Search Documents

By Jane Spooner

"The papers presented in this edition of the Bulletin cover some of the business issues that face mining companies exploring or operating in jurisdictions outside Canada. While technical innovations may, generally, be seen as fast-moving and farreaching, these papers also show that changes in approach and thinking continue to be evaluated and implemented.The Forum paper co-authored by Roger Taplin of McCarthy Tétrault LLP and Marchand Snyman of Muratie Investments Pty Ltd. highlights the quite radical changes that have taken place in South Africa’s mining industry with the introduction of the Mineral and Petroleum Resources Development Act, 2002, in October of that year, together with the Broad-based Socio-Economic Empowerment Charter for the South African Mining Industry and the Mineral and Petroleum Royalty Bill of March 2003."

Jan 1, 2004

By Muhammad Tawalbeh

The calculated temperature history of a single particle of MgCl2 hydrates when it came in contact with fused salt electrolyte at 650 °C was determined using the measured heat transfer coefficient for the molten salt bath at 650 °C. The calculations revealed that the entire interior of the particle reached the temperature required for the formation of MgOHCI from hydrated MgCl2 in less than 2 seconds. This was much less than the time required for dissolution of the prills as observed in experiments. It is very likely that the formation of MgOHCI during prill dehydration and dissolution is a result of hydrolysis in the interior of the prills.

Jan 1, 2004

By Z. -G. Ren, J. -S. Qian, Y. -G. Yang

The waste slags from chemical and metallurgical plants contain approximately wt 1% water soluble Cr6+. This hexavalent chromium is very harmful to human health, and the treatment of the slags has concerned metallurgists for many years. A sintering method was developed to treat the waste slag. In this process, sinter was made from a mixture of the waste slag containing hexavalent chromium, iron concentrate and coke breezes. During sintering, hexavalent chromium was reduced to trivalent chromium. The latter is known as a non-harmful material and can be used as chromium resource for the production of ferrochromium or chromium-containing cast iron. After sintering the hexavalent chromium in the sinter could be reduced to less than 0.0008%. It was found that the waste slag with fine particles was favourable to the Cr6+ removal. An increase of carbon content in the sintering mixture could increase the rate of Cr6+ removal and the strength of the sinter produced. The rate of Cr6+ removal increased with increasing basicity of the sintering materials with basicity less than B=1.8, above which it decreased with increasing basicity. Blast furnace was found to operate smoothly when using the sinter made from the waste slag containing chromium. However the productivity of sintering machine was slightly low compared to the sintering operation using ordinary raw materials.

Jan 1, 2004

By M. Timmins

Campbell Mine operates a 100 tpd gold autoclave that treats sulphide concentrates at 305 psi and 200 °C. Autoclave feed consists of fresh pretreated concentrate, an acidic oxide slurry recycle as well as other high arsenic sources. The brickwork that is used to construct the five compartments of the vessel must be inspected and repaired periodically. Shutdowns are scheduled to inspect this brickwork and at times replace entire sections of the brick walls or lining. It also provides an opportunity to repair or replace other internal features such as agitator blades or oxygen spargers. Mechanics and contractors are scheduled around the clock to perform the maintenance requirements. There are many safety considerations and precautions that must be taken in order to protect the well-being of the workers and minimize damage to sensitive pieces of equipment. Heat, arsenic and lead contamination and confined space issues are just a few of the hazards involved. The following paper will describe how these safety concerns are addressed and will serve as a guide for future autoclave shutdowns.

Jan 1, 2004

By S. Torizuka, I. Mizushima. Kawasakitohri, A. Ohmori, K. Nagai

Strain (work)-hardening in tensile tests were examined for low carbon steels with various ferrite grain sizes ranged from 0.4µm to 16µm. The steels had microstructures composed of ferrite grains and dispersed cementite particles. They were fabricated through warm caliber rolling with an accumulative area reduction of 93%. Strain-hardening rate at a given strain increased with an increase in volume fraction of cementite particles. The balance of yield strength and uniform elongation for ultrafine-grained structures could be improved by the dispersion of cementite particles. Effects of the cementite dispersion and the ferrite grain size on the strain-hardening rate can be roughly explained by the work-hardening model with GN-dislocation density. Strain-hardening design using dispersed cementites was proved to be effective in controlling ductility of the ultrafine-grained steels.

Jan 1, 2004

By W. Lo, M. Brothers, G. Oprea, G. Richard, T. Troczynski

Magnesia-chrome and chrome-magnesia are the most used refractories in contact with iron-rich non-ferrous smelting slags. The corrosion by slag always brings chromium oxide into the slag, causing the precipitation of crystalline phases at the process temperature. This secondary effect of the chromium-bearing refractory dissolution was studied in this work, emphasizing the effect of the other chemical components of the slag at various temperatures. The experimental results showed that the presence of chromium and lead contribute, although in different ways, to the formation of complex spinel phases and their precipitation at temperatures in the range of 1250-1400°C. The XRD and SEM/EDS results were discussed for refractory-slag mixes containing 0-20% Cr2O3 and 0-11% PbO.

Jan 1, 2004

By M. Rigaud, N. Zhou, K. Sankaranarayanane, X. Zhou

The effect of amount and type of dispersants on the rheological behaviour of bauxite-based low-cement castables has been studied in detail. The rheological properties: flow resistance and torque viscosity, as measured by a rheometer, are found to be strongly influenced by the amount and type of dispersants. In the present investigation, a mix containing sodium hexametaphosphate, at an optimal level, is observed to be theologically superior at the given experimental conditions.

Jan 1, 2004

By J. Zinck

The management of mine wastes generated by both active and inactive mining is an ever more challenging issue. The cost to manage and treat mine wastes, including tailings, waste rock, treatment sludge and slag, is estimated at over $50B in Canada and the United States alone. Cost-effective technologies are required to meet both short and long term challenges and increasing environmental standards. This paper will provide an overview of novel and conventional technologies to manage mine waste particularly in the areas of waste stabilization, treatment and disposal technologies.

Jan 1, 2004

By E. M. De Souza, J. F. Archibald

This paper examines aspects of Canadian mine backfilling operations that may be implemented to assist in reducing solid waste production, lowering energy costs, and restricting Greenhouse Gas emissions. Many Canadian underground mines use backfill to mitigate environmental effects associated with tailings disposal. Backfill production and disposal are energy intensive processes that require an average energy cost of 37.7 MJ/tonne of backfill to complete. Mine backfills, in engineering applications, also commonly make use of cement as a stabilizing agent. Cement requires an additional energy cost ranging between 4,637 and 6,600 MJ/tonne to produce. The large energy needs associated with mine backfilling and cement production operations create significant CO2 and Greenhouse Gas emissions. Approximately 1 tonne of CO2 and Greenhouse Gas is emitted for each tonne of Normal Portland Cement produced. For single mines producing 3,000 tonnes of backfill per day, considering both backfill and cement emission source terms, total emissions of CO2 ranging between 120.36 tonnes and 169.44 tonnes/day are anticipated. In Ontario, mining operations contribute 700,000 - 840,000 tonnes/year of CO2 and Greenhouse Gas emissions to satisfy backfill cement consumption needs alone. Potential reductions of cement in backfill would significantly reduce emission of these gases and lower their adverse environmental impacts. This paper identifies alternate, equally effective and lower cost binder agent strategies for cement in backfill that may lead to cement consumption reductions. Post-consumer glass represents one such potential alternative backfill binder. Over 950,000 tonnes of glass are disposed of annually in Canada, two-thirds of which exists in the form of easily recoverable glass packaging that is not currently recycled or reused. The partial replacement of cement by waste glass may address goals for reducing non-recyclable glass waste disposal; enhancing mine back filling operations; reducing total backfill energy costs; and ultimately reducing Greenhouse Gas emissions levels currently generated by the Canadian mining industry.

Jan 1, 2004

By M. Hosseinzadeh

By changing the quality of consumed refractory bricks in burner zone of sarcheshmeh copper complex anod kiln removing of carbon precipitation phenomenon was studied. For blister deoxygenation LPG is blowing in anod kiln and cause destoring microsturcture and bonding of refractory bricks. Studies are shown that in a part of the bricks which have a temperature of 800 - 1000 °C , iron content phases in magesia - chromite bricks are like catalist and cause increasing the rate of carbon precipitation reactions . In a way that in comparsion of two bricks with best and medium quality with different analysis, this problem is more critical in best quality bricks containing high iron oxide. Therefore special magesia spinel bricks suggested and installed in burning zone.

Jan 1, 2004

By P. Bonadia, A. Tabereaux

Nearly all aluminium smelters are increasing the potline amperage to achieve higher aluminium production. In some instances the higher amperage operation has a significant negative impact on shortening the lifetime of aluminum electrolysis cell cathodes due to loss of the protective sidewall cryolite ledge freeze and too rapid penetration of the cell bottom refractory lining by cryolitic bath components due to the higher temperature isotherms. Thus Cathodes require careful thermal modeling of the cathode relining designs and improved refractory materials to allow greater heat loss from the sidewall to preserve a stable sidewall ledge freeze at higher amperages, and the selection of optimum refractory barrier materials to control the penetration and reaction of bath into the cathode bottom refractory and insulation lining. This requires an understanding of the reaction mechanisms and product formation for molten NaF enriched bath and alumino-silicate refractories. It is desirable to use dense, low porosity refractory fireclay firebricks, or similar materials with a sufficiently high silica content to promote the formation the mineralogical phase albite, NaAlSi3O8, that significantly increases the viscosity of the melt which slows the diffusion of reactive species in the melt and thereby retards further bath penetration.

Jan 1, 2004

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

By E. Kordzadeh, M. Reza Bateni, M. Karaminezhaad, A. Moeini

A series of austenitic heat resistant Fe-Ni-Cr-Al alloys with different nickel contents have been investigated at 1100 ° C and 25, 50, 50,100 hours in S/0 bearing atmospheres. Before sulphidation test, the specimens were annealed in argon at 1250 °C for 8 hrs. Weight changes were measured using an automatic thermo gravimetric analyzer and corrosion products were analyzed by scanning electro microscope (SEM), energy dispersive X-ray spectrometry (EDAX), X-ray diffraction and optical microscope. The results showed that sulphidation resistance decreased with increasing nickel content. Internal sulphidation controlled by gaseous transport through cracks and pores and the formation of internal sulphide increased when liquid sulphides formed on the surface.

Jan 1, 2004

By B. Zhu

With the challenge of clearing steel production and increasing of the productivity of converter, the application of hot metal pretreatment technology in torpedo car become a key process in the steelmaking. In this article, the technologies, production and development trend of Al2O3-SiC-C bricks for torpedo cars in China are reviewed, the current application situation and main requirements for the Al2O3-SiC-C bricks are also addressed.

Jan 1, 2004

By Zhitong Sui, Feng Zhang, Li Zhang, Tie Ou, Guangqiang Li

Researches on the recovery of iron, manganese and the removal of phosphorus from converter slag were reviewed. The carbon thermal reduction experiments were carried out by induction heating the mixture of converter slag and graphite powders at 1650°C and 1800°C in a graphite crucible. It was found that 62.7% of the phosphorus in converter slag was reduced into carbon saturated iron alloy, 32.8% of that was vaporized and only 4.5% of that remained in the final product. Totally 95.5% of the phosphorus in converter slag was removed. Almost all iron and manganese was reduced to form carbon saturated alloy. It was found that the free lime in converter slag can react with carbon to form calcium carbide at 1800°C. The main phases in the reduced converter slag are dicalcium silicate and tricalcium silicate with small amount of calcium carbide.

Jan 1, 2004

By M. Specht, D. Pörzgen, W. Lorenz, A. /. Buhr, R. P. Racher

The introduction of the near net-shape casting process at CORUS Staal IJmuiden in January 2000 required changes of secondary metallurgy processes including a development towards more aggressive slag compositions in the steel ladle. Therefore the steel ladle lining has been changed from fired andalusite bricks to magnesia-carbon bricks and, most recently, to fired spinel bricks to withstand the severe slag conditions. In comparison to the andalusite bricks the new steel ladle linings have a higher thermal conductivity. This requires the capability to keep the lining warm by ladle preheaters to sustain the overall thermal stability of the steel ladle in case of interruptions during hot cycling of the ladles.

Jan 1, 2004

By K. Shitogiden, Y. Samada, T. Miki

Steelmaking slag contains nutrition such as Si, P and Fe for acceleration of phytoplankton growth. Phytoplankton can fixate carbon dioxide more than any other species on earth. Hence, suppression of CO2 can be achieved by applying the potential of steelmaking slag as the nutrition for their propagation. When it is considered to supply nutrition from steelmaking slag to seawater, we must avoid dissolution of hazardous elements or change of pH of seawater by steelmaking slag addition into seawater. The protection against dissolution of fluorine into artificial seawater has been studied based on dissolution behavior of steelmaking slag and synthesized substances into artificial seawater in the present work. The dissolution mechanism of fluorine from steelmaking slag and buffering action of pH change are discussed by using stability diagram in seawater.

Jan 1, 2004

By M. C. Bluteau, G. P. Demopoulos

Arsenic reports in the effluents of many non-ferrous metallurgical operations. The production of scorodite, a crystalline ferric arsenate, is considered as an attractive option for the fixation of arsenic from aqueous effluents. However, scorodite solubility and long-term stability in the pH region of interest for tailings disposal have not been thoroughly investigated. In this study the long-term stability of scorodite in the pH 5 to 9 region and the mechanism of scorodite dissolution were studied. Construction of eh-pH diagrams indicated that scorodite stability is highly dependant on the nature (stability) of co-existing iron-hydroxide/oxyhydroxide. It was also found that when scorodite dissolves, a ferrihydrite phase having very small particles size (nano-scale) forms and that the growth and crystallization of this material are delayed by the presence of arsenate even under accelerated (75°C) ageing conditions. Around neutral pH and ambiant temperature (22°C) scorodite seems to reach an equilibrium with ferrihydrite after 48 weeks yielding soluble arsenic concentrations < 5 ppm.

Jan 1, 2004

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By K. D. Peaslee, J. M. Soto, IéDé Smith, A. D. Saikia

Spinel-forming refractories reduce penetration of metal and slags through a tightening of the lining resulting from the volume expansion associated with spinel formation. Sintered spinel is often added to reduce the overall volume increase that results. Tests were carried out to evaluate the difference between performance in spinel¬forming and spinel-containing refractory mixes. Eight refractory linings, one (1) pure magnesia, three (3) magnesia-base spinel-forming and four (4) alumina-base spinel- containing dry vibratable mixes, were tested for four hours in contact with a low-carbon, low-manganese steel in a coreless induction furnace at temperatures in excess of 1600°C. Afterwards, sample were cut, and wear and penetration were measured. For magnesia-based mixes wear was minimized using 20-30wt. spinel formation although further experiments are required to determine the optimal value. For alumina-based mixes, there seemed to be an optimal ratio of spinel added to spinel formed that minimized penetration and wear at the slag line. Sidewall accretion occurred and the accretion was the highest for the mix with the ratio of spinel formed to spinel added near the optimum value. Therefore to design an optimum refractory mix the benefits of higher ratios of spinel added to reduce penetration and wear at the slag line will need to be balanced with the tendency to form accretions on the sidewalls of the furnace.

Jan 1, 2004