Search Documents

By Q Liu, P D. Katsabanis

Dust explosions in underground sulphide and oil shale mines result from the detonation of explosives in the blasting operations. Explosive composition, oxygen balance, priming and ideality of detonation were examined theoretically and experimentally in the presence of reactive sulphide dust. It was found that the temperature as well as the chemical composition of the gaseous products of detonation are the controlling parameters related to the explosive. Non aluminized, oxygen balanced emulsion explosives were proven to be relatively safe, while explosives creating combustible products were proven to be extremely dangerous due to the secondary flame they generate. Since a large number of dusty orebodies are often very friable, low density emulsion explosives are also examined for application in production blasting.

Jan 1, 1991

By Andrew F. McKown

This paper will discuss the mechanisms of potential damage from close-in construction blasting, concentrating on two mechanisms: elastic ground vibrations and non-elastic (permanent) ground deformations. The latter will be shown to be the most dangerous for close-in blasting. With respect to elastic ground vibrations, discussion will center on the differences in vibration frequencies and impacts between typical close-in construction blasting and typical mine and quarry blasts, and how using vibration criteria derived for residential structures near mines can lead to very conservative criteria for close-in construction blasting. The effects of high frequency vibrations seen in close-in blasting will be commented on. Factors affecting the magnitude of ground motions will be discussed. Simple, practical techniques will be presented to minimize the potential for damage from close-in blasting, by minimizing the potential for rock block movement or ground heave. Case histories will be presented to illustrate some of the techniques discussed, and give examples of successful close-in blasting projects.

Jan 1, 1991

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By J P. F Warkentin, A W. Bauer

Recently, significant improvements have been made in both blast design methods and blasting accessories. The introduction of extremely accurate blast delays now allows proper implementation of advanced blast designs. Thus the onus for future blasting improvements has moved from blast design to the need for ensuring that explosives quality is of the highest order. One measurement commonly used to assess explosive performance is the velocity of detonation (VOD).

Jan 1, 1991

By J Lyall Workman, Peter N. Calder

Operations using draglines to remove the overburden above coal seams have increasingly turned to cast blasting to improve productivity and reduce costs. Many such operations also employ active highwall pre- splitting to produce highwalls of well defined configuration, behind which the subsequent blast can be designed and implemented to maximize casting. In some cases isolating the block to be blasted allows water to drain out of the rock mass and provides the opportunity to use less costly explosives.

Jan 1, 1991

By Randall M. Wheeler

The purpose of this workshop is to illustrate how computer software can be used to evaluate blast design timing and simulate probable vibration characteristics. The workshop will be presented in two parts. Part I will cover the COMPU-BLAST Blast Design and Timing Analysis Program. Part II will focus on the ALPHA-BUST Vibration Analysis and Waveform Simulation Program. The information presented in the workshop will show how these two programs can be used together to help plan blast designs and aid in the control of vibration effects.

Jan 1, 1991

By Gordon F. Revey

Hanging Lake Joint Venture recently excavated two conventional 42 foot diameter highway tunnels in the difficult ground conditions of Glenwood Canyon, Colorado. This paper outlines the type and success of the various Controlled Blasting Techniques that were used to minimize overbreak in the portal and tunnel excavations. The different Smoothwall and Cushion Charge loads used in the different ground types are described in detail. Delay Timing and Drilling Pattern variations are also discussed.

Jan 1, 1991

By Daniel Moroz

This paper will provide an informative overview of the types of explosives and the various methods employed to control avalanches within the boundaries of major ski resorts.

Jan 1, 1991

By Michael S. Wieland, Thomas C. Ruhe

Marginal detonation of explosives can produce more toxic fumes with higher nitrogen oxides (NOx) than normal detonation. In delay blasting, shock waves from borehole charge explosions can impact those delayed charges still remaining in the delay pattern. This can result in partial desensitization, whereupon the explosive does not misfire, but detonates in a weak unstable fashion releasing a different/unusual spectrum of gaseous reaction products.

Jan 1, 1991

This paper is concerned with the blasting of rock in mining. The most common purpose of blasting rock is to cast it or to disrupt its structure sufficiently for effective digging and subsequent removal.

Jan 1, 1991

By Paul V. Sterk

In the early 1980's, the Homestake Mine converted from labor intensive methods such as open cut-and-fill mining to Vertical Crater Retreat (\/CR) bulk mining and mechanized cut and fill. This transformation occurred as a result of high costs and low productivity associated with open cut-and-fill mining. Use of Vertical Crater Retreat allowed Homestake to contain waste development rock within the mine to further decrease costs since the voids created from VCR stopes provide a good receptacle. The need to access these voids from surrounding development to facilitate waste dumping precipitated the development of drop raising. This system is cheaper than raise boring because it allows drilling into the top of an open stope without the expense of raise boring cutouts or equipment. It's safer than conventional raising since access from the bottom is not required. Two methods of long hole raising or "drop" raising have been successfully developed at the Homestake Mine and can be categorized as Ring Drill Drop Raising using 2-1/4 inch holes and VCR Drop Raising using 6-1/2 inch holes.

Jan 1, 1991

By J Lyall Workman, Larry R. Fletcher

Blasting methods have been proposed for reclaiming abandoned underground coal mine sites having unstable conditions. The objective of blasting is twofold: the permanent stabilization of an area by the collapse of underground workings to prevent any future subsidence, and the use of blasting to close existing sinkholes.

Jan 1, 1991

By A T. Spathis, J J. Felice, T A. Beattie

High speed cinematography of surface blasting operations is used for diagnosing various aspects of blast performance. Several quantitative features may be derived including confirmation of the hole initiation sequence, time to first movement, evidence of stemming ejection and measurements of face velocity. Face velocity measurements using high speed cinematography have the following disadvantages: firstly, for accurate measurements placement of targets on the face and surveying of them is necessary; secondly, the analysis requires experience and time and can only be done after the film has been developed.

Jan 1, 1991

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By Mike D. J Bonneau, Malcom Jr Ford

Rietspruit Opencast Services was one of the first opencast coal mines to successfully employ cast blasting to aid in the burden removal operation. Initial work on cast blasting began at the mine in 1980 and has developed to a stage where approximately 26% of the total burden material is cast to a point where handling by draglines is no longer required.

Jan 1, 1991

By Roy Rose, Bruce Bowles, Wesley L. Bender

Numerous large diameter water wells are used to dewater the pit at the Sleeper Mine. Occasionally, a well will be located inside the boundaries of a blast. Although one might expect that wells so located would become inoperable due to blast-induced damage, in most instances this has not proven to be the case.

Jan 1, 1991

By Tim A. Beattie, John R. Grant, David L. Kennedy

After many years of research, ICI staff have developed a numerical modelling system for the study of detonator/primer/explosive configurations. Results from this work clearly identified that current primer designs were not as effective in delivering their energy potential as needed. Alternative designs were evaluated and several prototypes, all essentially spherical in shape, were built for testing. Results have shown a significant improvement in various aspects of primer performance, including omni-directional pressure transferral and increased energy release rates. Reliable, high performance priming of explosives is now achievable for a much wider application range.

Jan 1, 1991

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By L D. Santis, L Wardrip

This paper begins with a summary of the development of the sheathed explosive charge from it's conception by the Bureau of Mines in 1981 through the evaluation of its safety, culminating in revisions to the Code of Federal Regulations (CFR), Title 30, Parts 15 and 75 which provide for its approval as a permissible explosive and safe use in underground coal mines. In 1989, Austin Powder Company decided to market a sheathed charge and proceeded to develop a commercial version which they call the Rock*Buster. The Rock*Buster was tested by the Bureau of Mines and subsequently approved as a permissible sheathed explosive unit by the Mine Safety and Health Administration (MSHA). Marketing of the Rock*Buster began in the Spring of 1990. In May 1990, the Rock*Buster was first used in an underground coal mine, Jim Walter Resources' (JWR) No. 4 Mine in Brookwood, AL. Trials with Austin's units were impressive. Representatives from MSHA, the State of Alabama, JWR, the United Mine Workers, and other local mining companies observed the charge break large boulders on the surface. Later, the charges were used underground to break large rocks from a roof fall that were obstructing ventilation. During its first week on the job, the Rock*Buster reduced the downtime experienced on JWR's longwall sections by quickly taking care of problem roof falls which halt operations.

Jan 1, 1991

By Brian Gar Wingfield

Bulk explosive systems have developed from the infancy stages in the early sixties to a sophisticated process of the nineties. With ever changing bulk explosives technology, bulk delivery and loading systems needed to keep pace. Efficiency, as compared with packaged loading, was the keyword allowing faster loading of trucks and shots. Efficiency was also improved by the explosives coupling factor that bulk loading permitted.

Jan 1, 1991