Search Documents

By Yong Pan, Purushotham Tukkaraja

Block caving is a preferred underground mining technique due to its high production rate and low operation cost. Before its final step into a mature caving system using gravity to break rock, drilling and blasting are required to form drawbells to connect the production level and undercut level and induce the initial caving propagation in undercut level. A large amount of toxic fume generated by blasting activities poses a big threat to people working in a confined environment and ventilation is assumed to be the most economical and efficient way to deal with this issue. Past research shows that it’s common to use traditional methods like using a formula or using numerical method (Computational Fluid Dynamic (CFD)) simulation to predict re-entry time after each blasting, but it fails to consider the percentage of toxic fume entrapped in muckpile, which could reach up to 70%. In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

By Yong Pan, Purushotham Tukkaraja

In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

Feb 1, 2020

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By J S. Kuszmaul

The economic development of modified in situ oil shale retorting will benefit from the ability to design a blasting scheme that creates a rubble bed of uniform permeability. Preparing such a design depends upon successfully predicting how a given explosive will break rock. Numerical models are used to make predictions of the extent of damage caused by an explosion.

Jan 1, 1985

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By A. S. Tawadrous

The stress field around a detonating charge in a borehole was calculated using AUTODYN for a variety of in-situ stress conditions. Calculations were conducted for zero in-situ stress, hydrostatic conditions at 100MPa, uniaxial stress conditions of 100MPa, and bi-axial state of stress with amplitudes of 200MPa and 100MPa along the axes. Two different explosives, ANFO and emulsion, were used for the calculations. It was shown that in-situ stress fields had an effect on the tensile and compressional damage zones around the blasthole, calculated on the basis of the maximum amplitude of the stress pulses in the rock after the detonation of the explosive in the blasthole. The extent of compressional damage increased around the borehole, whereas, the extent of the tensile damage decreased. The damage zones are of elliptical nature with their axes parallel to the direction of the principal stresses. The difference between the major and minor axis of the elliptical damage was not very significant in the case of the compressional damage; however it was significant in the case of the tensile damage.

Jan 1, 2007

By Andrew Theobald, Peter Dare-Bryan, Trevor Byers

The use of advanced modelling techniques and the timing flexibility of electronic initiation systems allows for unprecedented control over blast outcomes as shown in several complex blasting problems experienced by the open pit operation Xstrata Ernest Henry Mine (EHM) in north-west Queensland, Australia.

Jan 1, 2010

By Huang Fenglei, Jin Qiankun

A new linear charge method has been applied in coyote blasting for highway excavation in which presplitting boreholes are set along the designed rock slope with some empty chambers at the end of linear charges whose axes are perpendicular to the axis of the highway. Three-dimensional nonlinear finite element analysis for this method has been conducted using LS-DYNA3D. The results indicate that the blasting damage to the rock slope is reduced greatly using the new linear charge method in coyote blasting.

Jan 1, 1998

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By C H. Ryu

This paper presents a simplified two-dimensional numerical model of block fragmentation in a Jointed rock mass during the late or throw stage of a blast after wave effects have subsided. The model is based on the distinct element method. Examples illustrate the approach and allow for a comparison of effects of Joint patterns on fragmentation and resulting block motion.

Jan 1, 1986

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By Mark S. Rayson, Jessy Lee, David O. Johnson, Matthew R. Rawls

The ability to manipulate the structure of liquid chemicals in an explosive is important in mining applications, where precision blasting is crucial for the safe, reliable, economical and eco-friendly extraction of ores. Static mixers allow explosives, emulsion-based in particular, to be custom-made as they offer precise and reproducible mixing without the need for moving mechanical parts. In this paper, we perform numerical simulations on the laminar mixing of two nitrate-based fluids in a Kenics static mixer unit for various mixer parameters. Two numerical methods were investigated in the study of the mixing pattern: solving the mass transfer equation and using particle tracking. The former introduces artificial numerical diffusion which can lead to spurious smearing of the component boundaries, a problem that can be avoided with the latter technique. We have also demonstrated that the particle tracing method is capable of qualitatively predicting the blending patterns under the conditions studied.

Jan 1, 2014

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Alan Hooper, James E. Mischler

Construction began in 1984 for a 5 megawatt hydroelectric power retrofit at the O'Shaughnessy Dam for the City of Columbus, Ohio. The construction necessitated excavation of limestone bedrock up to 27 feet below the normal water level of the river downstream of the dam. Proximity to the river and difficult terrain resulted in an interesting and challenging construction project.

Jan 1, 1986

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

Test blasting was carried out to study the flying characteristics of rock mass caused in bench blasting. The quantity of explosives was increased from 7.6kg to 9.1kg and the Minimum burden was changed from 131mm to 451mm. The effect of condition for the characteristics of fly rock were considered. The fly rock was observed using the high-speed camera and video to study the flying characteristics of the rock mass caused in the bench blasting. Numerical simulation of fly rock was carried out using DDA (Discontinuous Deformation Analysis) method. It was clear that the DDA method can be applied in the simulation of fly rock caused in bench blasting.

Jan 1, 1997

By John W. Kopp

The U. S. Bureau of Mines investigated flyrock and burden movement from blasting at several limestone and basalt quarries in the upper midwest. Blasts have been studied at 14 different sites using high-speed cinematography. Blasting was accomplished in 75- and 150-mmdiameter holes using a variety of explosives. Films from each blast were analyzed to show burden velocities, observed flyrock distance, and direction of throw in relation to the shot layout. This technique, in some cases, allowed determining point of origin and cause of the flyrock as well as the flyrock range.

Jan 1, 1994

By Deane Tunaley, Paul Tidman, Qian Liu, John Mullay

Laboratory studies have indicated that the crystallization and desensitization of microballoon sensitized emulsion explosives start immediately after shocking or pre-compression. However, the question of whether or not the shocked emulsion could be worsened by the growth of crystallization or recovered by rebounding back to lower densities has been rarely examined under actual rock blasting conditions. This study was primarily intended to investigate the desensitization characteristics of two commonly used emulsion products in terms of blasthole spacing and delay duration. In the experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1995

By David Leidel, James Stuart

The 50 ohm resistorized electric detonator is commonly used in the oilfield for initiation of wireline conveyed perforating guns and other downhole explosive tools. This type of electric detonator provides some degree of safety above that of the conventional one ohm electric detonator, since a higher current level is required to initiate the device. In order to obtain the necessary data to develop safe distance tables from RF sources for the 50 ohm electric detonator, laboratory tests were conducted to determine the detonator’s “no-fire” current, AC impedance, and its susceptibility to ESD. The results were surprising as two types of failure modes were observed. The “no-fire’ current levels determined from Langlie “One-Shot” Test Methods were determined for the devices tested providing values for the 0.999 probability “no-fire” power level at a 95% confidence level. This data will serve as the basis for sets of safe distance tables from RF sources that will appear in the forthcoming edition of the Institute of Makers of Explosives Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators, (Blasting Caps)”.

Jan 1, 2010

This paper presents a brief discussion of three case histories to illustrate several aspects of the question of blasting in or immediately adjacent to concrete. The results demonstrate a need to make dramatic upward revisions in previous criteria, whether it be the standard particle velocity criteria or damage response spectra bounds, - especially those which include conservative upper limits of constant acceleration for the high-frequency portion of the spectrum. It is demonstrated, also, that conventional off-the-shelf blast-monitoring instruments are not capable of monitoring small blasts at close range. Both the frequencies and the levels of effect are beyond the range of such instruments. These case histories suggest further that there is a need to review the applicability of certain wellknown equations of elasticity.

Jan 1, 1980

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981