Search Documents

By Eric Barnard, Andreas Nashitati, John Tero, Guy Deschênes, Setta Mbalamba, John Rajala

The Otjikoto Mine, owned at 90% by B2Gold Corporation, is located 300 km north of Namibia’s capital city of Windhoek. The reserves from the open pit mine, estimated at 25.9 million tons with an average grade of 1.28 g/t Au, contain gangue minerals, pyrite and pyrrhotite, and have an estimated 10 year mine life. The feasibility study included an optimisation of gold leaching using CSTR for the original design. The results of the test work were used to establish the design criteria. Gravity tails from three composites (drill cores), representing the major ore types, were used. The XR3 sample (gravity tails) contained 0.32 g/t Au, while the XR2 and XR1 gravity tails samples (used for variability) contained, respectively, 0.30 g/t Au, and 0.47 g/t Au. The optimum leaching conditions were: a pre-treatment of 7 h at pH 10.5 with 100 g/t lead nitrate, DO > 5 ppm followed by cyanidation at 300 ppm NaCN, pH 10.0, DO > 5 ppm for 48 h. The gold extraction was 91.5% (97.2% overall extraction gravity/leach) and the cyanide addition was 0.57 kg/t NaCN. Increasing the DO to 16 ppm did not show any economic benefits. No pre-treatment or a 4-h pre-treatment reduced the gold leaching kinetics. The XR2 and XR1 gravity tails samples had gold extractions of 92.9% and 92.3%, respectively. At the plant scale, an 11 h pre-treatment is used followed by 42 h cyanidation with 250 ppm NaCN and an average DO of 8 ppm and 230 g/t lead nitrate in 2016. The cyanide addition was 0.49 kg/t NaCN. The commercial operation started on February 28th, 2015. The overall gold recovery and production were 98.4% and 145,696 ounces for 2015 and 98.1% and 166,286 ounces for 2016. It was found that retention times, gold content of leach residues and cyanide addition are comparable for the lab and the plant. Details of the Otjikoto process flowsheet are discussed in this paper along with the results of the lab leach optimisation test program and the plant leach circuit performance and improvements.

Jan 1, 2017

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various complex ore deposits and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides and other phases for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay & Gorain, 2014; Chattopadhyay et al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2017

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy joint venture in Madagascar is primarily limonitic in nature, containing approximately 40–45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behaviour and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behaviour of iron.RÉSUMÉ Le minerai latéritique traité par l’entreprise commune Ambatovy au Madagascar contient principalement de la limonite, composée de 40–45 % en poids (wt%) de fer (Fe) et de 1,1 wt% de nickel (Ni). Le procédé choisi pour le traitement de ce minerai tenait compte du comportement et du maintien du fer à chaque étape du schéma de traitement commercial. Parmi les facteurs pris en compte figuraient les récupérations de nickel et de cobalt, les consommations d’agents réactifs, les caractéristiques de séparation des liquides-solides ainsi que la pureté des produits semi-fini et final. Cet article compare les résultats des trois premières années d’exploitation commerciale à Ambatovy aux paramètres d’étude, en insistant notamment sur le comportement du fer.INTRODUCTIONThe main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. Ambatovy ore is primarily limonitic in nature, containing approximately 40–45 wt.% Fe and 1.1 wt.% Ni. The nickel content of the ore is approximately 1/40th that of the iron content by weight; therefore, successful recovery of nickel depends on close control of the behaviour of iron in the selected process.The Ambatovy area is located 80 km east of Antananarivo, the capital of Madagascar. Exploration dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment, and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy nickel project. Dynatec became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan, Alberta (Collins et al., 2004, 2005; Collins & Vardill, 2005; Collins, Buban, Holloway, Masters, & Raudsepp, 2009). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement, and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy nickel project, in 2007. The current Ambatovy joint venture consists of an integrated nickel and cobalt mining, processing, refining, and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner), and KORES (27.5% owner)."

Jan 1, 2017

By J. M. Bowen, P. Wemyss

"Gold losses to natural carbonaceous matter during cyanide leaching have been investigated for over a century. The variation in the severity of the problem from one ore to another has led to a range of different processes being implemented at different mine sites. Most commercial options utilise one or more of the following processes: roasting, carbon pre-flotation, organic blinding, CIL, chlorine passivation, pressure oxidation, biological passivation, elevated temperature CIL, RIL and thiosulfate. This paper provides a background to identify the most appropriate process or combination of processes for a particular ore. It also presents information on how these processes may be implemented, drawing on information in the literature and from current or recent applications at operations such as the following: Stawell, Kumtor, Penjom, Twin Creeks, Macraes Flat, Kittilä, Fosterville, Inata, Carlin, Goldstrike, and Jerritt Canyon. Various process options have been dismissed, or deemed unsuccessful due to limited knowledge available on the strengths and weaknesses of the different options and their implementation. The authors have collectively been involved in flowsheet development and project implementation in four commercial plants that have treated preg-robbing ores.INTRODUCTION Cyanide processing has been the mainstay of gold recovery for well over a century. It is generally a very effective process with over 90% recovery on free milling ores, but complex and refractory ores may only give 0–50% recovery with conventional processing (La Brooy et al., 1994). People have written about gold losses to natural carbonaceous matter during cyanidation for over a century e.g. Feldtmann, (1915). The earliest reports related to African operations, but the issue has since been reported in Canada, North and South America, Australia, Russia and China. The phenomenon is usually referred to as ‘preg-robbing’ dating from the times before the use of granular activated carbon for gold recovery, when gold was lost from the pregnant solution before it could be separated from the leach solids and recovered by cementation. Many excellent reviews have been published e.g. Dunn et al. (2013), summarising the options considered and where they have been applied commercially."

Jan 1, 2017

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By Schoeman L., K. C. Sole

Evaluation and measurement of the influence of changes in conditions and electrolyte composition during early stages of a growing metal electrodeposit are crucial to predict changes in developing morphology. A galvanodynamic polarization technique was developed to reliably measure overpotentials for nickel electrodeposition from sulfate electrolyte. The validity of these polarization parameters as indicators of the relationships between changes in the electrolyte and resulting deposit morphology was evaluated for electrolytes of varying composition. Findings indicate that nucleation and plating overpotentials measured by the described technique can be used as indicative tools for monitoring, evaluating and ultimately improving control of the electrodeposition of nickel from sulfate electrolytes. The results predict that nickel deposits of desirable quality and morphology are obtained when plating overpotentials are higher than 700 mV vs. Ag/AgCl and nucleation overpotential is less negative than plating overpotential.

Jan 1, 2017

By H. Nouranian, M. Askari

GOLGOHAR Mining & Industrial Co., with annual production of 16 million tons, is one of the largest pelletizing and iron ore supplier in Iran that recently this year, because of using mineral processing techniques and extraction of ore body positioning between the metamorphic rocks, about 150 million tons of dry tailings has been created as a result of concentrate production. On the other hand, many environmental issues such as groundwater pollution have been developed by sulfide and silicate gangue minerals, which containing heavy metals such as mercury and arsenic. In this study, a new product with high added value has been introduced for the company by identification and extraction of industrial minerals in dry tailings. Also, by removing large masses of dry tailings, environmental pollution sources were gradually eliminated. This method can be used as a modern waste management approach in the world.

Jan 1, 2017

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By Clemens Kuhnert

"Nickelhütte Aue GmbH is specialized in the recycling of waste materials containing non-ferrous metals. We treat nickel, copper, cobalt, vanadium, molybdenum and precious metal containing materials like spent catalysts, ashes, dusts, grindings, liquids, slurries and sludge's as long as they contain one or a combination of the above mentioned metals. In our pyrometallurgical works we produce non-ferrous metal concentrates suitable for further treatment in our hydrometallurgical plant where we refine Ni-, Cu-, Co- and V-chemicals. Our production is based on synergy effects due to the combination of pyro- and hydro-metallurgy. As an example we can mention our heat recovery system and internal recycling of by-products. Furthermore, the use of alternative fuels instead of fossil fuels contributes to the economic and environ-mentally friendly treatment system.INTRODUCTION Nickelhütte Aue GmbH (NHA) can look back on nearly 400 years of tradition as a pyrometallurgical works and recycling company. The existence since its foundation in 1635 as a blue dye works shows responsible and successful action in the past. Therefore, we see highest customer service, minimization of interferences with nature by closing material cycles and maximized health and occupational safety protection by avoiding injuries and diseases, still as our future duties. These duties are evaluated and monitored by an integrated management system that meets the standards of DIN EN ISO 9001, 14001, 50001 and BS OHSAS 18001. We commit ourselves to the observance of all juridical and customized demands. The management and the department managers perceive their model function. We require responsible action from all employees. To protect the continuity of our enterprise, we will also perform in future continuous improvement of products and their quality, as well as steady progress in the areas of environment protection, health protection and industrial safety. Equally the effectiveness and propriety of the management system is checked and developed regularly. In order to obtain the objectives resulting from this policy, our company determines activities and measures by involving all employees."

Jan 1, 2017

By M. Epiney, A. Ghahreman, R. Kim1and

"In the presence of sulfidic refractory ores, increasing the dissolved oxygen (DO) concentration can positively affect the gold leaching rate. To identify the role of DO in gold cyanidation, electrochemical behavior was studied in the presence of 3 different ores. Sample 1 was a low sulfide pyrite ore, contained 5.14% pyrite, 0.19% galena and 3.09% S. Sample 2 was a pyriticore as well, contained more sulfide as 8.35% S, and 12.4% of pyrite. Sample 3 was a tailing of silicate gold ore, still containing75 g/tAu, 0.13% Pb and 0.18% S. Gold cyanidation kinetics were studied by cyclic voltammetry (CV) and chronoamperometry tests. With sample 1, the gold oxidation peak current density from CV curve was increased to 1.38mA/cm2under oxygen injection, while it was only 0.66 mA/cm2with air injection. From chronoamperometry test, the reaction rate was also faster under oxygen injection. Sample 2 showed similar behavior with sample 1, but the gold oxidation peaks higher than sample 1, i.e. 1.75 and 2.27 mA/cm2, under air and oxygen injection, respectively. However, it seemed that the gold oxidation was impeded by sulfide ions for a longer period. In the presence of sample 3, the gold oxidation peak was the highest among three ores –2.75mA/cm2under oxygen injection, because of its lowest sulfide content. However, from chronoamperometry test, it was also shown that the gold oxidation was impeded because of a significant amount of Pb in the ore sample.INTRODUCTIONIt is well known that gold is leached under oxidative condition (Marsden &House, 2006). Through the most representative and oldest gold leaching technique, cyanidation, more than 90% of gold can be selectively leached from an ore. According to Elsner’s equation, gold is leached in cyanide solution by forming cyanide complex [Au (CN)2–], and oxygen is consumed as an oxidant(Eq. 1)."

Jan 1, 2017

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017