Search Documents

By Frank J. Cservenyak

Curtailment of bauxite importation by enemy activities during World War II focused attention on the necessity of developing domestic deposits of aluminous materials. Large quantities of aluminum ores such as kaolin, siliceous bauxites, high-iron bauxites, anorthosite, and diaspore clays are available but not readily amenable to Bayer processing because of excessive impurities. The Bayer process, which is the only commercial method in use in the United States for producing metallurgical-grade alumina, requires a high Al2O3 bauxite relatively low in SiO2 and Fe2O3. The Bureau of Mines was charged by Congress to investigate processes for the production of alumina from these low-grade ores. One part of the program was an investigation, in the laboratory and pilot plant, of the recovery of alumina by the lime-soda sinter process. Ores comprising kaolin, diasporic clays, anorthosite, and siliceous bauxites have been investigated and studied in the laboratory and pilot plant, and a series 'of reports covering these investigations has been prepared.

Jan 1, 1948

By M. B. Royer

Sulfur is present in many ores and other raw materials that are used in the production of metals and alloys of industrial importance. Its presence, especially in ferrous-metal products, generally is undesirable because of its detrimental effect during processing and upon various physical properties of the finished metal. Therefore, various methods are resorted to for elimination of the element to some specified maximum final content. Such removal or elimination of sulfur is designated as desulfurization.

Jan 1, 1948

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By J. V. Batty

Various ores from deposits in the Boulder Dam Recreational Area, Clark County, Nev., were submitted for ore-dressing tests as part of the Bureau of Mines studies of western manganese ores. The Virgin River manganese deposit is situated on the Virgin River arm of Lake Mead, 5 miles from Bonelli's Point, which was formerly the junction of the Virgin and Colorado Rivers. It is 20 miles from Overton, Nev., and 26 miles from Boulder City, Nev. The ore body, composed of wadlike manganese in a tuffaceous gangue, is a flat-lying bed overlain with beds of gypsum and basalt. Two ore samples were submitted by engineers of the Bureau for ore-dressing investigation. Low-grade sample 1 was a composite of channel samples cut from outcrops of the ore body; sample 2, of intermediate manganese grade, was taken from the dump-at the exploratory shaft sunk by the Bureau. The Boulder City manganese deposit is situated in the Boulder Dam Recreational Area -3 miles southwest of Boulder City. The ore body is a manganiferous gypsum bed 32 feet thick, slightly inclined from the horizontal. The ore sample submitted-by engineers of the Bureau for-testing was taken from channel cuts in the walls of the shaft, which cuts through the bed vertically.

Jan 1, 1948

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By H. M. Cooper

The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment and details of the procedure are given in A.S.T.M. Designation: D271-44.:2. According to the specifications, the following features should be incorporated in the equipment used: 1. Oven must have uniform temperature in all parts. 2. Oven must be constructed with minimum of air space. 3. Oven must have means of changing the air two to four times per minute. 4. Air must be dried over sulfuric acid (sp. f-7. 1.84). The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general arid of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.

Jan 1, 1948

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By Edward P. Barrett

This investigation was a part of the Bureau of Mines program for the production of critical and essential materials needed for the war. The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from the low-grade iron ores of Minnesota. This investigation was conducted by the Bureau of Mines to determine the workability of the proposed shaft-furnace process and its possible use in connection with an experimental plant for the gasification of lignite operated by the Coal Division of the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1948

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By Owen W. Terry

During the summer of 1943 the Bureau of Mines conducted an investigation and program of churn drilling on the McIlhon and adjoining Pearson land in the Mineral Point district of Iowa County, Wis. Sixteen holes, aggregating 1,570 feet .of bore, were completed. The work was undertaken as part of a general investigation of the zinc-and lead-producing area of southwestern Wisconsin at a time when great effort was being made to increase the production of Metals important to the war program. The Bureau's drilling program supplemented a previous drilling pro-gram conducted by the Vinegar Hill Zinc Co., and demonstrated the presence of a strongly mineralized zone at relatively shallow depths.

Jan 1, 1948

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By T. J. Ballard

The Track Rock corundum mine was among the numerous corundum deposits investigated during the war by the Bureau of Mines in an effort to develop domestic reserves of that critical mineral. In the investigation of this property 562 feet of trenches were excavated and a l25-foot adit was reopened for the purpose of locating veins to of corundum which had been previously reported to occur in that locality. Only very minor amounts of corundum were disclosed in both the surface workings and the adit. The project was begun in May 1943 and completed in November 1943.

Jan 1, 1948

By T. J. Ballard

The Rickard mine in York County, S. C., named for the original owner, Alexander Rickard, was operated about 50 years as. No records are available of the quantity of corundum shipped. Pratt states, "Many tons were picked up from the surface and shipped." The mine was visited on August 6, 1943, by the author, accompanied by Gilbert W. Withers of Atlanta, Ga. Investigation of the property was begun by the Bureau of Mines after some initial work by the Mi-Cor Corp., a company organized by Gilbert P. Withers of Atlanta to explore the property. In conducting the Bureau program, 754 linear feet of trenches were dug, 110 feet of old drifts cleaned out and examined, and 38 feet of shaft retimbered.

Jan 1, 1948

By T. J. Ballard

Chromite deposits in the vicinity of Louise, Troup County, Ga., were studied y the Bureau of Mines from September 1, 1942, to March, 15, 1943. They are about three-fourths of a mile southeast of Louise and 8 miles northeast of La Grange, Troup County, Ga. The existence of chromite deposits in that area has been known for more than 75 years, but no active prospecting was done until World War I. Prospecting continued intermittently' until 1928. The Bureau became interested in the deposits in connection with its strategic minerals investigations during World War II. The chromite in these deposits occurs as grains ranging from "pin-head" size to 3/8-inch and occasionally 1 inch. Some of the material is magnetic, indicating the presence of magnetite. Of the 300 samples taken during the course of the project, 266 were analyzed. Tables showing the analyses accompany this report.

Jan 1, 1948

By W. H. Kerns

The Simon & Coles manganese deposit in Sherman Valley, Bedford County, Pa., was investigated by the Bureau of Mines during the fall of 1942. Two churn-drill holes; 65 and 75 feet deep were bored, and 8 channel samples were taken. Manganese occurs at this property in the form of psilomelane and manganiferous iron as replacement of the red sandy shale of the Much Chunk-formation. Two cars of manganese ore had been shipped by the owners in 1940, of which one averaged 10.9 percent manganese and the other 21.3 percent manganese. One car of hand-sorted manganese ore that averaged-45 percent manganese was shipped in 1942.

Jan 1, 1948

By Homer J. Ballinger

The Mary Arnold Mining Co. in 194.3 owned 292 acre s of mineral land in Christian County, Mo., and was one of two companies with milling facilities in southern-central Missouri. Production from this property between 19.37 and 1941 amounted to 1,718 tons of zinc in the form of zinc concentrate. Because of the urgent war requirements for additional zinc and the existing facilities for treatment of zinc-lead ores at these mines, in the winter of 1943-44, the Bureau of Mines investigated the deposits by churn drilling in an endeavor to outline enough ore to maintain production of zinc from this district. Five holes aggregating 1,043 feet were bored.

Jan 1, 1948

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By Arthur S. Swanson

The DuBois fluorite property in the southwestern part of Hardin County, Ill., has been active intermittently since 1904 and has produced an estimated total of 1,000 to 2,000 tons. The persistence of the vein and the stratigraphy suggested extensions of the ore body formerly mined. The Bureau of Mines investigated the property by core drilling early in 1944. Four holes were bored which totaled 1,106 feet and extended along a strike length of 1,150 feet. The data obtained in the course of the investigation are presented in this report.

Jan 1, 1948

By T. J. Ballard

The Tallapoosa Copper mine in Haralson County, Ga., has been operated, or under development at various times since before the Civil War. The geology of the deposit is similar to that of many of the pyrite deposits occurring in the belt of ancient crystalline and metamorphic rocks that extends diagonally northeast-southwest across the State. The Bureau of Mines, in its program of investigation of, strategic mineral deposits, diamond-drilled four holes totaling 1,570.3 feet at the deposit during the period June to September 1947 to verify the old drill records and the continuation of the deposit at depth.

Jan 1, 1948

By M. Howard Berliner

During the spring of 1944, the Bureau of Mines investigated the Crescent mine area near the village of Rewey, Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation's war program. The Bureau of Mines completed 24 churn-drill holes in an area immediately to the west of a mineralized section which had been mined through shallow workings for lead and zinc more than 40 years earlier.

Jan 1, 1948