plants, cyclones typically perform the classification duty prior to the downstream recovery process. Particle size distribution of the cyclone overflow is an important parameter and can be viewed as the product of the comminution process. Too coarse of a product will likely have poorly liberated valuable minerals and make recovery difficult. Too fine of a product may represent a missed opportunity to increase plant throughput and/or also result in low recovery due to poor kinetics. “Near-line” particle size measurement instrumentation has been in place for several decades, its availability and low measurement frequency have typically been inadequate for reliable use in automatic control. CiDRA Minerals Processing has developed a novel and robust technology that provides a highly reliable and low maintenance system for “on-line” measurement of the particle size in the overflow of individual cyclones. The system is based around a wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter. The system does not require sampling and associated sample transfer piping that is prone to plugging, thus avoiding high maintenance requirements. Plant data and benefits realized from the latest installations of the CYCLONEtrac PST will be presented. INTRODUCTION Impact-based real-time hydrocyclone particle size measurement Acoustic impact-based particle size tracking is a unique method for measuring and controlling the particle size in cyclone overflow streams. The implementation of this technology is centered upon a sensor probe that is inserted into the overflow slurry stream via a two-inch (50 mm) hole in the overflow pipe (Figure 1). Particles within the slurry stream impact the surface of the probe generating travelling stress waves within the probe. A sensor converts these travelling stress waves into an electrical signal and proprietary signal processing techniques convert these signals into a particle size measurement that is output every four seconds. The sensor is constantly in contact with many particles in the slurry stream, thus obtaining information from orders of magnitude more particles than traditional sample-based technologies. The sensor has no impact on cyclone performance because it is located downstream of the hydrocyclone and the presence of an air core ensures there is no change in the back pressure seen by the hydrocyclone.

Jan 1, 2019

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019

By D. M. Ziebarth

"Normal sequence of operations to develop a new underground mine is: construct and outfit headframe for shaft sinking, sink shaft, construct and outfit shaft sump, develop shaft station and shaft bottom steel. In an effort to reduce the overall project schedule, an innovative plan was developed to install service shaft steel below station level, prior to the completion of the shaft sinking effort. To better evaluate the construction of this substantial steel tower, a preliminary constructability evaluation was conducted, including the best method of supporting the main tower; from the bottom, middle or top of the tower. The design criteria and plan involved: •,Develop access from existing service shaft, 25 km underground •,Use of materials to maximize strength while minimizing corrosion exposure •,Estimating the location of the shaft centerline •,Over excavating the station and shaft below station to allow future shaft steel repositioning •,Designing the tower steel for modular installation •,Incorporate commissioning considerations, such as suspension of the cheese weights during steel installation •,Provision for covered stair access to shaft bottom •,Enclosed shaft envelope with open panels to allow visibility and ventilation The design approach was innovative and this paper will describe the design principles and challenges encountered while providing insight into the solutions developed and implemented; especially the modular construction and installation methodology. INTRODUCTION In an effort to expand the mining operations, a plan was developed to construct a new service shaft closer to the new mine workings and convert the existing service shaft to a production shaft at the Potash Corporation of Saskatchewan Inc. (PCS now Nutrien) Rocanville Potash mine in southeast Saskatchewan. The new service shaft required a multi roped friction hoist operating a cage / counterweight, rope guided conveyances to support the operational requirements. The service shaft is an integral part of the mining infrastructure as it provides access to the underground workings, transport personnel and materials underground for operation and maintenance of the mine. The shaft also allows for services required for safe operation of the underground mine, power supply, controls, communication, dewatering and fresh water supply."

Jan 1, 2019

By Damian Connelly

The option to leach iron from low grade copper concentrates could reduce transport costs and significantly improve the saleability of the concentrate. In addition, it reduces smelting costs and can remove undesirable impurities. The trend to produce cleaner and higher grade copper concentrates is very appealing to the smelters. A recent copper project came on line and there were three serious deficiencies which were not identified in the feasibility study. This came as a surprise and resulted in a number of projects to investigate ways of rectifying the problems in the shortest timeframe possible and using minimal new capital. The first serious issued not identified when commissioning was the lower than expected copper recovery, which was 70% compared to a predicted recovery of 80% to 87% in the feasibility study. This required investigating new flotation reagents and incorporating controlled potential sulphidisation. The second serious issue overlooked is the presence of significant amounts of talc minerals (insol) in the ore which are naturally floatable. This leads to lower concentrate grade and attempts to remove the talc resulted in lower copper recovery. Smelters have limits on the amount of talc in concentrate because it produces viscous slags and difficulties for the smelter. It also incurs higher transport costs. The third serious issue not identified in the feasibility study was the high arsenic reporting to the concentrate. Arsenic is a penalty element for smelters and at levels exceeding 0.3% the smelters may reject the concentrate. Arsenic is a problem environmentally for copper smelters and penalties apply when it is high. This paper describes the options for penalty element removal and suitability to incorporate into the modified flowsheet. It also highlights where the geometallurgy was not properly addressed and how these surprises could have been avoided. INTRODUCTION From 1970 to 1985, a copper company undertook metallurgical testwork on the Peruvian project copper ore. The ores were mined underground and treated over many years previously. Various other groups undertook studies and work until Aker Kvaerner undertook a feasibility study in 2006. Three ore composites were tested and grind-recovery relationships were developed. The feasibility study testwork identified that talc was a possible concern and will have an impact on copper concentrate grade. This was to be managed by blending. The current operating reality is that there is so much talc in the ore body it is not possible to blend it out. There was far more emphasis on molybdenum recovery. No mention was made of arsenic issues other than blending. There was a Concentrate Leach Study and a Molybdenum Hydrometallurgical Plant Study but these options did not proceed to a final flowsheet. A Scoping Study in 2006 looked at a Heap Leach project. The heap leaching gave very poor copper recovery on the sulphide ore. Heap Leaching was evaluated and tested for the high talc and high arsenic ore but recoveries were poor. The Aker Kvaerner feasibility study opted for a simple primary crush SAG/ball grind followed by flotation and sale of a concentrate. This is the current flowsheet utilised and the scale of the project is very large based on processing 117,200 tonnes of ore per day. A feasibility study does not guarantee success and the deviations from the feasibility study suggest there is a lot of technical work required to improve the current metallurgical performance.

Jan 1, 2019

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By J. A. Scott, K. Moreau, H. Shang

"Trials of automated technology at underground mine sites around the world have reported increased production and the potential for lower energy consumption. Autonomous mining eliminates a range of delays related to operator downtime and travel to the workface and facilitates continuous operation in conditions that are unsafe for workers. Automation also introduces complexities and safety hazards arising from equipment–personnel interactions; automated processes must be isolated from other stope-cycle–related activities such as production drilling, development, loading, and backfilling, poten¬tially requiring changes to the mine design to maintain an efficient and safe operation. This paper reviews and discusses the implementation of automated equipment in deep underground mining operations and the challenges and advantages associated with the technology. ¦ KEYWORDS Automated equipment, Emissions reduction, Energy, Productivity, Sustainability, Technology, Underground mines RÉSUMÉ Des essais de technologies automatisées dans des sites miniers souterrains aux quatre coins du monde ont indiqué une production accrue et la possibilité de réduire la consommation d’énergie. L’exploitation minière autonome élimine tout un éventail de retards liés aux temps d’immobilisation des opérateurs et aux déplacements vers le front de taille, et facilite l’exploitation continue dans des conditions qui s’avèrent peu sécurisées pour les travailleurs. L’automatisation introduit également des complexités et des risques pour la sécurité, qui surviennent en raison des interactions entre l’équipement et le personnel. On recommande d’isoler les procédés automatisés des autres activités liées au cycle des chantiers telles que le forage de production, le développement, le chargement et le remblai, ce qui pourrait entraîner des changements au niveau de la conception de la mine afin de préserver rendement et sécurité dans l’exploitation. Cet article examine et aborde la mise en oeuvre de l’équipement automatisé dans des exploitations minières souterraines profondes, ainsi que les enjeux et les avantages associés à cette technologie. ¦ MOTS CLÉS durabilité, énergie, équipement automatisé, mines souterraines, productivité, réduction des émissions, technologieINTRODUCTION As the mining industry continues to exhaust easily accessible orebodies, the need for efficient, deep (typically below 2,500 m) mine operations increases (Atlas Copco, 2013a); however, the mining process can become economically infeasible at great depths because operation costs drastically increase. This has resulted in investigations into automating mining operations as the industry strives for improved productivity (Schunnesson, Gustafson, & Kumar, 2009) and ways to remove personnel from hazardous work areas."

Jan 1, 2019

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By Nitin Bhavsar, Kaushik Vakil, Lakshmikanth Reddy, Sanjay Sarkar, Tathavadkar. Vilas, Bhavin Desai, Raghavendra Adiga

Gold and platinum group metals (PGM) do not dissolve in sulfate electrolyte from anode during electro-refining of primary copper. The PGM form solid ‘slimes’ which accumulates at bottom of the electrolytic cell. Typically, 8 to 10 ppm silver is present in copper cathodes, which is equivalent to almost 2% of silver loss during electro-refining. The silver can be cemented with cathode copper as soon as it is dissolved into the electrolyte from anode or during entrapment of slime particles in cathode. Over a period of time, the concentrates grade has deteriorated and change in type & amount of impurities in concentrate has resulted in higher silver loss during refining process. Therefore, an in-depth investigation was carried out in both fire- and electro-refining processes to understand the root causes of higher silver loss in copper cathodes. The detailed characterization and the plant data analysis were carried out. The results of study revealed that higher silver loss in 3rd crop cathodes as compared to 1st and 2nd crop cathodes from same anode. In anode silver was present in two forms, dissolved in copper (solid solution) and in slime phases such as Cu2-xAgxSeTe. SEM-EDX study of anode cross section confirmed higher silver and oxygen content in central region (core) of anode as compared that in both air and mold sides. This is due to non-uniform cooling of anode which was confirmed by the solidification modeling. Higher concentration of oxygen & silver at core of anode rised Ag+ concentration in electrolyte and slime particles during 3rd crop. The results of study were used to optimize the anode cooling process and also electrolyte chemistry to reduce the silver loss. The details of study carried out are discussed in this paper using the results of modeling, characterization and experimental studies. INTRODUCTION In the electrolytic refining of copper, fire refined copper anodes are used as raw material. Anodes contains copper of the range 99.5 to 99.6%, rest being the impurities. Hence, the purpose of the refining is (1) to remove the impurities so that final cathode conforms to the LME specifications and also (2) to recover the precious metal from the anode copper. When anode is dissolved, most of the impurities reports to the anode slime settled at the bottom of the cell, and rest dissolves in the electrolyte. Dissolved impurities remains in electrolyte and are removed during electrolyte recycling. However, sometime dissolved impurities and slime particles get entrapped in cathode due to disturbances in operational conditions. Metals dissolving in the electrolyte are the elements such as Ni, Co, Fe, Zn. The electrode potential of As, Sb and Bi being close to that of copper, these elements partly dissolve in the electrolyte. Noble metals like Ag, Au, Pt and Pd are generally insoluble and are thus expected to report to the anode slime. A small amount of the sliver content from the anode is dissolved in the electrolyte. Because the dissolved silver electroplates on the cathode at a smaller applied potential than copper, the cathode typically contains up to 8 ppm of silver. This is referred to as ‘silver loss’ in cathode (Cooper, 1987). Fortunately, silver is a rather benign impurity in copper due to its electrical conductivity being higher than copper. However, higher silver loss in cathode is loss of revenue for Copper smelter due to significant difference in their LME price.

Jan 1, 2019

By T. E. Wakefield

"Final Galloway (stage) designs for vertical drill and blast shaft sinking projects evolve from complex thought patterns which integrate operational processes, systems and methods of communication, power supply, drilling, blasting, ventilating, mucking, supporting, surveying, dewatering, sealing, concrete lining and shaft furnishing. Attention to ergonomic design detail at the shaftsman / structure interface is at the heart of safe and successful multi-deck working platforms. For economy the end product must have a low mass to reduce suspension rope end loads to be able to use smaller suspension hoists and have lighter headframe structures, be robust to withstand concussion damage, be easily constructible on site, be maintainable in the shaft barrel, and comply with safety and legislated standards. This paper’s ambition is to describe a systematic design framework and sequenced thought process that delivers a product that is engineered with excellence, illustrated by making use of two designs that evolved during recent Galloway projects, one destined for a large diameter man/material shaft, the other for a ventilation shaft. The stage engineering iterative process starts with mapping permanent and sinking hoisting layouts, followed by laying out horizontal deck plans, mostly constrained by the permanent shaft purpose and configuration, whilst maximizing openings to enable muck to be removed rapidly for the best sinking cycles. Concurrently the designer needs to understand the chosen sinking methodologies in conjunction with crewing to determine the number of decks and fix their spacing. Insufficient access to move and line up formwork, set reinforcing rods and pour concrete in the confined spaces of the stage is an inherent major risk to be mitigated. An iterative and integrative process follows for the primary configuration which delves into increasing design detail, accommodating all other methodology influences, resulting in 3D layouts for further risk assessment, review and fine tuning by seasoned shaftsmen. INTRODUCTION Documented colliery shaft sinking practice from the late 1800’s makes reference to purpose built walling (bricked lining) cribs with floors suspended in sinking shafts, thereby allowing shaft lining to proceed concurrently with the excavation. Improvements were made by Sir William Galloway who introduced two decks supported at the corners by angle irons. The sinking stage, or Galloway, has developed substantially over time to be the in-barrel heart of the sinking operation, with overwhelming complexity for those who have to design one for the first time."

Jan 1, 2019

By T. Junne, L. Eltrop, S. Moreno-Leiva, J. Haas, W. Kracht

The energy systems of the future will be highly renewable. The flexibility that is consequently required can be provided with many options, the main ones being energy storage, transmission reinforcement, and demand side management. The role of the latter is explored for the copper industry, using the scheduling of maintenance services as an example of Solar-Paced Design - the coupling of energy demand with solar resource availability. We used a linear energy optimization model to define the minimum-cost configuration for a fully renewable energy system of a copper concentration plant under different scenarios for the scheduling of maintenance services. For the case we studied, (total) costs were 4% lower when the maintenance was scheduled in winter. We expect that exploring the potential of such Solar-Paced Design in the copper industry will allow new potentials for a more cost-effective full renewable energy supply of this critical industry. INTRODUCTION The mitigation of climate change requires a worldwide transformation of the energy system by the significant expansion of renewable energies and the electrification of various sectors and processes (Teske et al., 2015)(International Energy Agency IEA, 2018). Moreover, considering the decreasing costs of renewable energy technologies and the intensive use required to deliver the goals in the Paris Agreement, we can expect to have highly renewable energy systems in the near future. However, to rebuild and expand our energy systems, we need certain materials, including copper. Also, energy systems based on renewables are more copper-intensive than conventional ones (Kleijn, van der Voet, Kramer, van Oers, & van der Giesen, 2011). The mineral industry, in turn, needs clean energy to achieve a better environmental performance (e.g. solar energy for copper production (Moreno-Leiva et al., 2017)) and to avoid negative secondary effects induced by the strong expansion of clean technologies. But there is something else the minerals industry can offer in this bi-directional relation with energy systems.

Jan 1, 2019

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By T. Boyd, K. McTaggart, J. Qiu

"Hudbay Minerals’ Flin Flon process plant produces a copper concentrate and zinc concentrate from the three ores it processes: 777, Reed and Lalor. Unlike many Cu-Zn ores, the average Zn: Cu ratio in feed is around 2:1, whereas, in many Cu-Zn separation plants the Zn: Cu feed grade is substantially higher than 2:1. The lower Zn: Cu in plant feed is a challenge for limiting Zn recovery to the Cu concentrate. While total recoveries of Cu and Zn at Flin Flon are very good; selectivity is the key challenge and small changes in ore or plant, can result in quite variable Zn recovery to Cu concentrate, and accordingly, Zn recovery to Zn concentrate. Magnetic conditioning has been shown to be selective between the two paramagnetic minerals chalcopyrite and sphalerite. Statistical testing of magnetic conditioning was undertaken at Flin Flon with the objective of increasing Cu recovery to Cu concentrate without increasing the Zn recovery to Cu concentrate - in effect increasing Cu-Zn selectivity. This has been achieved elsewhere with magnetic conditioning with the probable mechanism being an increase in fine chalcopyrite recovery, and a reduction in entrained, ultrafine, non-activated sphalerite to Cu concentrate. The results did indeed show an increase in Cu recovery to Cu concentrate of 0.8% to high confidence, but the decrease in Zn recovery to Cu concentrate was not to high confidence. This is effectively an increase in Cu: Zn selectivity in the Cu circuit – higher Cu recovery with no change in Zn recovery. However, while there was an increase of 1% in Zn recovery to Zn concentrate with magnetic conditioning, the variability in this parameter meant that this increase, though larger in magnitude than the Cu result, was not to high confidence."

Jan 1, 2019

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019