Search Documents

By Prasanta Paul, Aminul Islam

"Nhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area at Jawaharlal Nehru Port Terminal (JNPT), Uran, Maharashtra. The proposed container terminal yard is located on a recent reclamation on the Thane Creek, which was developed by land-based reclamation method. The underneath soft marine clay was treated, using vertical band drains and placement of surcharge upon.Settlement of the reclamation during its construction was monitored using settlement plate installed at +4.8m CD elevation which was above the highest high water level.This paper examines the settlement behaviour of the reclamation during the ground improvement works. The geotechnical parameters are back-analyzed by the authors from the field settlement results and the concerned preloading details. The back analyzed coefficients of consolidation due to horizontal flow (Ch) are compared with laboratory determined parameters and the estimated value, using Asaoka Method (1978). The authors also studied field compression ratio [CR= Cc/(1+e0)] vs. the compression ratio determined by laboratory test using back-analysis method.1. INTRODUCTIONNhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area of approximately 27 hectares, complete with associated buildings and services on a part brownfield/ greenfield site. The back-up area shall include a heavy duty block paved pavement with band beams for electric Rubber-Tyred Gantry Crane (eRTGC) alongwith surface water drainage system and other services including area lighting, provision of fire-fighting facilities , sources for potable water and power.Based on the Employer’s Requirement and the available geotechnical investigation report, ground improvement scheme is designed by the construction contractor. Ground improvement works included the installation of prefabricated vertical drains and subsequent placement of surcharge for accelerating the consolidation of the underlying soft marine clay."

Jan 1, 2015

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015

By Partha Sircar

"For Berth 22 modifications at the Port of Oakland, nearly 600 octagonal 24-inch ‘diameter’ precast-prestressed concrete piles were driven, some piles over 160 feet long. Prior to production pile driving, an indicator/test pile program was performed, which included extensive use of dynamic load testing with (Pile Driving Analyzer (PDA) & CAPWAP analyses. The indicator test-pile program resulted in requiring significantly longer piles than the original design based on subsurface borings. The cause of this discrepancy is investigated in light of the available geotechnical information, soil mechanics principles and standard techniques for pile capacity computations. Several interesting phenomena emerged. These include relatively low resistances offered by crushed rockfill than would conventionally be assumed, non-homogeneity of an apparently uniform formation and the effects of jetting on pile side friction. Also revealing was the significant increase in capacity between 1 and 3 weeks of driving for long piles in clay. Recommendations were developed for pile capacity for future use as “lessons learned”.IntroductionThe foundation for the replaced Berth 22 structure at the Port of Oakland in California involved driving approximately 570, 24-inch octagonal precast prestressed concrete piles. A plan and a section for the pile locations are presented in Figure 1.The ultimate loads on the piles used in the design are presented in Table 1 – the loads are quite heavy.The foundation design was followed by an extensive Indicator Pile Program. The contractors (Manson Construction Co. of Richmond, California) opted to use a Delmag D62-02 diesel hammer (Rated Maximum Energy – 165 kip-feet). Per the project specifications, the same hammer was used for both indicator and production pile driving. The production piles of appropriate lengths were ordered based on thr results of the Indicator Pile Program. A number of interesting results were found from the Indicator Program, which is discussed in this paper."

Jan 1, 2015

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015

By Unnikrishnan Nair, Sandeep S. Nikam, Sanjay D. Patil, Prabir C. Basu

"Mumbai Metropolitan Region Development Authority (MMRDA) entrusted to implement Monorail Systems in various parts of Mumbai Metropolitan Region (MMR) with the objective to supplement the present transport system in MMR. The stretch of Monorail is starting from Sant Gadge Maharaj Chowk (SGMC) and extending up to Chembur Railway Station, divided into 2 phases. Construction of Phase 1 (Chembur to Wadala Depot) is complete and Phase 2 (Wadala Depot to SGMC) is under construction.Monorail runs on prestressed girder (guide beam) of span ranging from 20m to 28m supported on pier founded upon group of end bearing piles embedded in rock, pile group ranging from 2-4 piles of diameter 1000mm each.For the purpose of site characterization, geo-technical investigations were carried out along the alignment of Monorail system as mentioned above. These investigations included field and laboratory tests. The subsurface strata mainly consist of silty sand, gravel, underlain by marine clay extending up to stronger basalt rock with volcanic breccia. Overburden consisting of mainly marine clay ranging from 5.5m to 11m at all locations within the influence zone of settlement.The existing rigid pavement along of Sion-Koliwada and Anik-Wadala were constructed about 5 years prior to the construction of Monorail piers. Before laying the rigid pavement, to improve the geotechnical strength of subsoil (mainly marine clay), ground improvement using stone columns was undertaken by MMRDA. In light of limited right of way, the Monorail piers have been constructed in the median portion of the road. The line became operational on February 2014, in few months it was noticed that, in the vicinity of the Monorail piers, along Sion-Koliwada link and Anik-Wadala link, the Road Pavement Quality Concrete (PQC) panels adjacent to the Monorail piers started showing distress in form of nonuniform settlement of the concrete panels.Effect of pile foundation on pavements/PQC slab distress and possible causes of distress were investigated. Initially the distress was thought to be upheaval of monorail pier cap, but further investigations revealed the same to be soil settlement occurring over time. This paper describes the investigation carried out for identifying the cause of this settlement."

Jan 1, 2015

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By Jianhua Wang, Jianming Yao, Zhen Meng, Jinjian Chen

"Drilled screw pile is a newly developed displacement pile foundation which has been applied in soft clay for many years. Compared with traditional circular displacement pile, It is characterized by high bearing capacity, small volume and small squeezing effects. For the purpose of investigating the squeezing effects of drilled screw pile, a full scale field monitoring test with two test piles was performed. Detailed soil horizontal displacement and pore pressure measurements were conducted in the vicinity of the two drilled screw piles during penetration and subsequent soil consolidation. It can be concluded that the horizontal displacement of the surrounding soil induced by the installation of a drilled screw pile is mainly in a circular region with a diameter of 3 m (r/D<6), and the compaction effect outside the area can be essentially negligible; The excess pore pressures measured at the same time increase with depth throughout the entire process of consolidation, and its dissipation shows an exponential decay as a function of time.INTRODUCTIONA knowledge of the displacement and stress changes induced in the soil surrounding a pile is very important for evaluating pile performance. Numerous field and laboratory research projects have examined loading conditions, total soil stresses, and excess pore pressures during and following pile installation (Pestana et al., 2002). A relatively comprehensive and detailed review of these experimental works from 1948 to 2002 was presented by Pestana et al. (2002). More recently, Xu et al. (2006) conducted a field experiment to study displacements and stresses in the vicinity of two pipe piles during their installation in a soft lightly overconsolidated clay and compared the field measurements with existing predictive methods. Abdrabbo and Gaaver (2011) collected field observation data from four different construction sites to study soil disturbance during construction of piles using continuous flight auger (CFA). They have found that the disturbed zone of soil by CFA has a conical shape and the excess pore pressure has no appreciable influence on the load capacity of the piles.Drilled screw pile (DS pile) is a kind of vibration-free, cast-in-place concrete pile. Because of the excellent bearing performance, low level of vibration pollution and negligible spoil, as well as its fast construction speed, DS pile has been widely accepted by many engineers around the world. As a new type of drilled displacement pile, the significant installation effects of DS pile on the adjacent soil have not been systematically and integrally investigated yet. Since a proper numerical simulation of the real installation process of DS pile is difficult to achieve, the investigation based on field measurements is necessary. This paper presents a field investigation of the installation effects of two DS piles on surrounding soils. Detailed horizontal soil displacement and pore pressure measurements during pile installation and subsequent soil consolidation have been conducted. Based on the monitoring data, variation of horizontal displacements and dissipation of excess pore pressures with depth and time have been analyzed. What's more, the construction machinery and technology used in DS pile installation are also simply introduced."

Jan 1, 2015

By Tsunenobu Nozaki

"Basically, the “Press-in Piling Method” was invented to eliminate construction nuisances, such as noise and vibration which have been serious unsolved problems for advancing societies over a long time. In the construction industry, piling works have been a major cause of noise and vibration, because most piling methods utilize dynamic load to install piles into the ground. The secret of the Press-in Piling Method is to utilize static loading to install pre-formed piles rather than dynamic load. The piles are hydraulically gripped and jacked into the ground by the special piling rig known as the “Silent Piler”. Therefore, the piles can form a robust and firm foundation, which is another advantage of the Press-in Piling Method.The Press-in Piling Mechanism and Implant Foundations The basis of the Press-in Piling Method is simple. The Pres-in Piling Machine installs a preformed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles, which are called “Reaction Piles”. Due to this, the Press-in Piling Machine can produce a powerful piling force whilst only requiring minimal machine size.With the Press-in Piling Method, as piles are pressed into the ground, they are incorporated with the surrounding soils, which provides a large bearing capacity and passive horizontal resistance. These embedded foundations which are firmly anchored into the ground are known as “Implant Foundations”. Being embedded into the ground, the foundations are resilient and maintain their serviceability even in the worst credible design conditions."

Jan 1, 2015

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By Seth H. Hamblin, John E. Regan, Dimitrios Palantzas

"Through reliability-based calibration of larger pile load test databases, recent developments of the Load Resistance Factor Design (LRFD) methods, which include geotechnical load and resistance factors for deep foundations design, have advanced the state of practice for geotechnical engineering. These load test databases upon which the current geotechnical load and resistance factors have been developed are limited, however, and do not provide sufficient data to support the development of resistance factors for uplift (tension) pile capacity. As such, some recommended resistance factors for uplift capacity estimation methods are simply derived by reducing the recommended resistance factors for piles in compression by a factor of 0.10.The results of three (3) tension loading tests performed to failure on 508 mm (20- in) square precast, prestressed concrete piles, driven though granular soil in southeastern Massachusetts, are presented and compared to static pile capacity calculations and dynamic analyses performed using the Pile Driving Analyzer (PDA) during installation. These results are presented along with current recommended LRFD resistance factors for driven piles under uplift (tension) loading conditions. These comparisons offer an assessment of the applicability and limitations of current resistance factors methods for piles under uplift loading and may be useful additions to the existing database for future calibrations of LRFD resistance factors for driven prestressed concrete piles in sand.IntroductionIn 2010, two (2) natural draft cooling towers were constructed by Kiewit (Kiewit) Construction Company of Woodcliff Lake, New Jersey at the Brayton Point Power Station in Somerset, Massachusetts. These massive 500 foot tall, 400 foot diameter cooling towers were designed to convert the existing “open loop” system into a “closed loop system” thereby dramatically reducing the thermal impact to Mt. Hope Bay.Based on design guidance from the German VBG Design Code and the Massachusetts State Building Code (MSBC), tension (i.e. uplift) and lateral loads due to wind loads and design seismic events represented the critical loading conditions.Weighing approximately 190,000 kips upon completion, the cooling tower loads are transferred to 44 foundation nodes (i.e. pile caps) evenly spaced along ring beams which run the circular perimeter of each tower base. Each pile cap node was designed to resist a 2,000 ton compression load, 200 tons in tension (i.e. uplift), and 600 tons in the lateral direction."

Jan 1, 2015

By Deepak Pappusetty, Miguel A. Pando

This study is motivated from the increased interest in recent years to explore use of Ocean Energy Converters (OEC’s).OEC’s can be tidal or generate electricity from wave or current action. Design of foundation systems for these OEC’s is a key consideration as it can represent about 35% of the initial installation cost. The primary focus of this paper is related to foundation systems involving monopiles where a key design consideration includes gradual accumulation of pile head deformations beyond serviceability limits of the OEC. This design consideration is important since these foundation systems are often subjected to more than 108 low amplitude repetitive dynamic load cycles during a normal 30 year design life. Research on single model piles installed in sand and subjected to over 104 low amplitude lateral load cycles have shown that pile head displacements and rotations tend to increase gradually with increasing load cycles. This gradual development of pile head deformation is related to plastic strain accumulation in the soil in the vicinity of the monopile. Analytical methodologies based on conventional p-y curves typically cannot predict these accumulated pile head rotations and displacements. Even 3D dynamic Finite Element Analyses may not capture this response for several conventionally used soil constitutive models. This manuscript presents predictions using p-y based methods as well as 3D dynamic finite element analyses. The different numerical predictions are compared to available experimental data. Results from this study show that conventional p-y methods do not predict the gradual pile head displacements observed experimentally. Modified p-y curves, developed for cyclic loading, do a better job than conventional p-y curves but tend to greatly under predict deformation. This is believed to be related to the cyclic load test data used to develop these cyclic p-y curves which involved at most up to 500 cycles and did not include high frequency contents or partial unloading cycles. The 3D FEA captured reasonably well the general observed trends of gradual accumulation of pile head rotation and lateral deformation with increasing constant amplitude lateral load cycles.

Jan 1, 2015

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

By Sumit Kumar Biswas, Moyukh De, Sibapriya Mukherjee

"The piles often are also subjected to lateral (horizontal) forces and moments. In fact, there are some structures where the primary function of piles is to transfer lateral loads to the ground. Proper analysis of laterally loaded piles is very important to the geotechnical and civil engineering profession.In the present investigation an experimental study has been carried out with free head short model cast iron hollow piles of outer diameter of 24 mm and L/d ratios of 8, 10, and 15. The experimental results have been supplemented by numerical techniques using PLAXIS-3D Foundation version 2.1 software. The results have been found to agree reasonably well with the experimental results. Further finite difference approach has been adoptedto reduce the computational time and to calculate the coefficient of modulus of subgrade reaction (?h) from the load- deflection data obtained from PLAXIS output at different pile depths. The parametric study has been extended for the non-dimensional form defined as flexibility ratio (F.R.),where ?h, L, Ep and Ip are the coefficient of modulus of sub-grade reaction, the embeddedlength of model pile, elastic modulus of pile material and the moment of inertia of model pile about the central axis respectively).The variation of coefficient of horizontal modulus of sub-grade reaction (?h) has been studied with respect to the following parameters for homogeneous soil system: relative density andL/d ratio. It has been found that the logarithm of flexibility ratio increases with increase inrelative density and increase inL/d Ratio. The values of ?h obtained by the proposed method have been, found to be close to the numerical results.As output of this research, graphs have been generated in respect of different parametric variations to gain an insight into behavior of piles under lateral load for short piles."

Jan 1, 2015

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

By Mark Spence, Tom Lardner, Matthew Janes

"IntroductionThe design-build method streamlines project delivery through a single contract between the Contract manager and the design-build team. The design-build method places emphasis on collaborative project management between design and construction disciplines to minimize project schedule, reduce costs, encourage balance risk amongst the design-build team. Since 1985, the percentage of nonresidential design and construction projects has increased from 5% to 45%.1A project carried out in Edmonton, Alberta, Canada will be used as an example to illustrate the challenges of the design-build project delivery method and the merits of establishing a GBR. The project involved a complex slope stabilization as part of an extensive freeway widening. At the project location the roadway was being widened within the base of a historic stream valley into a steep slope with a history of a previous slope failure. The slope was to be steepened through the installation of a series of 14 interlocking arc structures constructed half way up the slope. Access and schedule proved critical to the successful completion of the project.Geotechnique and Site HistoryThe geotechnical investigation undertaken for the site included six boreholes drilled at the crest of the slope to depths ranging from 14.5 m to 30.2 m. Laboratory testing of the soil samples included direct shear tests, Atterberg limits and grain size analysis. The geotechnical report also referenced a previous geotechnical investigation that was carried out in response to a failure of the slope in 1971."

Jan 1, 2015

By Sumantra Sengupta

"Northeast Frontier Railway (NF Railway) intends to connect Imphal, the capital of Manipur (bordering Myanmar) with Assam by railway link. They have planned a 125km long railway line that passes through steep rolling hills of Patkai region, eastern trail of Himalaya, and as a result large number of tunnels and bridges need to be designed. While the high mountains are penetrated by tunnel, the deep gorges between the mountain ridges are connected by tall bridges. The tallest of such bridges connects a gorge at about 140m above its bed level with an overall length about 700m at rail level. In all, five such bridges with tall piers are now under construction. With extensive study on possible alternate arrangement of the bridges considering the effect of high seismicity of the area, moderately to highly weathered siltstone/ sandstone as ground bed material, slope of the hills etc it was decided that bridge will be founded on 1.5m diameter bored cast in situ piles with length varying from 20m to 30m depending on the location. The substructures are RCC hollow pier and superstructures are steel open web through type girder of 103.5m span. Considering absence of any major construction work in the vicinity, it was decided that prior to design work, Site-specific spectrum study will be carried out and design will be carried out considering the varying stiffness of the tall piers, each of different height. Interesting results were obtained regarding behavior of piles under lateral loads generated by high seismic conditions. The paper discusses in detail the design of Pile foundations and the effect of bed material along the steep slope on which the piles are being constructed.INTRODUCTIONIndian Railway has undertaken the construction work of connecting the North-Eastern states of India through railway line. The major stretches of the area passes through hilly terrain and as a result the line passes through tunnels and bridges in succession. The tall mountains are being penetrated with tunnels and immediate after deep gorges are crossed with high level bridges. The entire area is under high seismically active zone. The bed material below the ground level of the sloped hill is 4 to 10 meter of mixed soil of sand, gravel, pebbles etc underlain by moderately to highly weathered sandstone, siltstone at the higher level and moderately weathered sandstone, siltstone at lower level. Considering all the aspects like constructability, maintainability, geological and geotechnical aspect, seismicity, stability, safety, functional aspect and cost it was finally decided that the bridges will be simply supported structure with open web through type steel superstructure of maximum span 103.5m and hollow cylindrical discretely varying RCC substructure with 1.5m diameter group of piles as foundation. The paper discusses on the design aspect of the pile foundation in the rocky strata in the hill slope. The codes and standards that have been followed for design are IRS (Indian Railway Standard), IS (Indian Standard), IRC (Indian Road Congress), AREMA (American Railway Engineering and Maintenance-of-way Association), UIC (International Union of Railway) provisions."

Jan 1, 2015