Search Documents

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By Ernest J. Conway

Seventy-four human factors research and development projects were identified for possible Bureau funding. The projects were based on (1) literature surveys, (2) reviews of accident statistics and reports, (3) interviews with equipment manufacturers, MSHA, and Bureau personnel, and (4) site visits to 26 mines. The projects are divided into the following categories: those related to (1) mobile equipment, (2) maintenance shops and areas, (3) plants and mills, (4) organizational factors, (5) safety programs/data, and (6) training. The projects were rated by industry and MSHA people in terms of benefit to the industry. Projects were placed into three categories of priority. The highest priority contained 25 projects with 26 in Category 2, and 23 projects in the lowest category.

Jan 1, 1982

By Jerry A. Wichser

A series of linear programmed instruction modules was developed in the general subject areas of Blasting Technology & Explosives Safety & Electrical Training. The linear programs (modules) were developed in the form of tape-slide plus workbook materials, while the branching format evolved from the LTS teaching machine system from MIT, through several other teaching machines and micro-computers, finally settling on Radio Shack TRS-80 microcomputers, Models I & III. Initial validation figures indicate that essentially the same result, are attained from both methods (based on pre and post test scores), with the most noticeable difference being an approximately 25% savings in study time with the branching modules. In December 1980, the development of modules on High-Voltage Training, Trolley Wireman Training, and Compressed Gas Safety was added to the overall tasks of the contract.

Jan 1, 1984

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By James W. Martin

This user?s manual analyzes the application, selection and performance of hopper/crusher/conveyor systems used with front-end loaders in surface mining operations. It is designed to be used in conjunction with its companion manual: "Guideline Manual for Front-End Loader Load-and-Carry Applications" Aspects of the application are covered as well as design considerations of the hopper/crusher/conveyor units. Lists of equipment manufacturers, crusher specifications, together with a series of checklists, are included for preliminary analysis.

Jan 1, 1982

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By James C. Barker

The U. S. Bureau of Mines made a reconnaissance In the western Crazy Mountains for cobalt and associated metals as part of the Alaska-wide critical and strategic metals program. The area, located about 75 miles north of Fairbanks in central Alaska, is underlain by complexly faulted, predominantly clastic sedimentary rocks bordering the Tintina Fault system. Above background metal concentrations were found to occur in altered fault zones, tectonic breccias, soils, and ground water seeps and precipitates that either cut or are derived from the faulted clastic sedimentary rocks. Up to 0.115 pct cobalt and more than 2.0 pct zinc were detected in soil samples. Spring precipitates contained up to 1.3 pct zinc, 0.037 pct tungsten, and other metals. Some localities lacked cobalt but contained anomalous amounts of copper, lead, zinc, silver, and other metals. No outcropping of primary metallic minerals was located because of Colluvium and vegetation cover and extensive deep leaching. Therefore, whether the metal values encountered are due to primary deposits with economic development potential or are the results of concentration by ground water from low-grade sources is unknown. The presence of cobalt, nickel and zinc, and the identification of minor tin and tungsten indicate that further investigation is warranted.

Jan 1, 1983

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By J. F. McCoy

The quantitative determination of the mass rate of flow of methane in an underground airway is calculated as the product of the methane concentration and the air flow rate. Velocities are taken at several points and then averaged over the airway cross section to determine the total volume flow. Errors in velocity measurement thereby result in errors in total volume flow as well as the mass flow rate of methane. The purpose of this program was to evaluate existing instrumentation for measuring air velocities in the speed range under 2000 feet per minute; to evaluate the method for determining total air volume flow from the velocity measurements; to evaluate new techniques which may be applied to measuring air velocities; and to design a prototype instrument which represents the best technique based on the evaluation. The instrument should be: a. portable b. self-contained c. insensitive to dust, moisture and temperature changes d. safe for use in gassy mines

Jan 1, 1972

This report summarizes the results of a research project entitled "Fatal Accident Data Base Development." This project is the last project under Contract No. S0110601. Volumes I and 1I, "Industrial Engineering Study of Hazards Associated with Underground Coat Mine Production," summarize the original industrial engineering project and the Fatal Accident Report Analysis project. These projects were completed and accepted by the U.S. Bureau of Mines on December 10, 1971. Both volumes of the report have been made available by the Bureau to the public through the U. S. Department of Commerce technical information service. Another project under the same con tract, entitled "Equipment Operations Safety Study, ' was completed in January 1972 and the report was accepted by the U. S. B. M. at that time. The analysis in this Natal Accident. Data Lose Development report is closely related to analysis in both of the earlier reports. The original project involved an industrial engineering and safety of production operations for a representative sample of underground bituminous coal mines. The contactor was required to make recommendations 'in work practices, mining methods, equipment, and safety practices which can effectively reduce the fatality rate from rib and roof falls.' (Longwall mining methods were excluded from the study.) Time study and work element analyses were performed in over 50 mines as part of the field data gathering effort. Another requirement of the study was to develop sets of multiflow. Process charts, which are diagrammatic illustrations of the time-related interaction of mining, cycle job elements.

Jan 1, 1972

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By Carlie E. Banks

Tasks during Phase I of this contract effort were performed in four principal functional areas. These were geology, hydrology, reclamation and mining. Data were gathered from literature reviews, mine visits, survey of manufacturers, consultation with government agencies, and unpublished or private communications with contractors and consultants. The data collected were analyzed for omissions or inaccuracies, then organized into tables, graphs and flow charts to provide a concise body of technical and cost data suitable for the engineering analyses required in Phase II of this contract. Maps illustrating estimated grade and thickness of the oil shale were prepared, some of which are included as exhibits to this report. A preliminary mine layout was performed to test the completeness of the collected data.

Jan 1, 1975

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By J. E. Hipp

Three electrostatic field sensing proximity warning devices were tested using full-scale cranes and power line systems, a scaled model facility, environmental testing facilities, and theoretical/numerical analysis. The design objective of each device is to assist in safe crane operation near overhead power lines. Several design deficiencies (varying from device to device) were observed, including inadequate overlap in sensitivity ranges, utilization of vacuum tubes and electro-mechanical parts, temperature sensitivity and inaudible alarms. In addition, the testing showed major device limitations including sensitivity to boom orientations and length, polarization dependent responses, and unreliable operation in the presence of multiple power line circuits. The multiple power line circuit problem is intrinsic to electrostatic sensing devices. The remaining deficiencies and limitations are correctable within a state-of-the-art design. This investigation is not intended to evaluate the safety aspects or policy of utilizing proximity warning devices. Rather, the purpose is to determine the performance characteristics of such devices in relation to the criteria specified in proposed MSHA regulation 77.805-4 (i. e., the devices must alarm at a distance of 10 feet from the power line).

Jan 1, 1980

By Rudolf E. Greuer

Two computer programs for the real-time calculation of concentration distributions in the ventilation system of underground mines were designed. They allow one to simulate the movement of fumes or other contaminants with the ventilating air, the calculation of concentrations at any given point and time, and the determination of the total contaminant exposure at different places in the mine. Multiple and time variable contaminant sources can be handled and recirculation is no obstacle. The, first program is based on an airflow distribution which has, in the input data, to be stated. The second program has been linked to in existing program for the calculation of airflow distributions. Two versions of this second program are provided to accommodate the two existing programs. Several executed examples demonstrate the program performance.

Jan 1, 1981

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By J. L. Kohler

This final report on Bureau of Mines Contract J0348005 presents the results of an investigation into the development of a Management Information System (MIS) for underground coal mines. The motivation for the research is the unrealized potential for increasing safety and productivity of the well developed mine monitoring system technology. The intent of this project was to examine the information issues, various design aspects of an integrated monitoring/MIS, and associated application concerns, such as the impact of this technology on safety. The work performed on this contract used mine ventilation as a prototypical example. The report is presented in five chapters and six appendices. In addition to the introduction and conclusions chapters, one chapter deals with ventilation MIS system requirements; another with the formulation of a knowledge-based expert system (KBES) structure to implement the integrated ventilation monitoring/MIS system, and one on the health and safety implications of the system. The appendices present details of the KBES system application with an example using a mine ventilation simulator (PSU/MVS). An important conclusion is that a KBES formulation of an integrated monitoring/ MIS for coal mine management is feasible and desirable.

Jan 1, 1986