Search Documents

By J. C. Franklin

The Bureau of Mines substantially reduced shale degradation in a coal mine by two spray coat applications of a water-base epoxy sealant. More than 12,700 square feet of passageways were treated, and in 18 months only one failure occurred. This failure was due to improper spray application, Material costs averaged 13 cents per square foot, and labor costs were 7 cents per square foot. Labor included moving all materials into the mine, the setup time for each of the areas coated, and application of coatings.

Jan 1, 1977

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

Provide a portable crushing capability to keep conveyor haulage close to the working face and permit more efficient and safer ore handling in low headroom, hardrock mines. Approach A readily portable jaw crusher is used which meets machine size, feed rock size, product size, and throughput requirements for low headroom, hardrock mines. How It Works The crusher is mounted on wheels to expedite frequent moves and to allow crushing of mined rock or ore near the working face. The crushed product is then placed on conveyor belts that are ex-tended as the crusher is moved. Keeping crushing and conveyor haulage near the face minimizes the haulage distances for trucks and loaders. Loading and haulage of run-of-mine ore is frequently the highest operational cost in underground mines. These costs can be significantly reduced by use of a belt conveyor, which is a common practice in coal and other soft mineral mines. The new low-profile hard rock crusher gives the same advantage of extensive belt haulage capabilities to low headroom, hardrock mines. The low-profile crusher will accept feed up to 30 inches when operating under 11 feet of headroom. The headroom required for crusher operation was reduced by tilting the jaws, feeding the crusher horizontally, and placing the eccentric shaft at the back or in a horizontal plane with the jaws. Material is fed by an

Jan 1, 1981

Allow miners to communicate via the pagerphone system when they are not near one of the phones. Approach A small lightweight pagerphone, having crocodile clips which pierce the phone line insulation, was developed. How It Works The Portable Telephone/Intercom is temporarily clipped onto an existing pagerphone line at any location, and operated like an intercom. It is riot necessary to strip the insulation from the pagerphone line to make the connection. In addition to the clips for connecting to pagerphone line, the Portable Telephone/Intercom consists of a small belt-carried control box, an ear-phone, and a bone-conduction microphone which is attached to the webbing in a miner's helmet. All together, these components weigh only 20 ounces including the batteries

Jan 1, 1977

By Martin Harper

This paper concludes a five year program on research into the use of a portable X ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively coupled plasma optical emission spectroscopy (ICP OES). The filter samples were collected using different filter holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.

Jan 1, 2007

By R. G. Gürtunca

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2009

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By George S. Rice

Potash is riot only an important ingredient in the manufacture of many products of modern industry, such as chemicals, explosives, medicines, paints, soap, matches, glass, paper, aniline dyes, bleaching agents, and a host of others, but is indispensable in agriculture. Justus von Liebig is credited with being the first to discover, about 1858, that potash salts in the soil constitute an essential plant food which is not replaced by nature when exhausted through continued cultivation, that this exhaustion results in a decreasing yield of crops, and that the virgin productivity of the soil may be restored, and indeed even increased, by the addition of suitable potash fertilizers. The fact is now well established that wherever intensive cultivation is employed, whether for the raising of cereals, cotton, tobacco, fruit, or garden truck, the replenishment of the potash content of the soil is essential to the maintenance of production. Hence potash is of primary importance in modern life, not only for the economic welfare of industry but for the production of valuable raw materials and the very food supply of the nation itself. SOURCES OF POTASH The main sources of commercial potash are: (1) The solid deposits of soluble potash minerals, such as carnallite, sylvinite, and kainite; (2) sea water, brines, and salt-lake deposits containing appreciable amounts of potash salts associated with sodium salts; (3) vegetable substances, such as wood ashes, bee sugar residues, seaweed, and sunflower stalks; (4) animal material, such as wool washings; (5) products resulting from the decay of organic nitrogenous matter, such as Indian niter; (6) dust in flue gases from cement kilns or in the top gases of iron blast furnaces; and (7) insoluble potash minerals, including alunite, feldspar, leucite, muscovite, and glauconite, all of which contain a considerable quantity of potash.1

Jan 1, 1927

By John E. Conley

Of the three chemical elements most vitally essential for plant growth the United States, before World War I, had developed ample domestic supplies of but one-phosphorus. During and shortly after the war period, the fixation of nitrogen was greatly expanded in this country, as in many others, insuring a supply adequate for agriculture as well as for munitions. However, in spite of a search for sources of the third element, potassium, which began years before the war, attained almost frantic intensity between 1914 and 1919, and continued for 10 years thereafter, it was not until 1921 that the American Trona Corporation put its Searles Lake operations into continuous production. This company in 1926 became The American Potash & Chemical Co. but has never supplied much more than 15 percent of the potash consumed in the American market. Likewise, though discovered in 1921 in drill cuttings from oil wells, it was not until 1926 that domestic deposits of potassium salts adequate to render the United States independent of foreign sources of supply were proved to occur in the Permian Basin of Texas and New Mexico.

Jan 1, 1944

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By David Hill

The Australian underground coal mining industry has made extensive use of the Coal Mine Roof Rating (CMRR) classification system for a diverse range of purposes in recent years. These include mining method selection, and coal pillar and roof support design. This paper outlines a series of case histories, from large-scale feasibility studies to local support design investigations, that collectively illustrate the broad applicability, advantages, and usefulness of the methodology, as well as some of the current limitations. The key role of the CMRR in an overall hazard definition methodology is demonstrated for a major Australian project, and some ideas with regard to the future application of the CMRR, in the context of geotechnical risk management within a progressive, highly productive extractive industry, are put forward.

Jan 5, 2007

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By G. B. Shea

Among the many engineering problems directly related to conservation in the petroleum industry, that of crude-oil emulsions continues to be important. Emulsions of water and oil always have constituted one of the most serious forms of waste in the oil fields, and the necessity of dehydrating emulsified crude petroleum to obtain marketable or pipe-line oil confronts operators in many fields with a major operating problem. In 1926 the Bureau of Mines published a comprehensive treatise s on oil-field emulsions dealing with field conditions, practical methods of dehydration, and physicochemical characteristics of the formation and resolution of emulsions. Although this bulletin is still available and may be obtained from the Superintendent of Documents, Washington, D. C., and although its contents are a valuable reference on the subject of emulsions, knowledge regarding the physical properties of emulsions and the phenomena of dehydration has increased greatly within the last decade. With the information gained through continued scientific research, substantial improvements have been made in the art of resolving petroleum emulsions. Moreover, in recent years there has been a growing realization of the importance of emulsion-preventive measures that has led to more critical examination of the causes of emulsions and methods of eliminating or at least reducing the degree of emulsification. Conditions causing agitation and commingling of oil and water and the formation of "cut oil" often are within the control of the producer, thereby making it possible to utilize preventive or remedial measures by which emulsification may be minimized or avoided. In fact, many companies have materially reduced their treating costs as a result of careful studies in emulsion prevention and proper handling of "wet" production. Of course, in many instances preventive measures or the correction of conditions causing emulsification cannot be achieved practically or economically, and the emulsions that form must be treated regardless of the care exercised or the money spent in attempting to prevent their formation.

Jan 1, 1939