Search Documents

By M. R. Geer

Full-seam mining with continuous mining machines in dirty coal beds may increase loss of coal in the washery refuse. At one mine mentioned in this report the loss of salable coal was increased sixfold. Cleaning trials were made on three samples of jig refuse in a dense-medium pilot plant to demonstrate the application of this process to the recovery of coal from waste. These tests demonstrated that coal could be separated from impurity with the same degree of sharpness obtained in treating raw coal by dense medium. However, the recovery efficiency achieved in treating refuse averaged distinctly lower than that possible with raw coal because of the greater proportion of intermediate-density material in the feed and the lower yield of clean coal.

Jan 1, 1955

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By Louis A. Panek

The practice of roof bolting, now recognized as an effective method of support, is based largely on rule of thumb. Among the various applications of bolting, the support of stratified mine roof is by far the most common. The general principles relating to this type of reinforcement are presented in two companion reports; the first describes the function of the bolts, the bolting pattern, and the behavior of bolted roof (1), 2/ and the second describes the design of the models and the theory of the experimental method (2). This report presents a rational method for designing systems of vertical bolts to reinforce horizontally bedded mine roof, developed from model tests. The structure treated herein may be described as follows: The immediate roof, consisting of beds of like material and equal thickness with no bond between them, is reinforced by vertical bolts installed in straight lines across the opening; the case of suspension is excluded because the bolts are assumed not to extend above the immediate roof. The assumption is made that the behavior of the lowest bed approximates that of a rectangular plate clamped along two opposite sides (the ribs). These specifications represent approximately the roof conditions encountered in mining bedded deposits of all kinds - coal, potash, iron ore, etc. Thus, for the design of a roof-bolting system a quantitative solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, how does the support depend upon the length, spacing, and tightness of the bolts?

Jan 1, 1956

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

By C. C. Popoff

The growth of the aluminum-smelting industry in the Pacific Northwest, resulting from national defense requirements, emphasized a need for local sources of alumina to supplement the alumina production shipped from the East. Because supplies of foreign bauxite were being interrupted and our domestic bauxite reserves were inadequate, it was necessary to expedite the investigation of other possible sources of alumina during World War II. A program of investigation of high-alumina clay deposits in the Northwest was carried out jointly by the Federal Geological Survey and the Federal Bureau of Mines. As part of this program the Cowlitz clay deposits near Castle Rock, Wash., were explored by the Bureau of Mines in 1942-43. These deposits are near railroads, tide-water, and Bonneville Power Administration lines and within 22 to 100 miles of 4 aluminum-reduction plants.

Jan 1, 1955

By H. R. Shell

The work on synthetic mica and related subjects is being reported in a series of technical articles (see Supplementary Bibliography), each of which describes some special aspect of the subject. This is the final report on chemical analysis of the fluoride-containing silicates. A condensation of this report has been published (26).3/ Chemical analysis affords one of the best means of ascertaining the final com-position of either a heterogeneous mass or a single pure crystal, particularly where some constituents may be volatile. The analysis of fluoride-containing silicates was not so well known or understood that highly accurate results were commonplace. For example, on synthetic mica a university laboratory reported 11.6 and 9.2 percent fluoride when at least 13.3 and 11.3 percent were present, respectively; a commercial testing laboratory reported 9.14 percent as compared to 12.6 percent; and a glass company reported 7.0 percent as compared to 9.0 percent present. No intimation is made that these analysts could not have done better, but the point to be stressed is that the methods in use were long, tedious, and generally required a certain familiarity for best results.

Jan 1, 1956

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By Lloyd Williams

1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sewanee, has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although same coal has been produced from them. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By M. J. Spendlove

A progress report is presented on a research program in which an attempt was made to develop a practical sulfide-volatilization process for recovering tin from low-grade Bolivian ores. Shaft-furnace designs and operating techniques were studied in a series of experiments in which the objective was to sulfidize cassiterite to stannous sulfide, remove the stannous sulfide by volatilization, reconvert the stannous sulfide to stannous oxide, and collect the resulting fume. A shaft furnace was developed and operated in a final test in which many of the previous difficulties were surmounted. Since the supporting funds were exhausted at this point, the project was discontinued; recommendations for further improvements in furnace design and operation were made on the basis of interpretation of experimental results obtained in shaft-furnace experiments and other related studies.

Jan 1, 1955

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of nine manganese-ore samples in 1953-1954. Three samples were from Nevada and the other six from California. These samples represent marginal or low-grade ores from deposits that have been mined selectively in the past. The present interest lies chiefly in the possibilities of concentration of the remaining low-grade ores for economical exploitation. The treatment methods included gravity concentration and flotation in most cases. Results were sometimes unsatisfactory, particularly when the ore was too fine grained for liberation of the minerals within economical grinding range. The contaminating gangue minerals, such as quartz and iron oxides, were locked with the manganese to an extent that prevented separation of high-grade concentrates with satisfactory recovery. In cases where fairly good concentrates were made, it was at the expense of recovery, a condition typical of low-grade ores.

Jan 1, 1955

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By R. C. Buehl

An experimental iron blast furnace of 3-foot-diameter hearth, producing about 12 tons of metal per day, was operated for 2 weeks with various proportions of anthracite replacing a corresponding amount of coke. The furnace operated well with anthracite in amounts up to 40 percent of the total fuel and produced metal of uniformly low sulfur and normal silicon contents. An increase to 50 percent anthracite during two attempts resulted in poor operation and the charge hung in the s haft of the furnace. INTRODUCTION Anthracite production in Pennsylvania decreased from 84,400,000 net tons in 1926 to 40,600,000 net tons in 1952, and there was a further decline in 1953 to 30,900,000 net tons. Employment in the anthracite industry dropped from 165,000 men working an average of 244 days per year in 1926 to 57,900 working an average of 163 days per year in 1953,3/ which has naturally resulted in considerable unemployment in the region. The industry is actively engaged in promoting new uses for anthracite to increase the demand and thus improve economic conditions in the region. One possibility is the use of anthracite to replace part of the coke for smelting iron ore in blast furnaces. The tests in this report were made to determine whether this use of anthracite would be feasible.

Jan 1, 1955

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By R. C. Ellman

This report presents results of a series of tests on grindability of lignites and factors that influence grindability determination. All grindability tests in this investigation were made in the standard Hardgrove test apparatus. In addition to tests on standard samples of equilibrium moisture content, grindability determinations were made on air-and oven-dried samples of lignite representing the complete range of moisture content from normal bed moisture to nearly moisture-free conditions. Grindability index for all tests was calculated both by standard method and by an alternate or "corrected" method of calculation based on directly measured weight of fine-particle material produced in the grindability test. The second method of calculation allows more satisfactorily for loss of moisture during testing of high-moisture samples.

Jan 1, 1955

By P. R. Perry

This publication is a compilation of tested methods for the analyses of titanium tetrachloride, titanium sponge, and various intermediate materials and products. They are presented in concise form without the detail usually found in publication of new methods because many of them are modifications of well known procedures. The Electrometallurgical Experiment Station, Boulder City, Nev., has been developing titanium production methods since 1945. Most of this development was on a modified Kroll Process but also included work on sodium reduction and electrolytic methods. During these years a large variety of samples were analyzed. Most of the analytical problems were solved using published methods or modifications of the same. At the start, there were no published procedures for analyzing titanium sponge using spectrochemical methods. A great deal of study was given to testing several of the well known techniques, and some of them, such as direct sparking of the metal, proved to be completely unsatisfactory. Solution-spark techniques were finally tried, and satisfactory procedures were developed for some of the more common impurities. These spectrochemical methods were then put into routine use for several months before their publication.2/ Some new modifications have been made, and techniques have been developed to determine other impurities found in titanium sponge and tetrachloride. All spectrochemical methods used in 1954 are included in this publication.

Jan 1, 1955

By H. P. Holmes

Tonnage quantities of hafnium metal have been prepared in Kroll-process equipment designed for producing zirconium. Some slight process modifications have been necessary, but overall operation is the same as for zirconium. Hafnium oxide is chlorinated in the presence of carbon and the resultant hafnium tetrachloride reduced by magnesium metal. Byproduct magnesium chloride is removed in a high-vacuum distillation step and the hafnium sponge metal crushed for further use. Arc-melted metal can be forged and rolled to sheet, but the best material produced to date would not be considered cold ductile. INTRODUCTION This investigation is part of the program for the production of pure metals from domestic and foreign ores that has been underway at the Bureau of Mines for several years. It was done in cooperation with the Atomic Energy Commission and the Bureau of Ships.

Jan 1, 1955

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955