Search Documents

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb/Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb/Zn ore was traced to a pH effect. In the pH range 9.5-11 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH) 2 is suggested, the Fe++ions being derived from superficial oxidation of pyrite in the ore.INTRODUCTIONGalena and sphalerite commonly occur together. The usual practice is to float galena first followed by the flotation of sphalerite after activation with copper (II) sulphate. If ores contain pyrite it is depressed by maintaining an alkaline pH (9- 10) and using NaCN as depressant.In flotation tests with a Pb/Zn ore from Polaris selective flotation of galena could not be achieved consistently as a considerable amount of sphalerite, even though unactivated, floated. A systematic study was carried out to determine the cause of this problem. This led to the unexpected finding that sphalerite floated in the alkaline pH range 9.5-11.0 without preactivation with Cuso 4 . This paper describes the results of this study and discusses a possible mechanism of the flotation of sphalerite."

Jan 1, 1987

By C. F. Gleeson, D. G. Sheehan

"The results of humus and overburden geochemical surveys over the Doyon, Bousquet and Page-Williams gold ore deposits are presented.These studies show that humus sampling for gold gives negative results over the Doyon deposit. The lack of response is probably caused by the presence of 1 m of relatively impermeable glaciolacustrine clay and silt that overlies 1 m to 2 m of till over the surface expression of the ore zone. By contrast, positive responses for gold occur in humus samples over the Page Williams A and C gold deposits. The ""A"" ore zone is covered by several metres of exotic calcareous till over 0.5 m to 1 m of older, locally derived till. Anomalous values for gold in humus range from 10 to 35 ppb over the orebody. Overburden over the ""C"" ore zones is much thinner, generally it consists of less than 2 m of sandy till. Trenching humus anomalies that range from 10 to 1360ppb Au uncovered the gold mineralization. The geochemical dispersal trains in till from the Doyon orebody and the Page-Williams ""A"" zone are relatively short (i.e. less than 200 m) because both deposits occur in the lee of bedrock highs that shielded them from extensive glacial quarrying. Dispersal trains from all three pyritic gold deposits can be defined using either the fine fraction or heavy mineral fraction of the till.The intensity of the gold in till anomalies over the ore zones is variable. Therefore, it would be misleading to attach rigid significant threshold gold values to overburden drilling results. Each case must be evaluated based on bedrock topography, sample density, overburden type, thickness of till, as well as size, type and orientation of the target exposed to glacial erosion."

Jan 1, 1987

By R. Mohan Srivastava

"The goal of estimation is considered in the light of decision analysis. A simple example reveals the essential elements of decision-making in the face of uncertainty. A second example shows that these elements are also key features of many mining decisions. These two examples cause us to revive an old probabilistic notion that the goal of estimation should be to quantify what is unknown. The conditional probability distribution provides the complete statement of one's uncertainty. Once the conditional probability distribution has been established, one should retain as an estimate the value which minimizes some objective loss function. A third example shows how the ""best"" estimate depends on the chosen loss function. Current practice is almost exclusively based on the least squares method, which assumes a loss function which penalizes underestimation and overestimation equally. This is unfortunate not only because symmetry is an unrealistic assumption but also because mining offers a rare opportunity to state the loss function directly in terms of profitability. Both the theoretical framework and the practical tools exist to allow us to reconsider the conventional notion of the ""best"" estimate. IntroductionThis paper looks at estimation in the mining industry from the point-of-view of decision analysis. Virtually all decisions depend on estimates since few of the important parameters are ever known exactly. In this paper we will be referring mainly to the estimation of ore grades, though the approach discussed here is generally applicable to any decision in which relevant information is uncertain.In the first section we look at a very simple example of decision-making in the face of uncertainty. We will then tum to a mining example and see that the essential features of the simple example still pertain. From these two examples it will be clear that the decision analysis approach rests on two key concepts: the conditional probability distribution and the loss function. A third example demonstrates how different loss functions produce different ""best"" estimates from the same conditional probability distribution. In the final sections we willexamine the current practice of estimation in the mining industry. Though the tools for estimating the conditional probability distribution already exist, a change in the way we think about ""best"" estimates is needed. Very little attention is presently paid to the loss function even though it is readily available in many mining applications."

Jan 1, 1987

By Denis Landry

"RÉSUMÉAu cours de dix dernières années, la compagnie Maghemite a développé, expérimenté et breveté un nouveau precédé de concentration du minerai de fer à partir de la récupération d'hématite présente au bassin de sédimentation de la Compagnie Minière Québec Cartier.A partir de cette nouvelle technologie de concentration par induction, la compagnie Maghemite produit une poudre d'hématite qui est mélangée avec du strontium carbonate à un ratio de l à 6 en poids. Le mélange homogène est achemine sur un disque d'agglomération, et ensuite incorpore dans la fournaise de la Compagnie Minière Québec Cartier. Le temps de cuisson et la température (l200°C) correspondent exactement aux critères nécessaires pour la fabrication d'aimants de céramique, Grade 5, à partir de la poudre de ferrite.IntroductionMeghemite a débuté sa production de poudre de ferrite au printemps 1986et prévoit une production de 20 000 tonnes par année dans cette nouvelle usine. A très court terrne, une usine sera construite pour la production de cinq à dix millions de Iivres d'aimants permanents par annee et à long terme qu'une usine de fabrication par robotique de moteurs à aimants permanents, utilises dans I'industrie automobile. La poudre de ferrite à base de strontium est une compose ferro-magnétique forme d'une molécule d'oxide de strontium et de six molécules d'hernatite. Ce compose d'hexa fluorite de strontium a une force tres puissante et fournit la source d'énergie magnétique la moins dispendieuse comparée aux autres aimants permanents. L'utilisation des aimants de céramique formes d'hexa fluorite de strontium a connu un croissance phenornenale depuis 1970 pour atteindre un marché de 500 millions de livres par année en 1985.II n'y a aucune autre usine de production commerciale de poudre de ferrite à base de strontium au Canada. Le facteur determinant qui a favorise l'etabilissement a Port Cartier est base sur la réduction de 30% du cout des aimants de cerarnique provenant de notre poudre. Notre debouche majeur se situe aux États-Unis et vise la production des aimants de cerarnique pour les moteurs utilises dans les automobiles, les ordinateurs et les appareils ménagers, L'objectif de cette compagnie est de réduire le prix futur des aimants de cerarnique à environ 30% du prix actuel.L'usine commerciale de production de poudre de ferrite est maintenant opérationnelle. Le financement et la construction de cette usine sont Ie résultat de l'opération d'une usine pilote sur une période de 5 ans afin de récupérer l'hematite d'un haut niveau de pureté provenant de résidus de I'usine de bouletage de la Compagnie Minière Québec Cartier (CMQC) à Port Cartier. La fournaise de CMQC est utilisee pour chauffer les boulettes cornposees d'un mélange de carbonate de strontium et d'hematite d'un haut niveau de pureté en étalant environ 5 tonnes à l'heure de ces boulettes au-dessus du tablier de boulettes de fer dans une des fournaises fonctionnant à environ 450 tonnes à l'heure."

Jan 1, 1987

By B. J. Clauzier

"The Falconbridge Limited approach to employing communication equipment is first, to determine what is required in a given situation, second, to evaluate the possible alternatives, third, to select the most suitable hardware and, fourth, to determine what modifications, if any, are required to ensure not only successful implementation but continued low-cost reliability. Two examples are examined.The first situation required remote video monitoring of an acid loadout station. Several alternatives for linking to theremote site were investigated, including hard-wired, slow-scan and microwave. A comparison of these alternatives is shown and an appraisal of the performance of the selected microwave link is presented.The second situation required direct voice contact between the two members of an underground tram crew. Alternative solutions are described and an evaluation of the selected system- SHF portable radios - is presented.ObjectivesIn general, projects must have four main objectives: (1) to improve the safety of its operations; (2) to reduce its operating and capital costs; (3) to increase the efficiency of its work force; and (4) to increase its productivity. ScopeCommunication, when used wisely, can be a good tool to achieve these objectives. Projects can be kept simple using existing technology and adapting it to a particular task. To ensure the success of the project, it was necessary: to determine the project objectives; to evaluate the possible alternatives; to select the most suitable hardware; to adapt the hardware to the application, if required; and not to provide more than is necessary.Application at FalconbridgeTo illustrate this approach, two examples of actual installations at the Sudbury Operations are presented, sulphuric acid loadout, and the Falconbridge Mine haulage system."

Jan 1, 1987

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By A. P. Annan, C. Vaughan, J. L. Davis

"The increase in the price of gold in the last decade has led to a significant increase in placer gold exploration around the world. Placer deposits occur in depressions along ancient river and stream channels. In many instances these channels have been covered with materials from subsequent erosion or glacial activity. Use of high resolution geophysical techniques to map the bedrock and soil strata can improve the probability of finding the placer deposits. The buried bedrock surface is often the factor controlling deposition. Ground probing radar (GPR) and seismic sounding are complementary high resolution techniques which can be used to map bedrock topography and soil stratigraphy. Current radar instrumentation operates best in coarse grained soils. Penetration depths of up to 30 m have been attained, and stratigraphic horizons have been mapped with spatial resolutions of better than 0.5 m. Although its spatial resolution is considerably lower than radar, seismic refraction achieves superior penetration in electrically conductive environments such as clay and silt soils. The seismic refraction method thus proves to be complementary to the radar method. The seismic reflection technique is analogous to the radar method. Current seismic instrumentation and energy sources however, provide limited spatial resolution and do not permit the use of seismic reflection for reflecting horizons lying at depths of less than 20 m to 30 m.This paper discusses the use of both radar and seismic methods for placer exploration. The radar and seismic techniques, the field methods, equipment, and data displays are presented. Field examples illustrate the high resolution mapping capabilities of the techniques. The radar data agree very well with the borehole data, and in fact they sometimes detect subtle soil strata variations associated with changes of permeability that were not initially observed in the borehole logging. The radar method can give a continuous profile of water table and bedrock in sandy soils. Seismic soundings are necessary to differentiate between the bedrock and water table reflections observed by the radar."

Jan 1, 1987

By Poul Hansen

"In mid-I986, a world-class mining enterprise was created in British Columbia, bringing together the copper mining operations of Lornex Mining Corporation and Cominco into a new entity, Highland Valley Copper. This paper will focus on the background and rationalef or the formation of this partnership, the resulting operating changes and the productivity and cost benefits expected.IntroductionSince the deterioration of the world copper industry in 1981, the future of the Lomex and Cominco mines in the Highland Valley of British Columbia looked increasingly precarious. Despite the expansion of the Lomex mill complex in 1981 to one of the world's most cost-efficient copper and molybdenum concentrators, persistent low metal prices had made the remainder of the ore in the Lomex orebody marginally economic and had significantly foreshortened the expected life of the operation.Cominco had acquired the Bethlehem Copper assets in order to consolidate its ownership of the Valley orebody, and was feeding the Bethlehem concentrator with ore from the Valley orebody. In spite of the high grade and free-milling character of the Valley ore, profitability of the Cominco operation was severely restricted because of the limited capacity of the Bethlehem concentrator and its location high on the hillside above the orebody."

Jan 1, 1987

By Daniel Hodouin, Robert Lanthier, Yve Dube

"A procedure f or constructing a grinding mill dynamic model is proposed. This model is used in a dynamic simulator of are grinding circuits. The simulator is designed for flexible flow sheets involving different grinding mills and particle classifiers and is able to accept several single variable PID control loops. The dynamic model is validated on a laboratory ball mill, and calibrated to an industrial installation. The simulator is used for characterization of grinding circuit dynamic behaviour and tuning of control strategiesIntroductionThe ore grinding operation is a critical step of the ore preparation process because it is the last comminution stage before the separation of minerals. The properties of the ground minerals to be concentrated, control the quality and efficiency of the separation process. This is why it is important to control properly the operation of the last grinding stage, commonly constituted of a closed circuit ball mill with classifier . To provide an adequate fine product, the grinding operation should compensate for the perturbations of the feed characteristics (size analysis, grindability, etc.). The main objective is to maintain a constant size distribution for providing stable operating conditions to the separation units. Simultaneously another usual objective is to operate the grinding circuit at a maximum capacity.Automatic control applied to grinding circuit s is the appropriate approach to improve its operation. Most frequently average optimal operating conditions are determined from steady -state performances of the circuit , and the automatic control is used for stabilizing the operation at selected values of the process variables . In the traditional approach, one or several single input! single output (SISO) control loops are implemented and empirically tuned. Advanced control practices'!' are based on a quantitative analysis of the circuit dynamics, which could also give a basis for the tuning of conventional SISO 100ps(2)."

Jan 1, 1987

By Marc C. Bétournay

"Surface crown pillars, acting to safely protect underground workers and operations from surface elements, are recognized, herein, as distinct from conventional deeper underground pillars. Moreover, because of the variation in mining and geological conditions that exist from mine site to mine site, each case is viewed as unique. A review of numerous case studies and existing literature indicates that there is little general information or systematic problem-solving approach associated with them.A design process, not unlike that of other engineering disciplines, is presented to correct these deficiencies. As part of its purpose, it will inform operators of the key elements required for design and will address the problems of these appendages. The design, while taking into consideration possible surface crown pillar settings and inherent characteristics, is founded on a step-by-step procedure starting with site investigations through to monitoring or pillar recovery. The process is flexible, in that it incorporates decision making and changes in mining strategy. The purpose of each step is explained and each step is extensively described in terms of the required equipment and methods for field work, analysis and support measures. Analytical formulae and studies from several fields directly applicable to surface crown pillars are also given. Recommendations for future research studies are presented."

Jan 1, 1987

By E. Gervais

"In today's marketplace, heavy competition between materials is the norm. This is particularly true f or the base metals, which are being increasingly challenged by new or improved materials in all traditional applications. Current usage of base metals results from a combination of a metal's intrinsic properties, and technology. The future of the base metal industry rests with innovative, high-quality product development, its ability to take advantage of the results of worldwide, massive material R&D investments, and with the dynamism and effectiveness of its market development programs.The ZA casting alloys program is an illustration of the zinc industry’s efforts to protect and expand its market position in the casting field through state-of -the-art technological developments. The market potential f or these advanced engineering alloys is substantial, and their impact on traditional zinc die casting alloy consumption is particuarly important. The ZA alloys, in offering increased performance through zinc castings produced at low cost and by a wide range of moulding processes, have unlocked a multitude of new end-use applications.Following a review of the development of ZA alloys, of their key properties and of their performance characteristics, the numerous challenges that the alloys present to the zinc industry and to the R&D community are discussed.IntroductionZinc is anodic to steel and has a low, uniform rat e of corrosion; it has a low melting point, can be cast with precision , and is readily finished. In addition to its use in protecting steel and in the production of a wide range of castings, zinc is employed : (1) to produce brass, high-strength aluminum alloys and magnesium die casting alloys, (2) in the wrought state for coinage and in building products, particularly as roofing materials , and (3) as an oxide, in the rubber industry, in ceramics, glass, cosmetics, pharmaceutical products and as the starting materials for many chemicals.Zinc die castings are produced with accuracy at high speed, at low cost, are easily finished and have excel1ent mechnical properties . Car fuel economy, changes in automobile styling, competition from other materials, increased sophistication of design and miniaturization have all led to a dramatic change in the volume of zinc consumed for die-casting applications. This has been particularly notable in the United States. Throughout the 19505 and the I960s, casting was the fastest growing major use of zinc; it was firmly established, accounting for 35% of the total zinc consumption(1), By 1983, the volume of zinc being purchased for casting applications had dropped to less than 20% of all zinc consumed in the United States. In the western world(2), consumption for zinc casting application s is currently at about 15%; being nearly equal to the zinc consumed by the brass industry. Coating applications dominate with a consumption of more than 40% of the total market."

Jan 1, 1987

By G. Landry

"IntroductionThe Cape Breton Development Corporation (CBDC) is constantly searching for new technologies that will enhance the marketability of its coal. One technology which shows promise in utilizing Cape Breton coal while at the same time addressing the traditional problem of high sulphur inherent in the Sydney coalfield, is coal-water fuel (CWF).The CWF process incorporates a physical change of coal by grinding it to a flour-like consistency and then mixing additives with it to make a fine coal slurry. The result is a liquid dispersion of fine coal particles that looks like oil, stores and flows like oil but burns like coal. The equipment used in the CWF process is standard mineral processing equipment but application of the equipment to manufacture a specific coal particle size and the specified additives used in the mixing make it a unique technology.The product, which CBDC calls Carbofuel, consists of 70% coal, 29.5% water and 0.5% chemical additives. The key properties of the product are: (I) high solids loading, (2) medium viscosity levels, (3) stability against sedimentation, and (4) good atomization behaviour. Carbofuel specifications are presented in Table I. Carbofuel ProductionThe production of Carbofuel is based on the controlled processing of coal. This involves wet grinding of the coal to a specified fine size (-250 um), cleaning this fine product to remove mineral impurities and formulating (with chemical additives) a finalproduct from the cleaned coal. The flow diagram in Figure 1 indicates the processing circuit for Carbofuel production.CBDC operates a 7-tonne-per-hour continuous production plant complete with state-of-the-art control, full laboratory services, product storage and loadout facilities. The plant has operated since 1983 and has produced over 12000 tonnes for several major demonstrations. The plant is shown in Figure 2."

Jan 1, 1987

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By Bruce K. McKnight

"The new H-W orebody was evaluated by considering its production at three technically feasible rates. Capital and operating costs were estimated f or each rate and production sequences were established using mining cutoff limits generated by an ore value algorithm. The viability of the project was then examined by conducting economic and financial analyses of each of the three production cases under various world economic scenarios. These analyses employing standard profitability measures demonstrated all three cases would be economically viable; the production case which maximized the Net Present Value of the project was the one selected for development and production.IntroductionWestmin Resources Limited and its predecessor company, Western Mines Ltd., has been continuously carrying out mining operations near Myra Falls in Central Vancouver Island since December 1966. The mining operation, whose current production rate is approximately 830 tonnes / day (t/d), based on ore derived from the Myra and Lynx Mines, produces copper, lead and zinc concentrates which contain significant quantities of gold and silver in addition to the base metals.In the late 1970s, with Lynx and Myra ore reserves slipping to unacceptably low levels, a major increase in mine-site exploration was initiated, with outside geological staff brought in to complement the efforts of the mine's geological staff. By the end of 1979, this program had resulted in the discovery of a significant new orebody on a deeper horizon some 300 metres below the one which hosts the Lynx and Myra deposits. Throughout the period 1980-1982, major drilling was carried out to evaluate the new H-W deposit and by the end of 1982, drill-indicated mineral inventory for the deposit compared with Myra, Lynx and Price ore reserves was as shown in Table I. During this same three-year period, a major development and evaluation program was underway comprising environmental monitoring and control programs, shaft sinking test mining, bulk sampling and mill testing, rock mechanics studies and preparation of the Stage I and II reports for the multidisciplinary Environmental Land Use Committee (ELUC).As a result of the preliminary engineering work and exploration drilling, it became rapidly apparent that the H-W deposit could support a considerably higher production rate than the current one. Accordingly, engineering studies including scheduling of development and production as well as capital and operating cost estimates, were focused on three possible production rates: 1350, 1800 and 2700 t/d. Our task was to select the optimum one of these three rates."

Jan 1, 1987

By G. Halverson, K. Blower

"Giant Yellowknife Mines Limited (Giant) has been producing gold since 1948. Located at Yellowknife, Northwest Territories, Canada, see Figure 1, the mine processes approximately 1,200 short tons per day of 0.23 ounce gold per ton of ore.The majority of the gold in the ore is sub-microscopic and associated within the mineral arsenopyrite. This association complicates the extraction method since straight cyanidation will only recover 30% of the gold. The operations at Giant involve four essential steps, with an overall recovery of 87%. The steps shown in Figure 2 are crushing and grinding, flotation, roasting and cyanidation. These processes result in a number of effluent waste streams characterized in Table 1. These streams are combined and sent to a tailings storage pond for subsequent treatment prior to discharge to the environment.Giant is located just north of the 62nd parallel where winter temperatures drop to -40°C for extended periods. This entails storing effluent in dams over the seven month winter period for treatment during the relatively short summer season.The treatment method currently employed at Giant is an ""alkaline chlorination-arsenic precipitation-flocculation"" process. The pond water is subjected to three phases of treatment prior to being discharged to the environment as shown in Figure 3."

Jan 1, 1987

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By K. Wood, L. Duval

"The paper discusses the approach used to add a new, separate 5000 t/d copper-zinc treatment circuit to an existing, 1650 t/d copper circuit, essentially within the existing mill building. Temporary installation of new equipment allowed renovation and expansion within existing operating areas. Production in the original circuit was maintained at rated capacity throuqh0ut the construction period through close co-ordination between operating and construction groups. Downtime for circuit and service tie-ins was minimal. Both circuits are described briefly.For presentation at Canadian Mineral Processors Conference Ottawa, January, 1987.INTRODUCTIONLes Mines Selbaie is located in the Abitibi region of northwestern Quebec, in what has recently become better known as the Casa-Berardi-Joutel area. Les Mines Selbaie is operated as a joint venture project managed by Selca Division of BP Canada Inc. and owned 55% by BP Canada, 35% by Esso Minerals Canada and 10% by Trans Canada Pipelines."

Jan 1, 1987

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987