Search Documents

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By Melanie Grob

Two commonly estimated fractal dimensions, called b and D values, represent statistical characteristics in the distribution of magnitude sizes (b) and spatial hypocenter locations (D) of microseismic events, respectively. We postulate that the values of b and D are related to specific stress regimes. Through different case studies of fluid injection into an oil/gas reservoir or geothermal field, we infer that the measured temporal variation in fractal dimension b is most likely due to significant changes in the local stress regime. The fracture dimension D indicates the spatial clustering of events. The distribution of these events can vary with time because of stress perturbations that (re)activate fractures whose direction favours their movement under a specific stress regime. Thus a combined statistical study of these two dimensions can help infer the variations of local stresses in a reservoir.

Jun 1, 2012

By Jaime Meléndez Martínez

Recent interest in unconventional reservoirs motivates our work in laboratory measurements of seismic anisotropy. Seismic anisotropy is the variation in speed of a wave as a function of its direction of propagation. Analyzing anisotropy in unconventional reservoirs is important since anisotropy leads, for example, to differential stresses upon loading and could affect hydraulic stimulation (Reinicke et al., 2010, Zimmermann and Reinicke, 2009); in this sense, laboratory measurements are an important tool to study seismic anisotropy at small scales which can aid in the characterization of larger formations. The purpose of this work is to describe the laboratory methodology used to simultaneously measure ultrasonic P and S-waves in three different directions from a single core sample. Elastic anisotropy of a Proterozoic sedimentary rock from south-west Alberta is investigated. In metamorphic rocks seismic anisotropy is caused by preferred mineralogical alignment or foliation. Assuming a transversally isotropic medium, arrays of compressional and shear piezoelectric ceramic transducers were mounted on a sample trimmed from a core to measure travel times of ultrasonic P-waves and S-waves as a function of confining pressure at directions perpendicular, parallel, and oblique to the plane of foliation (bedding). Results show strong anisotropy agreeing with the assumption of a transversely isotropic medium. Dependence of travel times and hysteresis effects can be observed when pressurizing and depressurizing.

Jun 1, 2012

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By Gregory C. More O'Ferrall

Generally pillars in the Southern African hard rock tabular underground mining environment are designed using either empirical pillar design formulae or numerical modelling (analytical) methods utilizing the Hoek-Brown failure criterion. However, none of the pillar design methodologies employed takes cognizance of weak layers either within the pillar material or in the immediate foundation of the pillar. Over the past few years, the presence of a weak layer either within the pillar material or within the immediate foundation of the pillar has resulted in the closure of one platinum mine (Everest Mine), closure of one chrome mine (Wonderkop Chrome) and large-scale instability in a couple of chrome and platinum mines in South Africa and Zimbabwe. A study has been initiated to better understand the failure mode and strengths of the pillars where pillar failure associated with weak layers occurred. Owing to the infancy of the study into the failed pillar strength and failure mechanism, the purpose of this paper is to highlight the circumstances that led to the collapse of mining sections and a shaft, and the difficulty associated with designing pillars in the Southern African chrome and platinum mining operations.

Jun 1, 2012

By F. Guo

"The leaching kinetics of zinc sulphide concentrate was studied under total pressures ranging from 0.3 MPa to 0.5 MPa and leaching temperatures ranging from 358 K to 378 K. The apparent activation energy of leaching reaction under different total pressures was calculated. The results show that for the extraction of zinc at low-temperature pressure leaching is controlled by an interfacial chemical reaction. This was supported mineralogical analysis of the leaching residue. The kinetic equation for low-temperature pressure leaching of zinc sulphide concentrate was further established by quadratic regression on the basis of shrinking core model.INTRODUCTIONThe Roast-Leach-Electrowinning Process (RLE) is the primary route for zinc production and responsible for more than 85% of the total zinc production (Souza et al., 2007). During the roasting of zinc concentrates, fugitive SO2 causes pollution. The prevention of SO2 emissions from the RLE process can be one of the challenges to this technology (Deller, 2005). In the 1980s, the Zinc Pressure Leach (ZPL) process changed the concept of zinc hydrometallurgy, in which zinc sulphide concentrate is directly leached at approximately 423 K and approximately 0.7 MPa oxygen overpressure and the sulphidic sulphur is oxidized into elemental sulphur so that the pollution by SO2 is completely avoided. Since 1981, five zinc plants have adopted the ZPL process either for expansion by integration with existing roasting facilities, or for the production of zinc without any roasting at all (Collins et al. 1994; Barth et al. 1998). The innovation of the ZPL process has made the zinc industries more competitive although it needs an autoclave. The direct leaching technology of zinc is still in development."

Jan 1, 2012

By J. B. Hadaway

The operation at Phu Kham commenced design and construction in early 2006 and was commissioned in May 2008. This paper will examine and discuss the project from the inception of flow sheet development and equipment selection, equipment design and manufacture, construction, commissioning and ramp up to full production. The paper will touch on the strategies employed to achieve a short schedule and the efficient use of capital, but with the main emphasis on the grinding circuit. Various challenges during the early years of operation will be discussed including the effect of ore characteristics, including competency, on the performance of the grinding circuit. Actions to overcome these challenges and to enhance performance will also be discussed. Finally, current and future plans to improve the performance of the grinding circuit and the overall plant will be summarised.

Jan 1, 2012

By E. V. Manlapig, U. Erol, V. Ross, K. Tshimanga

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By Alexander Potapov, Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY’s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By H. Paudyal, K. Ohto, H. Kawakita, S. Alam, B. Pangeni

The orange waste after lime water modification was converted into promising adsorbents for fluoride by metal loading reaction. The effectiveness and mechanism of fluoride adsorption on metal loaded orange waste gel from synthetic and real plating solution were investigated. Amount of zirconium(IV), aluminium(III), cerium(III), lanthanum(III), titanium(IV), vanadium(IV) and tin(IV) loaded on orange waste from aquearegia dissolution were evaluated to be 1.62, 1.16, 0.93, 0.95, 1.20, 1.12, 0.97 mmol/g respectively. The maximum adsorption capacity (qmax) of zirconium(IV), cerium(III), lanthanum(III), iron(III) and aluminium(III) loaded orange waste for fluoride ions were evaluated to be 1.74, 0.91, 1.07, 0.98 and 1.01 mmol/g from aqueous solution. The mechanism of fluoride adsorption by metal loaded orange waste was inferred to be ligand exchange reaction. Application of zirconium(IV) loaded saponified orange juice residue(SOJR) for real plating solution showed effective removal of trace concentration of fluoride down to the accepted standard. The negligible interference of co existing anions like nitrate, carbonate, sulphate and chloride makes zirconium(IV) loaded SOJR a promising sorbent for waste water treatment. The adsorbed fluoride from fluoride loaded zirconium(IV)-SOJR was effectively desorbed by using alkali solution for its regeneration. This work shed light on the potential application of metal loaded SOJR to remediate fluoride contaminated water for environmental relevance.

Jan 1, 2012

By I. Southern, S. Kelebek

"Smelting furnace bricks contain significant quantity of base metals trapped in refractory material. A series of flotation tests were carried out on samples of old bricks from Sudbury area to examine upgrading behaviour for recycling purposes. Depending on the grind size used nickel recoveries varied from 60 to 90.6% with corresponding grades of 20% and 14.7%Ni. There is a trade-off between nickel and copper. The nickel has responded well to fine grinding, however, the copper recovery suffered from it. Mineralogical characteristics and flotation behaviour of the brick material are discussed in reference to those from the primary ore. INTRODUCTIONMineral processing is well recognized as a mature technology not only for the mining industry, but also for the environmental industry for the purpose of remediation and recycling. Materials available for recycling are usually the products of many years ago. There are multiple stake holders in this area. In general, when the processing results in a product that can be reused or sold, the company carrying out the remediation makes a profit, while the regulators and the public are pleased due to a cleaner environment. From these points of view, there have been many papers published over the years on various mineral processing techniques applied to separation of many different materials including from mining and metallurgical industries (Wilson et al., 1994; Tsunekawa et al., 2005; Saikia et al., 2012).Flotation may be viewed as the backbone of the mining and metallurgical industry since its invention for separation of solids from one another almost a century ago. It is capable of recovering a variety of finely divided different solids following their liberation from each other. Its versatility and highly competitive nature in terms of cost per tonne of material processed, accounts for its occasional uses in the environment engineering area. In the mining industry, flotation is the standard method used for the sulphide ores. It can be applied as a bulk flotation and/or differential flotation. Bulk flotation, which refers to co-flotation of several components from their source, is most suitable for environmental cleanup objectives. Desulphurisation of various plant tailings is a typical example of this (Benzazzoua et al., 2000)."

Jan 1, 2012

By D. Yu, T. A. Utigard, M. Barati

"Sulfation roasting of nickel concentrate to generate water-soluble metal sulfates was investigated as an alternative process to smelting for the recovery of valuable metals. The kinetics of dissolution of various species of the calcine in three leachants was studied; hot water, dilute HCl, and concentrated HCl. The results indicated that dissolution of sulfates by hot water at 90 ºC is achieved within 30 minutes. In order to increase the recovery of the valuable metals, acid leaching is necessary due to the existence of ferrite in the calcine.INTRODUCTIONInvestigations on the sulfation roasting of nickeliferous sulfide ores or concentrates were mainly carried out in 1950’s to 1990’s to generate water soluble non-ferrous metal sulfates followed by metal recovery by leaching (Stephens, 1953; Thornhill, 1954, 1961; Fletcher and Shelef, 1964a, 1964b; Fletcher and Hester, 1964; Frankiewicz, 1977; Norrgran, 1983). Commercialization of the sulfation roasting process was only performed by Falconbridge Ltd. (Thornhill, 1961; Boldt, 1967), which employed a sulfation roast process on nickeliferous pyrrhotite at 680 oC where Ni, Cu, and Co were leached and Fe2O3 was produced for the iron industry. In 1965, 118,342 tons of pyrrhotite was processed, however because of the huge SO2 emissions (no acid plant) relative to the nickel production and the poor economics, this plant was shut down.Nickel production from sulfide ores via pyrometallurgical means, especially the electric furnace smelting process, is a major emitter of SO2 to the environment and a big energy consumer (Warner, Diaz, Dalvi, Mackey, Tarasov and Jones, 2007). Nowadays, due to the more stringent environmental regulations as well as the need to reduce energy consumption, metal production by sulfation roasting is gaining more attention as an alternative process to smelting. The main focus of this paper is to investigate the extent and rate of leaching of valuable metals from the sulfation roasted nickel calcine, aiming to maximize the metal recovery and minimize the dissolution of iron species."

Jan 1, 2012

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

The AG/SAG circuit discharge P80 is now increasingly referred to as the ?Transfer Size? or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012

By M. Sukhram, S. A. Argyropoulos

"In the aluminum and steel processing industries there is a need for velocity sensors to measure the flow characteristics of liquid metal. This paper will present a sensor and an inverse heat transfer technique to determine the direction of velocity in flowing liquid aluminum. Experimental research work with the sensor involving liquid aluminum was conducted, using the Revolving Liquid Metal Tank at the University of Toronto, which rotates 50 kg of liquid aluminum with velocities up to 0.35 m/s. Experimental data for various magnitude of velocity demonstrate that the sensor records different thermal profiles under different fluid flow conditions. Using the transient temperature information and the inverse technique, the direction of velocity of the molten aluminum flow field can be inferred. INTRODUCTIONOur research at the University of Toronto has focused on developing invasive sensors to determine the velocity of high temperature liquid metals. High temperature in this setting is defined at VALUES (in excess of 660 °C. The discussion which will persist in this manuscript involves detecting the direction of flow in liquid aluminum using an inverse heat transfer technique. We first reported on the sensor which is used in this article in the following two publications (Sukhram and Argyropoulos, 2011a; Sukhram and Argyropoulos, 2011b). The motivation to perform this research is due to the lack of sensors available to characterize the conditions within a high temperature liquid metal reactor/vessel. A report conducted by The Minerals Metals and Materials Society (TMS Energy 2011) has suggested that the introduction of sensors into molten metal processing environments has the potential to increase process efficiency up to 15%. Such sensors will aid in the understanding of high temperature liquid metal processing operations with the goal to implement more efficient process design and practice."

Jan 1, 2012

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

The Santa Rita mine is located in north eastern part of Bahia in Brazil and is owned and operated by Mirabela Mineração do Brasil Ltda. Typical SABC circuit was designed as the preferred option for the 4.0 mtpa (500tph) to produce a P80 of 125um for flotation. Although the SAG was originally designed to operate with conventional radial pulp lifters, later it was fitted with Outotec?s Turbo Pulp Lifters ? TPL (Latchireddi, 2005). The milling circuit commenced commissioning on the 24th of October 2009 and the milling circuit achieved the nameplate capacity within days. with small and relatively simple measures to rectify. Since commissioning, the SAG mill has been working in fully autogenous grinding (FAG) mode with no balls (in contrast to the estimated 10% ball charge) and has been consistently treated up to 650tph. This paper examines the comminution design process, the operating philosophies, start-up experiences, post commissioning optimization and future development works. An evaluation of mill performance relative to the design criteria for the project life to date is also included.

Jan 1, 2012